0
Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
Safety Precautions • Only use the supplied power adaptor, and do not use the power adaptor in o temperatures over 40 C, and only use in a dry location • Only use 9V batteries in the main unit and the motion sensors, as there is a risk of explosion if an incorrect battery type is used • Please dispose of any used 9V batteries at a proper facility • Do not operate the device: o In areas where blasting is in progress o Where explosive atmospheres may be present o Near medical equipment o Near lif
POWERED OFF. The Axesstel router can transmit signals that could interfere with this equipment.
Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Axesstel.
Table of Contents 1 2 3 Introduction ..............................................................................................................10 Product Overview.....................................................................................................10 Using your AX52R ...................................................................................................13 3.1 Package Contents ..........................................................................................
- ................................................................................................................................14 - ................................................................................................................................14 Device is Off .............................................................................................................14 Battery ................................................................................................................
In register status.......................................................................................................14 - ................................................................................................................................14 Not in Setting / Registering Mode ............................................................................14 Arming / ....................................................................................................................14 Disarming ....
Disarmed ..................................................................................................................14 Zone 3 ......................................................................................................................14 Armed.......................................................................................................................14 - ................................................................................................................................
4.5 UIM Card.......................................................................................................... 18 4.6 Changing the Default Password ................................................................... 20 4.7 Adding / Removing Motion Sensors ............................................................ 21 4.8 Adding / Removing SMS Numbers ............................................................... 22 4.9 Adding / Removing Call Numbers ................................................
1 Introduction This user manual will help you place, configure and use your AX52R Alert System. 2 Product Overview The AX52R is an easy to install, use and maintain alert system, which can provide peace of mind and security without the need for an expensive security contract. Some features described in this manual may not be supported by your service provider or may not be available with your network account. For details of the services and accounts available, contact your service provider.
SMS / Call Alerts if the Motion Sensor is Triggered Notify up to 8 friends and neighbors via call or SMS when motion is detected to increase chances of a close-by responder. You can program up to 3 SMS numbers and 5 call numbers. Emergency Backup Battery An AC adaptor with a 9V backup battery provides continued functionality in the event of a power outage.
Easy to use Main Unit 9 LED indicators represent the product status. The unit is also very easy to program and to modify the list of SMS / Call contacts.
3 Using your AX52R 3.1 Package Contents • • • 1x Main Unit 2x Motion Sensors with brackets 1x Power Adaptor 3.2 Knowing your Main Unit Your AX52R is designed to be wall mounted, or it can simply be placed on a shelf. All the LEDs are easily visible while the power cord will connect at the back. 3.3 LEDs The AX52R has 9 LEDs to determine status of the device. The functionality of the LEDs can be found in the table below.
LED Power Battery Signal Setting / Register Arming / Disarming Zone 1 Green Device is Turned On Battery power is Full / Medium Registered to the network and signal level is good In process of setting Alarm Flashing Green - Red Off - Battery Power is Low Signal is poor - In register status - Device is Off No Battery is installed No network signal - Alarm is Armed Armed - Alarm Detected Not in Setting / Registering Mode Alarm is Disarmed Disarmed Zone 2 Armed - Alarm Detected Disarmed Zo
4 Using your AX52R 4.1 Battery Installation / UIM Card Installation into Main Unit Your AX52R main unit may need a UIM Card so that it can communicate with the wireless network. It also supports battery backup. Please follow the instructions below to install the UIM Card and the 9V battery. Note: It is advisable to install your UIM Card before you install the 9v battery.
4.2 Battery Installation into Motion Sensor To install the battery into the Motion Sensor please follow the instructions below.
4.3 Connecting the Power Adaptor To connect the power adaptor, please follow the instructions below.
4.4 Placement of Main Unit / Motion Sensor 4.4.1 Main Unit The keypad should be placed near the entry / exit point of the house. 4.4.2 Motion Sensor Place on shelves or walls to detect motion within 50 meters, great for rooms with lots of windows. 4.5 UIM Card PLEASE NOTE: THIS SECTION ONLY APPLIES TO DEVICES REQUIRING UIM CardS FOR OPERATION Unlocking your UIM Card The UIM Card for your device may have a PIN code enabled as default.
