Electric projection screen Avers Contour Tension (models above 2,1m picture width) User’s manual Read these instructions carefully before operating the screen.
Dear Customer, Thank you very much for the purchase of our product. The manual booklet contains all operation information you may require to install properly and operate the screen. We hope it will help you to get the most performance and enjoyment of yournew screen. Enjoytime with the AversScreens product. SAFETY INFORMATION NOTICE: Important safety information. Follow the instructions described in the operating manual for safety reasons.
1. SAFETY RULES SAFETY INFORMATION NOTICE: Important safety information. It is important for the safety of persons to follow these instructions. After reading the manual, please save it just in case of need in the future Do not allow children to play with the fixed controls (remote control). Keep the remote control unit out of reach of children. Frequently examine the screen installation for imbalance and signs of wear or damage to cables. Do not use if repair or adjustment is necessary.
2. Product specification Electrically rolled projection screen designed for fixed installation at projection systems for business presentations and/or home cinema applications. Side edges of the projection surface are wire tensioned to guarantee better flatness and improove picture quality. Best picture quality can be reached based when the selection of the projection surface type and size will be optimal for the, projection device (projector) and projection conditions at the planed installation.
Dimensions of projection screens. Picture area Viewing area width size [cm] [cm] 240 270 300 240 x 135 240 x 150 240 x 180 240 x 135 240 x 150 240 x 180 270 x 151,9 270 x 168,8 270 x 151,9 270 x 168,8 270 x 202,5 300 x 168,8 300 x 168,8 350 x 187,5 300 x 225 Screen aspect ratio 16:9 16:10 4:3 16:9 16:10 4:3 16:9 16:10 16:9 16:10 4:3 16:9 16:9 16:10 4:3 Screen case size W x H x D [cm] Projection fabrics max.
Contour 24xxx 27xxx 30xxx D[mm] 2948 3248 3748 d[mm] 191 191 191 Pic.1 Installation of the rods and anchors in the ceiling Pic.3 Screen module installatiuon Pic.2 Ceiling modul installation Pic.4 Masking module installation - Modify the recessed ceiling checkerwork to create rectangular whole of 106 x W+191 mm dimensions, (W - screen fabrics width in milimeters). Bottom flange of the properly installed ceiling module should be surfaced with the ceiling checkerwork.
3.3. Screen installation in the cardboard-plaster recessed ceiling. - Trace the shape of the ceiling module installation whole. Cut out the whole in the recessed ceiling according to the traced shape. - Slot up the ceiling module into the prepared whole and fix it with the installation springs. Contour 24xxx 27xxx 30xxx D[mm] 2905 3205 3705 Pic.5 Ceiling module installation slot preparation Pic.7 Screen module installation Pic.6 Ceiling module installation Pic.
3.4. Electric installation. ATTENTION: Electric installation work should be carried out by a certified electrician. - Lead out the power cables to the place of installation of the wall switch and between wall switch and screen. - Screen power line should be fused with 1A fuse. - Switch off the screen power line during installation work.
Tensioning wires were setup during screen manufacturing optimally. It would be necessary to modify the power of the tensioning wires after few years of screen use. Finetuning could be performed with 2mm hexagonal wrench applied into the regulation holes located at bottom bar end caps. Deterioration of projection surface flatness wil be affected as a result of improper finetuning of tensioning wires. Waves at the projection surface will cause problems with picture quality in case of geometry and sharpness.
5. Warranty conditions 1) Avers screens warranty period is 24 months from the date of purchase confirmed with the original purchase invoice. 2) Extended warranty period for electric engine is 60 month. 3) Surety commits to fix free of charge any failures (component or production defects) of the product which appear during warranty period.
Manufactured after 13.08.2005 This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. Disposing of this product correctly will help to save valuable resources and prevent any potentialnegative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point.