Italiano Game Capture HD II C285 English Français Deutsch Italiano Español Português User Manual
European Community Compliance Statement Class B This product is herewith confirmed to comply with the requirements set out in the Council Directives on the approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive (EMC) 2004/ 108/ EC, Low Voltage Directive (LVD) 2006/95/EC and Energy-related Products Directive (ErP) 2009/ 125/ EC. Responsible manufacturer: AVerMedia Technologies, Inc. No. 135, Jian 1st Rd.,Zhonghe Dist.
Responsible manufacturer: AVerMedia Technologies, Inc. No. 135, Jian 1st Rd.,Zhonghe Dist., New Taipei City 23585, Taiwan TEL: +886-2-2226-3630 USA Office contact: AVerMedia Technologies U.S.A. 47358 Fremont Blvd., Fremont, CA 94538 Technical Support: http://www.avermedia.com/avertv/Support/ WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) The mark of Crossed-out wheeled bin indicates that this product must not be disposed of with your other household waste.
Disclaimer & Copyright © 2013 by AVerMedia Technologies, Inc. All rights reserved. No part of this document may be reproduced or transmitted in any form, or by any means (Electronic, mechanical, photocopy, recording, or otherwise) without prior written permission of AVerMedia Technologies, Inc. Information in this document is subject to change without notice. AVerMedia Technologies, Inc.
Table of Content Chapter 1 1.1 Chapter 2 2.1 2.2 2.3 2.4 Package Contents ................................................................... 2 Other Items You Need ......................................................................... 4 The Unit Parts .......................................................................... 5 Front Panel .......................................................................................... 5 Infrared Sensor .......................................................
Introduction The Capture Box, a stand-alone video capture box specially designed for TV gamers, allows you to ® capture HD content up to 1080p from various video game consoles, such as PlayStation 3, Xbox 360 and Wii U. The Capture Box records HD gameplays directly to your hard disk drive (HDD) for later viewing and further editing, eschewing the hassle of setting up a PC nearby your TV set.
HDMI Cable User Manual Quick Guide Remote Control (Batteries Included) The accessories that come with the package may slightly vary depending on different sales regions. The Capture Box is made for record and capture media materials that are legally owned or licensed by the user only. Any violation of copyrights or other intellectual property rights is not allowed. AVerMedia regularly releases the latest version of firmware for the Capture Box.
1.1 Other Items You Need In order to fully enjoy the recording, the capturing functions of the Capture Box and the dedicated iPhone application, you will need to have the following items prepared: Item You need the item to… Storage Device Save recordings and snapshots. Play Station 3 AV Component Cable Connect with PS3 console. Router (DHCP IP Network Recommended) Pair up with GameMate. iPhone 4/ 5, 4s Use GameMate. Headset / Microphone Record live commentary.
Chapter 2 The Unit Parts 2.1 Front Panel The button panel found on the front of the unit provides quick access to commonly used functions. # Buttons Descriptions Record Press to start / stop recording. 1 Hold down the button for 4 seconds to force shut down the Capture Box Power 2 Press to turn the unit on 2.2 Infrared Sensor When using the remote control, aim it at the infrared (IR) sensor located at the front panel of the unit.
2.3 LED Indicator The LED indicators on the front of the unit show the device’s status.
Condition Storage space is low Source Record Power Solid green Glows at a slowly pace Solid green Flashes green continuously Device is not ready Problems like no storage/ no signal/ protected content Flashes green continuously Accepting a remote control command Flashes green once Press [F1] to obtain LED light indicator status. 2.4 Connection Ports 2.4.
2.4.
Chapter 3 The Remote Control The descriptions below show the deployment of the keys on the remote control.
# 1 2 3 4 5 Buttons Descriptions Press to turn the unit on / into stand-by mode. Press to access the main menu. Press again to exit. Press the navigation keys to move among options. Press OK to confirm a selection. Press OK to mark/ unmark segment in post- editing. Press to play the latest recorded file or view the last captured image. Press to start / stop recording. 6 Press to start playing the selected file.
18 Press to pause the playback. Press OK or Press to pause the recording. 19 Press to play the video in slow motion (1/2x). Press again to enter frame- by- frame mode (See Chapter 5 for details). 20 21 22 23 to resume playback. Press to fast-forward (2x, 4x, 8x, 16x, 32x). Press to go to the next page. Press to delete the selected files. Press to display the disk information. Press again to hide it.
