MSDV2611-O3-D0 26" 66cm HD LCD Television with Built in DVD Player USER MANUAL Thank you for purchasing this LCD TV. Before connection and operation of this product please read the manual carefully and completely. Please keep this manual for future reference. N294 Version 1.
Contents INTRODUCTION..............................................................................1 SAFETY AND WARNINGS............................................................. 2-4 BASE STAND ASSEMBLY INSTRUCTION..........................................5 WALL MOUNTING INSTALLATION GUIDELINES................................6 INSTALLATION...........................................................................7-12 REMOTE CONTROL.................................................................
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings, install in accordance with the instructions. 8) Do not install near any heat sources such as radiators, air conditioners, stoves, or other apparatus (including amplifiers) that produce heat.
SAFETY AND WARNINGS High voltages are used in the operation of this television receiver. Do not remove the cabinet back from your set. Refer servicing to qualified service personnel. Never stand on, lean on, or suddenly push the television or its stand. You should pay special attention to children. Serious injury may result if it falls. To prevent fire or electrical shock hazard, do not expose the television receiver to rain or moisture.
SAFETY AND WARNINGS CAUTION Never tamper with any components inside the TV, or any other adjustment controls not mentioned in this manual. All LCD-TVs are high voltage instruments. When you clean up dust or water drops on the LCD PANEL or CABINET, the power cord should be physically removed from the mains outlet. You may then wipe the TV with a dry soft cloth. Before thunder and lightning events arrive, unplug the power cord and antenna cord to prevent damage to your TV.
STAND INSTALLATION GUIDE This STAND INSTALLATION GUIDE is provided to help you easily install the stand. Please carefully follow Step 1 through Step 3. Open the box and find the parts Open the box and find the following parts. - Stand x1 pc - Screws x 4 pcs Screws Packing Stand TV Stand Packing Place the Stand on the TV 1. Place the TV with the display side down on a table or desk (flat, totally clean surface). 2. Place the Stand on the TV as shown below.
INSTALLATION For wall mounting with the optional bracket, please read the following instruction and the bracket instruction. Make sure qualified service personnel perform the operation. AWA bears no responsibility for improper mounting that results in accident or injury.
INSTALLATION ACCESSORIES AC Power Cord.........................1 Stand mounting screws.........................4 Infrared Remote Control............1 Wall mounting M4 screws......................4 User's Manual ........................ 1 Battery (AAA).......................... 2 FRONT PANEL 3 1 2 4 30 30 1 2 3 4 5 6 7 8 9 0 + + VOL CH _ _ 1: Remote control sensor. 2: Indicator LED: GREEN RED = POWER ON. = STANDBY. 3: Key board (on side of TV).
INSTALLATION KEY BOARD SOURCE MENU CH+ CHVOL+ VOLSTANDBY 1. SOURCE: Displays the input source Menu. 2. MENU: Displays the main MENU. 3. CH+/CHIn TV mode, press "CH+" or "CH-" to change the channel up and down. In MENU mode, press "CH+" or "CH-" to select items. 4. VOL+/VOLAdjusts the sound level. In MENU mode, press "VOL+" or "VOL-" to adjust the item that you have selected. 5. STANDBY Once the TV's main power switch has been activated, press this button to turn the unit ON from STANDBY mode.
INSTALLATION ANTENNA CONNECTION Note: Aerial connections: IEC(female). Input impedance: 75 unbalanced.
INSTALLATION CONNECTING TO PC STEPS: Be sure both the TV and computer are set to Power off. 1.Connect VGA and audio cable. 2.Connect the power cord. 3.Power on the TV, switch the input source to VGA mode. 4.Power on the PC. This sequence is very important.
INSTALLATION PC PRESET PRESET MODE RESOLUTION V.Freq.(Hz) H.Freq.(KHz) 1 720*400 70 31.47 2 640*480 60 31.47 3 800*600 56 35.156 4 800*600 60 37.88 5 800*600 72 48.08 6 1024*768 60 48.36 7 1024*768 70 56.48 The above resolutions are the only ones guaranteed to be supported. Other resolutions up to 1920 x 1080 may also be supported, but this must be assessed by the user on a case-by-case basis. This is also subject to the limitiations of the computer’s video card.
