Model : SC101
Specifications SC101 Before Use Precautions……………………………….... 1 Scale Components………………………... 2 Error Displays..…………………………..... 3 Installing(or Replacing) Batteries …….... 4 Operations Measurement weight……….………………6 Wireless connection…………….………… 8 References Specifications……………………………… 9 Maintaining the Scale……………..……... 9 FCC Staeement.................................
Precautions ! Please read this booklet before using your scale. ! Do not place your scale on a soft, wet or slippery floor.It is recommended that the scale be used on a solid level surface, such as tile, wood, or laminate flooring. ! Place your scale on a solid level flooring surface. Your scale contains delicate, high-precision parts. Avoid extremes in the temperature, humidity, direct sunlight,shock , moisture and dust. ! Do not disassemble repair, or remodel the scale.
Indications for use ! This scale is designed for indoor use to measure the weight.
! The following measurement can be selected by slide switch and are classified into two categories WEIGHT MODE and WEIGHT CONNECTION MODE, you have choice to select and have your weight displayed in KG or LB. ! The scale has an “automatic- power-off” function to turn off in about sixty seconds after non-operation.
Installing (or Replacing) Batteries Caution: ! Insert the battery with the positive (+) and negative (-) terminals properly aligned with the corresponding symbols in the battery compartment. ! Improper installation of the batteries may cause battery leakage. ! Replace all four batteries with new ones, when “Lo” symbol is displayed. ! Do not mix used and new batteries. It may result in damage to the scale or shorten battery life.
Steps for Installing (or Replacing) Batteries 1. Remove the battery compartment cover on the underside of the scale by gently pushing on the arrow and lifting the cover backward. 2. Place four new batteries with the positive (+) and negative (-) terminals properly aligned with the corresponding symbols in the battery compartment. 3. Replace the cover by sliding it into the compartment and gently pressing into place.
Measurement Weight Measurement Your Weight 1. Slide switch to correct Mode Example A: Set the slide switch to “BLUETOOTH ON”, Tap on the scale,the scale will calibrate and display . Bluetooth indicator light to flash, Means Bluetooth connection is open. (Concrete operation please look at in wireless connection) B. Set the slide switch to “BLUETOOTH OFF”,Tap on the scale, the scale ill calibrate and display .
Step on the scale and position your feet in a manner that will distribute your weight evenly over the entire scale platform. The LCD display will flash two times, then the display will show your weight. Stand still while reading the display. Now you step off the scale, the display will show 0.00kg/0.00lb,You can measurement your weight again. (Caution: If you remain standing on the scale or step off the scale without sixty seconds after your weight has displayed and then turn off automatically).
Wireless Connection 1. Turn the Scale to the back side. 2. Turn on the bluetooth switch (From “0” to “1”), while the device is performing an inquiry to find other devices to which to connect, the LED on the front side of the Scale will be quickly flashing. When the device connects successfully to health Monitoring devices, such as a computer or a mobile phone, the LED is keeping on shining. At the end of the measurement, your Scale will be sent to your health monitoring device. 3.
Specifications SC101 Digital display Maximum capacity Minimum display Bluetooth connection Power source batteries Battery life Liquid crystal display, 38mm character height 200kg/440lb 0.05kg/0.11lb BlueMod+B20 ( Stollmann E+V GMBH)) Four type AAA (1.5 volt X 4, included) Approximately 1000 Measurements 5℃~35℃,30~85%RH Operation Environment Storage & Transportation Environment -20℃~60℃,10~95%RH Specifications are subjects to change without prior notice and any obligation on the part of the manufacturer.
FCC Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
EC REP EU Representative: Golden Star Computer (UK) Ltd., Unit 39, Rainbow Industrial Estate, Trout Road, West Drayton, Middx. UB7, 7RN, United Kingdom AViTA Corporation 9F, No.78, Sec.1, Kwang-Fu Rd., San-Chung, Taipei County, Taiwan No.