Activate/ Deactivate the PIN Code To toggle between activating and deactivating the PIN Code, please enter the following on your keypad *#→password→07->PIN Code→Func Key Changing your PIN Code You may want to change your UIM Card PIN code to something more memorable to do this you can enter the command below *#→password→08->Existing PIN Code*→New PIN Code→ Func Key PUK Code If you enter an incorrect PIN code 3 times, then you will need to enter your PUK code in order to unlock your device.
4.6 Changing the Default Password Now that the battery is installed and the power adaptor connected you are ready to use some of the more advanced features of the AX52R. To change the default password please follow the instructions below. Using your keypad please enter the following *#→password→00->new password*→new password→Func Key NOTE: IT IS ADVISABLE TO CHANGE YOUR PASSWORD AS SOON AS YOU CONNECT THE UNIT *Default password is 1234.
4.7 Adding / Removing Motion Sensors To add motion sensors to the AX52R please follow the instructions below. Up to 64 Motion sensors can be added across 4 zones.
*#→password→82→Func Key *#→password→83→Func Key *#→password→84→Func Key zone2 zone3 zone4 Please note that removing sensors will remove all the sensors in the specific zone. 4.8 Adding / Removing SMS Numbers When your alarm is triggered in any zone, you can choose to send an SMS to up to 3 numbers. To add the SMS numbers into your AX52R please follow the instructions below. *#→password→11→SMS Num.1*→SMS Num.1→Func Key *#→password→12→SMS Num.2*→SMS Num.2→Func Key *#→password→13→SMS Num.3*→SMS Num.
Please note that you have to enter the desired number twice. The number that you entered will need to match. If the numbers do not match then the unit will beep 3 times. If the numbers match then you will hear 2 beeps. To remove the SMS numbers please enter the details below.
4.9 Adding / Removing Call Numbers When your alarm is triggered as well as sending SMS, the AX52R will also dial 5 numbers of your choice. It is important to note that as the AX52R has no microphone or speaker no conversation will be permissible. To add numbers please follow the instructions below. *#→password→31→Tel Num.1*→Tel Num.1→Func Key *#→password→32→Tel Num.2*→Tel Num.2→Func Key *#→password→33→Tel Num.3*→Tel Num.3→Func Key *#→password→34→Tel Num.4*→Tel Num.4→Func Key *#→password→35→Tel Num.
Please note that you have to enter the desired number twice. The number that you entered will need to match. If the numbers do not match then the unit will beep 3 times. If the numbers match then you will hear 2 beeps. To remove the phone numbers please follow the instructions below.
4.10.1 Arming the AX52R Siren Mode In Siren mode, when the motion sensors are triggered, it will emit a high pitched continuous beep, until the unit is disarmed. To activate Siren mode enter the following: *#→password→01->Arming Key Silent Mode In Silent mode, when the alarm is triggered the high pitched continuous beep will not sound making the intruder unaware that the alarm has been triggered, although SMS / Calls will be sent.
Stay Mode Occasionally you may want to alarm only a certain part of your house, and this can be achieved by using Stay mode. Please note that Zone 4 will only be triggered when using stay mode. In Stay mode, you can activate your alarm so that any motion in zones one, two or three will not trigger the alarm, but if there is any movement in zone four then the alarm will be triggered. In Stay mode you can choose whether the device emits a beep or stays silent when the alarm is triggered.
4.10.2 Disarming the AX52R When disarming the AX52R, you can disarm in multiple ways, and these are described below. Normal Disarming To disarm the AX52R in a normal manner enter the following: *#->password->05->Arming Key Normal disarming Duress Disarming If you are forced to disarm the unit under duress, then SMS / Calls will still be made to the numbers that are stored in your device.
Remote Disarming You can also disarm the AX52R remotely via SMS. To do this the mobile number that you use to disarm the AX52R will need to be programmed as one of the three SMS numbers. To disarm the AX52R by SMS you will simply need to send a text message saying ‘Disarm Alarm’ to the number that corresponds to the SIM that is placed in the AX52R. 4.11 Entry / Exit Delay You can modify the entry / exit delay to suit your needs. 4.11.
4.11.2 Exit Delay No Exit Delay 30 Seconds 60 Seconds 90 Seconds 120 Seconds - *#→password→60→Func Key *#→password→61→Func Key *#→password→62→Func Key *#→password→63→Func Key *#→password→64→Func Key 4.12 Panic Button Your AX52R features a panic button, that when pressed will immediately activate the siren, as well as alerting your friends and neighbors via SMS and Calls. To activate the panic button simply press the ‘PANIC’ button which is located on your main unit.
