USER MANUAL TC9485UM Rev.
Table of Contents THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. 1. Unpacking 2 2. Product overview 3 3. Installation & Usage 4 3-1. Display 4 3-2. Installing the Battery 5 3-3. Removing the Battery 6 3-4. Charging the Battery 7 3-5. Installing Belt Clip 8 3-6. Stock Installation 9 3-7. Peel Mode 10 3-8.
2. Product overview 1.
3. Setting Up the Product 3-2. Installing the Battery 3-1. Display Button Name function Paper Feed/ Down button Advances the supply. Clears error message. Moves down through menu options. Enter button Selects the highlighted menu option. Up button Moves up through menu options. Power button Turns the printer on and off. Press to turn power on. Press for three seconds to turn power off. Wakes the printer from sleep mode. Remove the battery door. Insert the battery as shown. 1 2 NOTE 1.
3-3. Removing the Battery 3-4. Charging the Battery ② LED ① Remove the battery door. Lift out the battery. 1. Turn off the printer. 2. Be sure that the AC plug is correct. If AC plug is wrong, change the plug to the correct one. 3. Open the DC jack by pulling on the rubber cover and insert DC jack into the printer. 4. Plug the AC plug into an electrical outlet. 5. The charge indicator LED (located on the AC charger as shown) shows red or green according to the status.
3-5. Belt clip Usage 3-6. Stock Installation Insert screw into belt clip. 1 2 Open the Paper cover by pressing the Open button and set the width of paper guide by turning the knob with finger. 1 2 3 4 Tighten the screw with driver as shown. NOTE Adjust the width of paper guide if needed. Put the stock in so it unrolls from the bottom. Remove the stock core when it is empty. Pull a short length of stock out of the printer. Use two hands to close the cover until it clicks into place.
3-7. Peel Mode 3-8. Shoulder Strap Installation Peel Mode With a roll of stock installed, slide the peeler body towards the back of the printer. Non-Peel Mode Lift the peeler wing and slide the peeler body towards the front of the printer. 10 Optional Push the peeler body until you see two complete triangles. Press the feed button. Insert the strap into the hook of the printer. 1 2 3 1 2 1 2 Press the feed button. Place the end of the strap into the hook of shoulder strap.
3-9. Diagnostic Test The sample of self test printout Turn off the printer. Press and hold the feed button and power button. 1 2 3 NOTE 1. For Hex Dump mode, do steps 1-2 then press the feed button. 2. After printing ASCII pattern, the diagnostic test is complete. 3. If the feed button is not pressed to go to Hex Dump mode, the printer exits diagnostics after three seconds.
4. Peripherals Connection This product can communicate with other devices using Bluetooth, WiFi (802.11b/g), or a USB/Serial cable. 4-2. Interface Cable Connection 4-1. Wireless Communication USB Serial 1. Printer can connect to a PDA or PC for wireless communication. 2. Your PC must support Bluetooth or WiFi (802.11b/g) to connect to the printer. NOTE Refer to the System Administrator Guide for more information. 1. Connect the USB or Serial cable to the cable connector on the printer.
5. Printer cleaning If the interior of the printer is dusty, printing quality can be lowered. In this case, follow the instructions below to clean the printer. 5-2. Platen Roller Cleaning 5-1. PrintHead Cleaning 1.Clean the platen roller with a clean soft cloth moistened with isopropyl alcohol or a cleaning pen. 1. Use an applicator swab moistened with an isopropyl alcohol to clean the print head and remove any dust. 2. Turn the platen roller with your finger to clean the entire surface. 2.
6. Printer Specification 6-1. Specification Printing Method Direct Thermal Printing Speed 80mm/sec Resolution 203 DPI X 203 DPI Character Barcode One-Dimensional Barcodes Two-Dimensional Barcodes Stacked OneDimensional Barcodes AC100~240V, 50/60 Hz output 8.4V , 800~1200mA Battery type Li-ion ALPHA NUMERIC Character, Extension Character output 7.4V, 18.
7. CPCL Command Compatibility NOTE Compatible Compatible with only commanders provided by the manufacturer.
8.
Command 24 Compatibility Command Compatibility ^BX ○ ^ID ○ ^BY ○ ^IL ○ ^BZ ○ ^IM ○ ^CC ~CC ○ ^IS ○ ^CD ○ ~JR ○ ^CF ○ ^JS ○ ^CI ○ ~JS ○ ^CT ~CT ○ ^KL ○ ~DF ○ ^LH ○ ~DG ○ ^LL ○ ^FB ○ ^LR ○ ^FC ○ ^LS ○ ^FD ○ ^LT ○ ^FH ○ ^MC ○ ^FN ○ ^MD ○ ^FO ○ ^MN ○ ^FP ○ ^PM ○ ^FR ○ ^PO ○ ^FS ○ ^PQ ○ ^FT ○ ^PR ○ ^FV ○ ~PR ○ ^FW ○ ^PW ○ ^FX ○ ^SC ○ ^GB ○ ^SD ○ ^GC ○ ^SF ○ ^GD ○ ^SL ○ ^GE ○ ^SN ○ ^GF ○ ^SO ○ ^GS
Command 26 Compatibility ~TA ○ ^XA ○ ^XF ○ ^XG ○ ^XZ ○ ^ZZ ○ 27