Chapter 4 Installation & First Time Setup 4.1 Supported Resolutions The Game Capture HD II supports Component (YPbPr) and HDMI input resolution as follows: HDMI / Component (YPbPr) 480i/576i 480p/576p 720p (50 & 60Hz) 1080i (50 & 60Hz) 1080p (50 & 60Hz) The Game Capture HD II records the exact display resolution under most circumstances.
Estimated recording duration for different video quality settings: HD 1080p Video Quality Optimal (20 Mbps) Good (18 Mbps) Maximum Recording Length (15 Mbps) 1TB 100 hrs 110 hrs 125 hrs 2TB 200 hrs 220hrs 250hrs Optimal (20 Mbps) Good (15 Mbps) Maximum Recording Length (10 Mbps) 1TB 100 hrs 125hrs 200 hrs 2TB 200 hrs 250 hrs 400hrs Optimal (15 Mbps) Good (12 Mbps) Maximum Recording Length (10 Mbps) 1TB 125 hrs 150 hrs 200 hrs 2TB 250 hrs 300 hrs 400 hrs Optimal (7.
4.2 Hardware Installation Please follow the steps below to properly connect the Capture Box and your TV/ video game consoles. If you would like to install internal hard drive, install it before turning on the Capture Box. Make sure that the cables are firmly connected and that neither of the cables is loose. If any of the cables are loose or disconnected, there may be a loss of signal or screen color problems.
“PlayStation 3 Component AV Cable” and Wii Component Cable is NOT Included. Please purchase separately if needed. Step 3 Connecting the Device to Your TV Using HDMI Cable Connect one end of the HDMI cable to the HDMI OUT port on the rear of the device and the other end to the HDMI IN port on your TV. Step 4 Power on Your Game Console Turn on your game console.
Step 5 Install and Connecting the Power Adapter Slide the Power Adapter Outlet Module into the groove on the Power Adapter. Connect the Power Adapter connector to the DC-IN port on the rear of the device. Then plug the power adapter to a wall outlet.
Step 6 Connecting to the Network To automatically obtain time and other information, you need to connect the Capture Box to an Ethernet LAN. Make sure the LAN wire is well-connected before you continue to the next step. Meanwhile, a router which supports DHCP IP network is recommended for you to pair up the Game Capture HD II with your iPhone. It is recommended that you connect the Capture Box before running first time setup.
Step 8 Power on the Capture Box Press the power button on the front panel of the device. Or Use the power button on the remote control. The POWER LED indicator lights up green, when that the device is power-on. It is important that you power on/ off the Capture Box following suggested procedure .
Step 9 Check Video on TV screen Make sure that there is game console video content displayed on TV screen. If your TV is not displaying video properly, please check the followings: Supported resolutions vary depending on the TV in use. For details, please refer to the documentation that comes with your TV. Power off Capture Box and then make sure that the device is connected properly and with the proper cables. If there is still no video signal on TV, refer to FAQ section at www.avermedia.
4.3 Storage Device Installation The Capture Box supports 2.5 inch internal hard drive and external USB storage device. You can save the recorded files and snapshots either to the internal HDD or external one. 4.3.1 USB Storage Device Insertion Connect your portable USB hard drive to the USB port on the front of the Capture Box It is highly recommended to use a NTFS format hard drive instead of a flash drive to minimize the risk of recording failure.
To install the internal HDD: Step 1 Remove the HDD Lid Open the HDD lid on the bottom of the Capture Box. Step 2 Before Installing Internal HDD Use the measuring card to measure the height of your HDD (7mm or 9.5mm). Please refer to the Appendix C for the measuring card.
Adjust the rotary knob attached to the inner side of the lid to fit the height of your HDD. The default position of the rotary knob fits HDD with 9.5mm height. If you use HDD with 7mm/ 9.5mm height, rotate the rotary knob to the other direction. Using a 9.5mm HDD: Using a 7mm HDD: Step 3 Inserting the HDD Place the HDD on the slot with the sticker-side facing up and the HDD connector end facing to the left. Align and insert the HDD connectors all the way into the SATA connector.