INSTALLATION CONNECTING TO AV EQUIPMENT This TV provides two group of AV, one group of YPbPr (component video) inputs for convenient connection to VCR, DVD or other video equipment. Please refer to the owner's manual of the equipment to be connected as well. You can use the input terminals on TV set rear as follows.
REMOTE CONTROL Remote Control - TV section DVD/USB 1: POWER :Press to turn the unit on or off. 2: NUMERIC KEY :Press for direct access to channels. 3: TV MENU :Press to display TV Main Menu. 4: CURSOR :Press to scroll through the Menu. 6: VOL+/- :Press to adjust the sound level. 7: PIC :Press to switch between picture modes. 8: SLEEP :Press to set Sleep Timer. 9: REC :Press to record the TV program you are watching in DTV mode, 10: TV/RADIO :Press to switch between TV and Radio modes.
REMOTE CONTROL TELETEXT Teletext is an information system broadcast by certain channels which can be consulted like a newspaper. It also offers access to subtitles for viewers with hearing problems or who are not familiar with the transmission language (cable networks, satellite channels, etc.) Press: TEXT You will obtain: This is used to call or exit teletext modes. The summary appears with a list of items that can be accessed. Each item has a corresponding 3 digit page number.
OPERATION Installation Guide Please select an OSD Language Fran ais Magyar Country Cesky English Dansk Espanol Hrvatski Nederlands Portugues Deutsch E Italiano ~ ka Polski Pycck Norsk Australia Bulgaria Denmark Germany Austria Croatia Finland Greece Luxembourg Belgium Czech France Hungary Netherlands OK Italy OK This screen only appears when the TV is turned on for the first time, or reset to factory settings. You can choose language, country and auto tuning programs.
OPERATION 2).DTV Manual tuning: You can select a DTV channel then find the program in this channel. Press to select the channel, then press OK to search the programs . NOTE: The Bad Normal Good bar graph on this screen shows signal intensity during DTV reception only. _ DTV Manual Tuning VHF CH 5 + Press OK to search Bad Nomal Good 3). ATV Manual tuning : You can change the sound system, search the analog TV channels and fine tune them, then store the channels you selected.
OPERATION 5). Signal Information: Displays the signal information in DTV (digital TV) mode only. 6). Software Update: WARNING: Do not attempt to use this option unless you have a valid software program for the MSDV2611-O3-D0 TV stored on a compatible USB drive, and the drive is connected to the TV. Please remove the antenna cable from the TV RF port, go to the channel Menu, select " Software Update (USB) " and press OK to run the software update. 2. PICTURE MENU The second item of the MENU is PICTURE MENU.
OPERATION 5.OPTION MENU To enter the Option Menu, press MENU button and then press or buttons to select the Option Menu. Once in Option Menu, press or buttons to select the settings you wish to adjust. Press MENU button to return to the Main Menu. < OPTION OSD Language English Audio Languages Subtitle Languages Country Australia PVR File System Restore Factory Default > NOTE: Restore Factory Default will clear all the programs and password.
OPERATION FACTORY RESET NOTE: If you wish to reset your TV, please select the Restore Factory Default option, this will clear all settings. 6.LOCK MENU To enter the LOCK Menu, press MENU button and then press or buttons to select the LOCK Menu. The default password is 6666. Please set a new password so it is easy to remember. Follow the on screen steps to set your new password.
OPERATION 8.EPG Menu (Electronic Program Guide). The EPG Menu is used to look at what is being broadcast by DTV stations. After you turn the TV on and select the DTV input, your TV will commence receiving EPG data progressively over a period of time (typically up to half an hour, depending on the number of stations being received). Press the EPG Button to access the EPG Menu. You will receive detailed program information of the channel you are currently watching as well as programs in the near future.
OPERATION 9. PVR function 1). Prepare to record the program From OPTION MENU enter into the PVR File System and choose "check PVR File System". Click "OK", and wait until "checking" changes into "Success". Note: please check the result marked "Speed". If it is "HD support", that means the speed of your USB device is suitable for time shift and record functions. If not, please format the device, to make sure the USB device is capable of handling the recording functions.
