UTM-300 -1- 7/10/2019 SENTINEL-SENSE UTM-300 Installation & Operation Manual - 041520
UTM-300 -2- 7/10/2019 COPYRIGHT ACKNOWLEDGEMENTS The contents of this document are the property of Applied Wireless Identifications Group, Inc. (AWID) and are copyrighted. All rights reserved. Any reproduction, in whole or in part, is strictly prohibited. For additional copies of this document please contact: AWID 18300 Sutter Blvd Morgan Hill, CA 95037 http://www.AWID.
UTM-300 -3- 7/10/2019 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
UTM-300 -4- 7/10/2019 The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in this manual.
UTM-300 -5- 7/10/2019 I NDUSTRY C ANADA COMPLIANCE This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
UTM-300 -6- 7/10/2019 toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID cannot be used on the final product.
UTM-300 -7- 7/10/2019 Table of Contents REVISION HISTORY....................................................................................................8 1 INTRODUCTION.......................................................................................................9 1.1 2 Special Features ................................................................................................ 9 SPECIFICATIONS ...........................................................................................
UTM-300 -8- 7/10/2019 REVISION HISTORY Version No. 1.0 1.1 1.2 Revised By Date AWID Engineering AWID Engineering AWID Engineering 3/2019 6/2019 7/2019 Sections Remarks Affected Initial version Updated with FCC ID,IC P.
UTM-300 1 -9- 7/10/2019 INTRODUCTION AWID's UTM-300 is a Radio Frequency IDentification (RFID) reader module capable of working with most leading passive UHF tags. The reader module comes with a unique combination of antenna port, small size, and low power consumption. Its primary functions are in asset management and tracking, and fleet management, i.e., embedded applications for PoS, printers and other portable devices widely used in these markets.
UTM-300 - 10 - 2 SPECIFICATIONS Input voltage Input current Protocol language Read range RF connectors Output power Transmit frequency Receiver frequency Hopping channels Channel spacing Hopping sequence Operating temperature range Output data formats Interface Connector Dimension 7/10/2019 +4.75 ~ +5.25 VDC 700 mA EPC Class 1 Gen 2 ~ 20 ft (6 m) antenna and tag dependent U.FL (UMC) SWR<1.2 @50OHMs +27 dBm max 902.60-927.40 MHz 902.60-927.
UTM-300 - 11 - 7/10/2019 2.2 CONNECTOR PIN ASSIGNMENT ANT ENBL RXD TXD LED GREEN LED RED VIN Antenna Port Power ON/OFF Signal, VDD for ON, GND for OFF (*) Serial Communication In (3.3V) Serial Communication Out (3.3V) Green LED Signal – Hi (2.5V) on Good Tag Read (blinking) Red LED Signal – Hi (2.5V) when Power On (constant visual) 4.75~5.25V (*): ENBL pulled high to enable module. Tied to power for Always-On applications. 2.
UTM-300 - 12 - 7/10/2019 2.4 INPUT VOTAGE/CURRENT Table below shows input current (in mA) with input voltage applied at different RF Power (Level Index) Settings. Index 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RF Output Power (dBm) 13.5 14.3 15.3 16.1 17.2 18.0 19.1 19.9 21.2 22.0 23.0 23.8 24.8 25.6 26.5 27.2 5V [A] 0.22 0.22 0.23 0.24 0.26 0.27 0.29 0.31 0.34 0.36 0.39 0.41 0.45 0.48 0.53 0.
