. Serf, te .. 1% Sen SEW DO TECH £0. LT. Eden Bn Ben Rev. 1.
A RISK OF EXPLOSION IF BATTERY 15 REPLACED BY AN (INCORRECT TYPE, DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION Disposal of Old Electrical &Electronic Equipment{Applicable in the European Union and either European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of IE electrical and electronics equipment.
1. Unpacking 7. Product overview Standard Front DISPLAY 2 Battery Belt Clip ee SERIAL Roar USB Cable co BATTERY COVER 5 BELTANE a oS common FL] as Optional Ax i.
3, Setting Up the Product 3-2. Installing battery 3-1. Control Panel Usage Paper Feed/ Advances the supply. Clears emir message. <7 | Down Hutton | Moves down through menu options. J Enter button | Selects the highlighted menu option. A Up button Moves up through menu options. Turns the printer on and off. Press for two seconds to turn & Power button | power on. Press for three seconds to tum power off. Wakes the printer from sleep mode.
3-3. Battery remove! Remove the battery door. Lift out the battery. 3-4. Battery Charging 1. Turn off the printer. 2. Be sure that the AC plug is correct. if AC plug is wrong, change the plug to the correct one. 3. Pen the DC jack by pulling on the rubber cover and insert DC jack inch the printer. 4. Plug the AC plug into an electrical ovulate. B. The charge indicator LED {located on the AC charger as shown) shows red or green according to the status.
3-5 Usage of Cigar Jack Charger 3-6. Belt clip Usage Optimal Insert screw inch bet clip. Connect the vehicle charger to the printer. 2 ne 24V LAY 081248 NOTE Connect the vehicle charge: (0 he orient, Tighten the screw with driver as shown.
3-7. Roil Paper Installation Open the Paper cover by pressing the Open button and set the width of paper guide by turning the knob with finger. Put the stock in so if unrolls from the bottom. Remove the stock core when it is empty. Pull a short length of stock out of the printer. Close the cover. Press the Feed Key once to arrange the paper. 3-8. Peel Mode With 2 roll of stock installed, side the peeler body towards the back of the printer. Press the feed button.
3-8. Shoulder Strap Installation Cotton 2 ~~ Br 3-10. Leif Test ) Turn off the printer. Press and hold the feed Insert the strap into the hook on the printer. button and power button. NOTE Place the end of the strap into After pulling out the end of the The information label prints. the hook of shoulder strap. strap tightly, put it into the clip 10 be fastened.
The sample of self test privation HE unl Week Errol ESL man Ca al Dada aided Bait nave insane Been mi a] God ann Bali wa Hay He nue Big fr ll LE Orion i Bal aid naan Br boor] Sir mask ss idiotic Heat (aad MER ER Pia SEER satiable wi MEE GE bade anh i ER Lipton initial installation or for troubleshooting, you can run the diagnostic test fo get informational about: Firmware version, emulation, code page, sensor settings, interface settings, fs.
5 Printer cleaning 4-2. Interface Cable Connection if the interior of the printer is dusty, printing quality can be lowered. In this case, follow the instructions below to clean the ringer. 54. Print Head Cleaning 1. Use an applicator swab moistened with an prophylaxis alcohol to clean the print head and remove any dusts. 2. Once cleaning is complete, allow the printer fo dry then install the stock and close the cover. Serial i 1. Connect USB or Serial cable into the cable connector on the printer.
FCC information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: {1) This Device may not cause harmful interface, and {2) This device must accept any interference received, including interference that may cause undesired operation. This Class [B] digital apparatus complies with Canadian ICES-003. Cet parallel meringue de la class [B] est conform a la norm NMB-0D3 du Canada.