Step 4 Replace the HDD Lid Place the HDD lid back and snap it into place. To remove the internal HDD: Step 1 Remove the HDD Lid Please wait until the HDD cools down completely (it takes approximately 10 minutes) before any attempt to remove it. Use your fingertip to flip open the HDD lid, located on the bottom of the Capture Box.
Lift off the lid and set it aside. Step 2 Removing the HDD Pull the HDD out in the direction of the arrow. Then lift the HDD out of the slot. Step 3 Replacing the HDD Lid Place the HDD lid back and snap it into place.
It is typical that after a hard drive is formatted, the actual disk space of the drive would be slightly less than its unformatted capacity. 4.4 Setup Wizard When the first time you power on the Capture Box unit, the setup wizard appears. The following steps guide you through the initial configuration process. Make sure to install a hard drive (internal or external) and to connect to the internet beforehand.
Step 2 A/V Pass Thru. It is suggested that A/V Pass Through to be turned ON. Step 3 (1) Reminder Make sure a NTFS-formatted hard drive is connected or installed to the device. (For details, see Chapter 4.2) Check the connection of network. Press OK to start setup. A router which supports DHCP IP network is recommended. Also, refer to Ch. 6.2 for Manual connection setup.
Step 4 (1) No Hard Drive Detected If you have not yet installed any storage device, install it before continuing the setup process. Then press to go to the previous screen and press OK to run disk checking process. Step 4 (2) Finishing Setup Wizard Once a NTFS-formatted hard drive is connected, a Settings Complete notice will be shown. You can start to record and take snapshot right away. Press OK to exit the wizard and start using Capture Box. The game screen then appears.
4.5 Video Output Settings for Game Consoles The Capture Box supports YPbPr / HDMI input resolution up to 1080p. 4.5.1 Video Output Settings for PlayStation 3 Step 1 Power on your PlayStation 3 console. On your console, go to Settings > Display Settings > Video Output Settings. Step 2 Select Component/D-terminal and confirm the selection. Then your TV screen goes blank immediately. Now use your TV remote to switch the TV input source to Component (YPbPr). The screen then comes back on again.
Step 3 Check ALL the resolutions. Confirm the setting. Step 4 Select Set Audio Output Settings. Select Audio Input Connector/SCART/ AV MULTI as audio output. Confirm the setting. 4.5.2 Video Output Settings for Xbox 360 Before resetting video output for XBox 360, make sure to properly connect the Capture Box with your Xbox 360. Make sure to power off both the Capture Box and your Xbox beforehand. Supported resolutions vary depending on the TV in use.
Power on your Xbox console. On your console, go to My Xbox on the dashboard and scroll all the way to the right to System Settings. Then select Console Settings > Display > HDTV Settings. Please set the audio output of all game consoles as auto. Although the Capture Box do not support DOLBY 5.1 and 24p resolution video/ audio format, you can still pass through these format while the Capture Box is off.
Chapter 5 Basic Operation This chapter guides you to record gameplay, capture images, add voice commentary to videos, and instantly play files. All the recorded files or snapshots will be saved to the default hard drive destination automatically. Please see Chapter 6 for details. 5.1 Record and Capture The Capture Box lets you record, capture and adds voice commentary to the videos. Instructions are given as follows. The Capture Box displays gameplay in real-time and standard mode.
Quick Snapshot During Gameplay - Press to capture current image. Long Press to activate continuous capture mode. The Capture Box will take 5 snapshots at one time. Instant Playback - Press to play the latest recorded file or view the last captured image. - Press to stop the playback. - Press ►to skip forward 30 seconds. - Press ◄ to skip backward 10 seconds. Image Capture During Video Playback Way 1: - Press to capture current image.
Disk Information Press then press OK to display the disk information. Press again to hide it. 5.2 Adding Commentary This section shows you how voice commentary is added to your video recording. Requirements for headset/microphone: Headset Connector: 3.5mm jack Microphone Frequency Response : 20-16kHz Impedance: 2.0 KΩ Working Voltage: 3V Connector: 3.5mm jack OSD Menu Descriptions Microphone On An OSD will be shown if you connected microphone/ to the Capture Box.
