0
Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
Safety Precautions • Only use the supplied power adaptor, and do not use the power adaptor in o temperatures over 40 C, and only use in a dry location • Only use 9V batteries in the main unit and the motion sensors, as there is a risk of explosion if an incorrect battery type is used • Please dispose of any used 9V batteries at a proper facility • Do not operate the device: o In areas where blasting is in progress o Where explosive atmospheres may be present o Near medical equipment o Near lif
Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Axesstel.
Table of Contents 1 ....Introduction .................................................................................................6 2 ....Product Overview........................................................................................6 3 ....Using your AX54 .........................................................................................9 3.1 Package Contents ................................................................................9 3.2 Knowing your Main Unit .....................
4.8 Adding / Removing SMS Numbers.......................................................18 4.9 Adding / Removing Call Numbers ........................................................20 4.10 Arming / Disarming the AX54 ...............................................................21 4.10.1 Arming the AX54..........................................................................22 4.10.2 Disarming the AX54.....................................................................24 4.11 Entry / Exit Delay ........
1 Introduction This user manual will help you place, configure and use your AX54 Alert System. 2 Product Overview The AX54 is an easy to install, use and maintain alert system, which can provide peace of mind and security without the need for an expensive security contract. Some features described in this manual may not be supported by your service provider or may not be available with your network account. For details of the services and accounts available, contact your service provider.
SMS / Call Alerts if the Motion Sensor is Triggered Notify up to 8 friends and neighbors via call or SMS when motion is detected to increase chances of a close-by responder. You can program up to 3 SMS numbers and 5 call numbers. Emergency Backup Battery An AC adaptor with a 9V backup battery provides continued functionality in the event of a power outage.
Easy to use Main Unit 9 LED indicators represent the product status. The unit is also very easy to program and to modify the list of SMS / Call contacts.
3 3.1 • • • Using your AX54 Package Contents 1x Main Unit 2x Motion Sensors with brackets 1x Power Adaptor 3.2 Knowing your Main Unit Your AX54 is designed to be wall mounted, or it can simply be placed on a shelf. All the LEDs are easily visible while the power cord will connect at the back. 3.3 LEDs The AX54 has 9 LEDs to determine status of the device. The functionality of the LEDs can be found in the table below.
LED Power Battery Signal Setting / Register Arming / Disarming Zone 1 Green Device is Turned On Battery power is Full / Medium Registered to the network and signal level is good In process of setting Alarm Flashing Green - Red Off - Battery Power is Low Signal is poor - In register status - Device is Off No Battery is installed No network signal - Alarm is Armed Armed - Alarm Detected Not in Setting / Registering Mode Alarm is Disarmed Disarmed Zone 2 Armed - Alarm Detected Disarmed Zo
4 4.1 Using your AX54 Battery Installation / UIM Card Installation into Main Unit Your AX54 main unit may need a UIM Card so that it can communicate with the wireless network. It also supports battery backup. Please follow the instructions below to install the UIM Card and the 9V battery. Note: It is advisable to install your UIM Card before you install the 9v battery.
4.2 Battery Installation into Motion Sensor To install the battery into the Motion Sensor please follow the instructions below.
4.3 Connecting the Power Adaptor To connect the power adaptor, please follow the instructions below.
4.4 Placement of Main Unit / Motion Sensor 4.4.1 Main Unit The keypad should be placed near the entry / exit point of the house. 4.4.2 Motion Sensor Place on shelves or walls to detect motion within 50 meters, great for rooms with lots of windows. 4.5 UIM Card PLEASE NOTE: THIS SECTION ONLY APPLIES TO DEVICES REQUIRING UIM CardS FOR OPERATION Unlocking your UIM Card The UIM Card for your device may have a PIN code enabled as default.
Activate/ Deactivate the PIN Code To toggle between activating and deactivating the PIN Code, please enter the following on your keypad *#→password→07->PIN Code→Func Key Changing your PIN Code You may want to change your UIM Card PIN code to something more memorable to do this you can enter the command below *#→password→08->Existing PIN Code*→New PIN Code→ Func Key PUK Code If you enter an incorrect PIN code 3 times, then you will need to enter your PUK code in order to unlock your device.
