AXIS D2110-VE Security Radar User Manual
AXIS D2110-VE Security Radar Table of Contents Solution overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Where to install the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting tilt . . . . . . . . . . . . . .
AXIS D2110-VE Security Radar Solution overview Solution overview 1 2 3 4 5 AXIS D2110-VE Fixed dome camera PTZ camera and illuminator Door controller Surveillance center 3
AXIS D2110-VE Security Radar Product overview Product overview 1 2 3 4 5 6 7 8 9 10 11 12 13 Control button Network LED Status LED Power LED PoE out LED microSD card slot DC power connector I/O connector Relay connector Grounding screw Network connector (PoE in) Network connector (PoE out) Intrusion alarm sensor Where to install the product Note Do not repaint the detector. The paint may seriously impact the detector’s performance. The detector is intended for monitoring open areas.
AXIS D2110-VE Security Radar Product overview Avoid aiming the radar towards another radar. If more than two radar detectors of are mounted close together they may interfere with each other. To avoid interference, see Install multiple radars on page 8 . Mounting height For optimal performance, install the detector 3.5 m (11 ft) above ground. Note If you install the detector at a different height, enter the actual mounting height in the product’s web pages before calibrating the radar.
AXIS D2110-VE Security Radar Find the device on the network Find the device on the network To find Axis devices on the network and assign them IP addresses in Windows®, use AXIS IP Utility or AXIS Device Manager. Both applications are free and can be downloaded from axis.com/support. For more information about how to find and assign IP addresses, see the document How to assign an IP address and access your device on the device page at axis.com. Access the device 1.
AXIS D2110-VE Security Radar Additional settings Additional settings Need more help? You can access the built-in help from the device’s webpage. The help provides more detailed information on the device’s features and their settings. Configure the detector The detector is ready to use as soon as it is installed. The default live view will show the radar coverage and any detected movement, and you can add detection zones and rules right away.
AXIS D2110-VE Security Radar Additional settings Image requirements: • Supported file formats are jpeg and png. • Use an image with the same proportions (16:9) or resolution (1920x1080) as the live view. If the image is smaller it will be scaled to fit the window. If the proportions are wrong, the image will not fill the entire video stream. • Crop the image to fit the coverage of the radar as closely as possible before uploading it.
AXIS D2110-VE Security Radar Additional settings 1. Go to Settings > Radar > General and select Coexistence. Set up rules and alerts How to record video from a camera when motion is detected This example explains how to set up the detector and a camera so that the camera starts recording to the SD card five seconds before the detector detects motion and to stop one minute after. Connect the devices: 1. Connect a cable from an I/O output on the detector to an I/O input on the camera.
AXIS D2110-VE Security Radar Additional settings 1. Go to Settings > System > Events and add a rule. 2. Type a name for the rule. 3. From the list of conditions, select an include zone under Radar motion. To set up an include zone, see Add an include zone on page 11 . 4. From the list of actions, select Record video. 5. Set the prebuffer to 5 seconds. 6. Set the postbuffer to 60 seconds. 7. Select SD card from the list of storage options. 8. Click Save.
AXIS D2110-VE Security Radar Additional settings About detection zones To determine where to detect motion, you can add multiple zones. Different zones can be used to trigger different actions. There are two types of zones: • An include zone is an area in which moving objects will trigger rules. The default include zone matches the entire area covered by the detector. • An exclude zone is an area in which moving objects will be ignored.
AXIS D2110-VE Security Radar Additional settings Enable Short-lived object and set a delay time from when the radar starts tracking an object until it can trigger and alarm. The timer starts when the radar first detects the object, not when the object enters the include zone. • Filter on object type: The detector will classify objects depending on the radar echo that they produce. If it can’t determine the object type, the object will be classified as Unidentified.
AXIS D2110-VE Security Radar Troubleshooting Troubleshooting If you can’t find what you’re looking for here, try the troubleshooting section at axis.com/support. Reset to factory default settings Important Reset to factory default should be used with caution. A reset to factory default resets all settings, including the IP address, to the factory default values. To reset the product to the factory default settings: It is also possible to reset parameters to factory default through the web interface.
AXIS D2110-VE Security Radar Troubleshooting Problems setting the IP address The device is located on a different subnet If the IP address intended for the device and the IP address of the computer used to access the device are located on different subnets, you cannot set the IP address. Contact your network administrator to obtain an IP address. The IP address is being used by another device Disconnect the Axis device from the network.
AXIS D2110-VE Security Radar Specifications Specifications To find the latest version of the product’s datasheet, go to the product page at axis.com and locate Support & Documentation. LED Indicators Status LED Indication Green Steady green for normal operation. Network LED Indication Green Steady for connection to a 100 Mbit/s network. Flashes for network activity. Amber Steady for connection to a 10 Mbit/s network. Flashes for network activity. Unlit No network connection.
AXIS D2110-VE Security Radar Specifications Network connector (PoE out) Use this connector to supply power to a camera. Power over Ethernet IEEE802.3at Type 2, max 30W I/O connector Use the I/O connector with external devices in combination with, for example, motion detection, event triggering, and alarm notifications.
AXIS D2110-VE Security Radar Specifications Power connector 2-pin terminal block for DC power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A. Relay connector CAUTION Use single core wires for the relay connector. Function Specifications Type Normally open Rating 30 V DC/5 A 125 V AC/10 A 250 V AC/5 A Isolation from other circuitry 2.
User Manual AXIS D2110-VE Security Radar © Axis Communications AB, 2019 Ver. M1.6 Date: March 2020 Part No.