OPERATION Format disk Format disk Format disk Do not unplug USB device. Warning! All data will be lost. Formatting,please wait Start Exit When the Format process has finished, you can then run the “Check PVR File System” option to show the speed ability of your USB storage device. Press EXIT to return to TV mode.
OPERATION 10. Timeshift function Prepare to record the program This TV allows you to pause and record the currently watched digital TV program to a USB storage device, and to resume viewing at the point where it was paused. NOTE: Formatting a USB 2.0 storage device will be needed. Save the original data on your USB device before formatting. All the data stored in the USB device will be erased after formatting.
OPERATION 11. Digital Media Player (DMP) To play and view low data-rate USB media files as well as DTV recordings made using this TV, use the DMP function that is accessible from the Applications Menu. For playback of high data-rate media files the use of an external Media Player is recommended. USB 2.0 PHOTO MUSIC MOVIE TEXT Please make sure that the USB device is plugged in the slot. There are four media types that can be selected, such as Photo, Music, Movie, and Text.
DVD OPERATION DVD SIDE PANEL 9 Dolby Digital Multi-angle 32 USB SD/MMC/MS Disc data side NEXT PREV STOP PLAY/PAUSE Disc label side facing you KODAK picture CD Subtitle choices 8 OPEN/CLOSE MP3 files on CD-R/CD-RW USB In DVD mode when no disc is playing, insert a USB drive (or an MP3 player with USB interface) into the USB socket. Press the DVD/USB button on the Remote Control unit, and use the / keys to select USB mode for playing MP3 or JPEG files.
DVD OPERATION SYSTEM SETUP MENU OPERATION Press the SETUP button on the remote control, the SETUP MENU will be displayed. After accessing the setup menu, press the direction buttons for up and down movement to select an item desired, and press RIGHT direction button to select the SUBMENU item. Then press the ENTER/OK button to confirm. Press LEFT direction button return to the menu of upper level. To exit the setup, press the SETUP button again.
DVD OPERATION MP3/WMA/JPEG PLAYBACK PICTURE CD PLAYBACK The PICTURE CD disc has such a directory structure as shown in the following picture. The MP3/WMA disc has such a directory structure as shown picture above. Press Direction key to choose the root directory and then press ENTER/OK button to enter into the sub directory. Press Direction key to choose the desired track and then press ENTER/OK or PLAY to enjoy the music or movie.
DVD OPERATION Function Buttons OPEN/CLOSE To open the disc tray, press OPEN/CLOSE; To close the disc tray, press OPEN/CLOSE again. SUBTITLE Press the button to choose different captions(Requires support from disc) GOTO For DVD discs, press the button to choose the desired title and chapter andsearch the desired title time and chapter time.For Super VCD,VCD,CD discs, press this button to search the desired disc time and track time and choose the desired track.
DVD Trouble shooting If you have any questions, please consult the troubleshooting guide below: REMOTE NOT WORKING NO PICTURE OR SOUND Ensure the power button is on. Make sure the Main unit s POWER button is on Ensure the power outlet is operational. Ensure the remote batteries are working. Ensure the power cord is not damaged. Point the remote control directly at the player s Ensure the power plug is connected IRsensor. firmly to the outlet.
TROUBLE SHOOTING Trouble phenomenon Symptom Picture Inspection Check Audio Snow Noise antenna position, direction or connection Ghost Normal audio antenna position, direction or connection Interference Noise electronic equipment, car/ motorcycle, fluorescent light Mute Volume (check if mute is activated or if the audio system connections are not correct) Normal Picture Mains Power cord is not inserted Mains Power switch is not activated Contrast and brightness/volume setup Press Power/Stand-
INTRODUCTION LCD : Viewing Picture Size(diagonal) 26"(66cm) Resolution 1366x768 Aspect Ratio 16:9 Display colours 16.7M Brightness 450 cd/m 2 Contrast ratio 800:1 Response time 5 ms View angle 160 (H)/150 (V) TV: TV system DVB-T decode DVB-T de-modulation Digital TV: DVB-T Analog TV: PAL Audio: MPEG2 Audio Layer I&II Video: MPEG2 Transport MP@HL Demodulator : COFDM OFDM Mod.