4.13 Factory Reset If your unit malfunctions or develops any form of software fault then it may be necessary to perform a factory reset.
5 Operating Specifications The Main Unit is only for RX function without TX function, and Motion Sensor (AI100) is only for TX function without RX function 5.
Carrier spacing Maximum output power Channel Spacing 30KHz Channel Band width : 1.23MHz 300mW (24.77dBm) Form Factor Dimension Sensitivity and Dynamic Range : -104dBm ~ -25dBm < FER = 0.5% Molex connector 80PIN 36.2*30*3.
Key SMS number CALL number Zone number Power adapter Battery ASK 433Mhz Band Frequency Carrier spacing RSSI Working Temperature Storage Temperature Humidity 16 3 sets phone number 5 sets phone number 4 zones 5V/2A 9V 433.82Mhz-434.02Mhz 0.
Motion Sensor (AI100) AP Detection mode Key Antenna Detection range LED Key Tamper switch Battery ASK 433Mhz Band Frequency Carrier spacing BS0001 Passive infrared signal Molex connector 80PIN ASK433M Spring antenna 6-8m Red & Green Not support Support 9V 433.82Mhz-434.02Mhz 0.
Maximum output power RSSI Working Temperature Storage Temperature Humidity 4dB < -110dBm -10~+50oC -20~+70oC 5% to 95% 36
AXESSTEL ALERT PRODUCTS CONSUMER WARRANTY AND LIMITATION OF LIABILITY THE AXESSTEL ALERT PRODUCT THAT YOU HAVE PURCHASED, WHEN PROPERLY INSTALLED, CAN BE USED TO DETECT MOTION IN A SPECIFIED AREA AND PROVIDE AN ALERT TO TELEPHONES OR PERSONAL DIGITAL ASSISTANTS THAT YOU SPECIFY. THE PRODUCT IS DESIGNED SOLELY TO PROVIDE AN ALERT. IT DOES NOT PROVIDE SECURITY, OR PREVENT INTRUSION, THEFT OR CRIME. THE PRODUCT IS NOT A SECURITY SERVICE, ALERTS ARE SENT ONLY TO THE DEVICES YOU SPECIFY.
SUCH PRODUCTS, IN ITS DISCRETION, SO THAT ANY DEFECTIVE PRODUCT OR ANY REPLACEMENT PRODUCT SHALL CONFORM TO THE WARRANTY. IF AXESSTEL CANNOT CURE ANY DEFECT ON COMMERCIALLY REASONABLE TERMS, AXESSTEL SHALL REFUND THE VALUE OF THE NON-CONFORMING PRODUCT WITHIN FORTY- FIVE (45) DAYS.
LIMITATION OF LIABILITY. AXESSTEL NOT BE LIABLE TO YOU UNDER ANY CIRCUMSTANCE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, ARISING OUT OF THE USE OR INABILITY TO USE, ANY OF THE ALERT PRODUCTS OR COMPONENTS. AXESSTEL WILL NOT BE RESPONSIBLE FOR ANY LOSS OF PROPERTY, DAMAGE TO PROPERTY, PERSONAL INJURY, DEATH OR OTHER INCIDENTAL DAMAGES, HOWEVER CAUSED, ARISING OUT OF THE USE OR INABILITY TO USE, ANY OF THE ALERT PRODUCTS OR COMPONENTS.
USE AT OWN RISK. YOU ACCEPT THE ENTIRE RISK OF THE USE OF THE PRODUCT. YOU HEREBY AGREE TO RELEASE, DEFEND, INDEMNIFY AND HOLD AXESSTEL HARMLESS FROM AND AGAINST CLAIM OR LIABILITY FOR ANY RISK, LOSS, PROPERTY DAMAGE, PERSONAL INJURY, DEATH AND OTHER EFFECTS MENTIONED ABOVE AT YOUR SOLE COST AND EXPENSE INCLUDING ATTORNEY’S FEES. FCC STATEMENT: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
AND USED IN ACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR INSTALLATION. IF THIS PRODUCT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES: —REORIENT OR RELOCATE THE RECEIVING ANTENNA.
CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. NOTICE: THIS EQUIPMENT SHOULD BE INSTALLED AND OPERATED WITH A MINIMUM DISTANCE 20CM BETWEEN THE RADIATOR AND YOUR BODY.