4.6 Changing the Default Password Now that the battery is installed and the power adaptor connected you are ready to use some of the more advanced features of the AX54. To change the default password please follow the instructions below. Using your keypad please enter the following *#→password→00->new password*→new password→Func Key NOTE: IT IS ADVISABLE TO CHANGE YOUR PASSWORD AS SOON AS YOU CONNECT THE UNIT *Default password is 1234.
4.7 Adding / Removing Motion Sensors To add motion sensors to the AX54 please follow the instructions below. Up to 64 Motion sensors can be added across 4 zones.
*#→password→82→Func Key *#→password→83→Func Key *#→password→84→Func Key zone2 zone3 zone4 Please note that removing sensors will remove all the sensors in the specific zone. 4.8 Adding / Removing SMS Numbers When your alarm is triggered in any zone, you can choose to send an SMS to up to 3 numbers. To add the SMS numbers into your AX54 please follow the instructions below. *#→password→11→SMS Num.1*→SMS Num.1→Func Key *#→password→12→SMS Num.2*→SMS Num.2→Func Key *#→password→13→SMS Num.3*→SMS Num.
Please note that you have to enter the desired number twice. The number that you entered will need to match. If the numbers do not match then the unit will beep 3 times. If the numbers match then you will hear 2 beeps. To remove the SMS numbers please enter the details below.
4.9 Adding / Removing Call Numbers When your alarm is triggered as well as sending SMS, the AX54 will also dial 5 numbers of your choice. It is important to note that as the AX54 has no microphone or speaker no conversation will be permissible. To add numbers please follow the instructions below. *#→password→31→Tel Num.1*→Tel Num.1→Func Key *#→password→32→Tel Num.2*→Tel Num.2→Func Key *#→password→33→Tel Num.3*→Tel Num.3→Func Key *#→password→34→Tel Num.4*→Tel Num.4→Func Key *#→password→35→Tel Num.5*→Tel Num.
Please note that you have to enter the desired number twice. The number that you entered will need to match. If the numbers do not match then the unit will beep 3 times. If the numbers match then you will hear 2 beeps. To remove the phone numbers please follow the instructions below.
4.10.1 Arming the AX54 Siren Mode In Siren mode, when the motion sensors are triggered, it will emit a high pitched continuous beep, until the unit is disarmed. To activate Siren mode enter the following: *#→password→01->Arming Key Silent Mode In Silent mode, when the alarm is triggered the high pitched continuous beep will not sound making the intruder unaware that the alarm has been triggered, although SMS / Calls will be sent.
Stay Mode Occasionally you may want to alarm only a certain part of your house, and this can be achieved by using Stay mode. Please note that Zone 4 will only be triggered when using stay mode. In Stay mode, you can activate your alarm so that any motion in zones one, two or three will not trigger the alarm, but if there is any movement in zone four then the alarm will be triggered. In Stay mode you can choose whether the device emits a beep or stays silent when the alarm is triggered.
4.10.2 Disarming the AX54 When disarming the AX54, you can disarm in multiple ways, and these are described below. Normal Disarming To disarm the AX54 in a normal manner enter the following: *#->password->05->Arming Key Normal disarming Duress Disarming If you are forced to disarm the unit under duress, then SMS / Calls will still be made to the numbers that are stored in your device.
Remote Disarming You can also disarm the AX54 remotely via SMS. To do this the mobile number that you use to disarm the AX54 will need to be programmed as one of the three SMS numbers. To disarm the AX54 by SMS you will simply need to send a text message saying ‘Disarm Alarm’ to the number that corresponds to the SIM that is placed in the AX54. 4.11 Entry / Exit Delay You can modify the entry / exit delay to suit your needs. 4.11.
4.11.2 Exit Delay No Exit Delay 30 Seconds 60 Seconds 90 Seconds 120 Seconds - *#→password→60→Func Key *#→password→61→Func Key *#→password→62→Func Key *#→password→63→Func Key *#→password→64→Func Key 4.12 Panic Button Your AX54 features a panic button, that when pressed will immediately activate the siren, as well as alerting your friends and neighbors via SMS and Calls. To activate the panic button simply press the ‘PANIC’ button which is located on your main unit.
4.13 Factory Reset If your unit malfunctions or develops any form of software fault then it may be necessary to perform a factory reset.
5 Operating Specifications For ASK 433MHz，the Main Unit is only for RX function without TX function, and Motion Sensor (AI100) is only for TX function without RX function 5.
Maximum output power Channel Spacing 30KHz Channel Band width : 1.23MHz 300mW (24.7dBm) RSSI Sensitivity and Dynamic Range : -104dBm ~ -25dBm < FER = 0.5% Carrier spacing PCS 1900 Band Frequency Carrier spacing Maximum output power TX: 1850MHz ~ 1910MHz RX: 1930MHz ~ 1990MHz Channel Spacing : 50KHz Channel Band width : 1.23MHz 300mW (24.
RSSI Form Factor Dimension Antenna CDMA Sensitivity and Dynamic Range : -104dBm ~ -25dBm < FER = 0.5% Molex connector 80PIN 36.2*30*3.
CALL number Zone number Power adapter Battery ASK 433Mhz Band Frequency Carrier spacing RSSI Working Temperature Storage Temperature Humidity 5 sets phone number 4 zones 5V/2A 9V 433.82Mhz-434.02Mhz 0.
5.2 Motion Sensor (AI100) AP Detection mode Key Antenna Detection range LED Key Tamper switch Battery ASK 433Mhz Band Frequency BS0001 Passive infrared signal Molex connector 80PIN ASK433M Spring antenna 6-8m Red & Green Not support Support 9V 433.82Mhz-434.
Carrier spacing RSSI Working Temperature Storage Temperature Humidity 0.
AXESSTEL ALERT PRODUCTS CONSUMER WARRANTY AND LIMITATION OF LIABILITY THE AXESSTEL ALERT PRODUCT THAT YOU HAVE PURCHASED, WHEN PROPERLY INSTALLED, CAN BE USED TO DETECT MOTION IN A SPECIFIED AREA AND PROVIDE AN ALERT TO TELEPHONES OR PERSONAL DIGITAL ASSISTANTS THAT YOU SPECIFY. THE PRODUCT IS DESIGNED SOLELY TO PROVIDE AN ALERT. IT DOES NOT PROVIDE SECURITY, OR PREVENT INTRUSION, THEFT OR CRIME. THE PRODUCT IS NOT A SECURITY SERVICE, ALERTS ARE SENT ONLY TO THE DEVICES YOU SPECIFY.
IF AXESSTEL CANNOT CURE ANY DEFECT ON COMMERCIALLY REASONABLE TERMS, AXESSTEL SHALL REFUND THE VALUE OF THE NON-CONFORMING PRODUCT WITHIN FORTY- FIVE (45) DAYS.
COMPONENTS. ANY LIABILITY OF AXESSTEL TO YOU, AND YOUR SOLE AND EXCLUSIVE REMEDY, FOR ANY CLAIM ARISING OUT OF THE USE OR PURCHASE OF THE PRODUCT (WHETHER IN CONTRACT, TORT, OR OTHERWISE) WILL NOT EXCEED THE PURCHASE PRICE PAID FOR THE PRODUCT WHICH IS THE SUBJECT OF SUCH CLAIM OR CAUSE OF ACTION. NOT INSURANCE. AXESSTEL IS NOT AN INSURER AND IS NOT RESPONSIBLE FOR ACTS OR OMISSIONS OF OTHERS OR FOR EVENTS BEYOND ITS CONTROL.
FCC STATEMENT: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. ITS OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: THIS PRODUCT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
—REORIENT OR RELOCATE THE RECEIVING ANTENNA. —INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER. —CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE RECEIVER IS CONNECTED. —CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP. CAUTION: CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