If headset or microphone is plugged in during the Wizard Setup, the sound can only be heard from your headphone and instructions on voice commentary will not be displayed. Therefore, plug in headset or microphone after you complete Wizard setup so as to follow the headphone/ microphone instructions. All commentary added will be mixed with the gameplay sound. Also, as long as the headphone is connected to the device, all your commentary and background sound will be recorded.
Chapter 6 OSD Menu Under the menu, you can check and manage both your recorded files and snapshots, and customize your preferences. 1 Remaining Time for Recording 3 Network Connection 2 Connecting to GameMate 4 Current Time OSD Menu Descriptions Basic Operation - Press to bring up the menu. - Press or to return to the game screen. - Use ▲/▼ to make selection on the menu and OK to enter a submenu. - In the submenu, use ▲/▼ to make selection and OK to confirm. Press previous page.
Press F1 to safely remove the storage device.. - *The upper left corner shows your current default storage device and available remaining recording 6.1 Media Studio You can check both recordings and snapshots captured by the Capture Box in “Media Studio”. Capture Format: Video MP4 (Codec: H.264 format with AAC audio) Image JPEG It is recommended that you view only videos and snapshots that are recorded by the Capture Box.
Video Playback - Press or OK to start playing the selected video. - Press or OK to pause the playback. Press or OK to resume playback. - Press to play the video in slow motion (1/2x). - Press to rewind at 2x, 4x, 8x, 16x, 32x speed. - Press to fast forward at 2x, 4x, 8x, 16x, 32x speed. - Press to play the file at normal (1x) speed when slow motion, rewind, or fast-forward is active. - Press to stop the playback.
OSD Menu Descriptions Select a Video - Select the file you would like to edit by using the navigation keys ◄/►/▲/▼. Edit/ Share Press F3 to edit or share the selected video. Change File Name Input your file name by using the navigation keys ▲/▼ to select characters, numerals or symbols. Use the navigations keys ◄/► to go to the next/ last character. Press F1 to switch between characters, numerals and symbols. - Press to go back to cancel the change you made. - Press OK to save the edited file name.
How to Edit An instruction on how to edit a video will be displayed, press OK to start editing. Edit Mode You can cut and recombine your selected video in Edit Mode. - To cut the video, you will need to create one or more segments within the video. - Step 1: - To locate a scene, use direction keys or to search the scene. You can also use navigation keys ▲/▼ to search scene by specific hour, minute, and second on the left hand side of the screen. - Press OK to mark or unmark the scene.
Preview - The Capture Box automatically recombines the segments you choose to keep during editing. Export - The estimated time varies by different storage disks. Refer export time to the actual use of your storage disk. - Press OK to export the video. - Press OSD Menu to continue editing. Descriptions Exporting… The bar in the middle shows the progress of video exporting and estimated time. - Click on to cancel exporting. - Click on to hide the exporting information.
Exit Press OK to exit from the editing mode. - Press to exit Press F1 to continue editing. OSD Menu Descriptions Share Videos on YouTube Use ▲/▼ to select the task you would like to undergo. Select ‘Share on YouTube’ to share your videos. Share On YouTube Before you share your recorded videos on YouTube, make sure you: 1. Built a YouTube account and also a personal channel. 2. Have your PC/ NB next to you if you activate two- step verification of your YouTube account.
- Press OK to continue uploading. - Press F1 to skip this reminder afterwards. Account Setup - Use ▲/▼ to select the task you would like to undergo. Press to go back to last level. Press OK to edit your email or password. Press F1 to save the change you made. - Edit Before Uploading - Press o return to the last page. - Press OK to start uploading. - Press F1 to set the privacy. Press F2 to change account. Uploading Complete You have successfully upload the video.
The recommended length of each video should be less than 1 hour. The Capture Box is made for record and capture media materials that are legally owned or licensed by the user only. Uploading videos that are protected by copyright and other laws is not allowed. YouTube may shut down the account for copyright protection reason. YouTube account verification is required when you upload video that are longer than 15 minutes. Refer to YouTube website for further details.
File Management User Interface: 1 A list displaying files located on the internal hard disk 2 A set of editing tools 3 A list displaying files located on the USB disk 4 Information display area Descriptions on Editing Tools: # 1 2 3 4 5 Buttons Descriptions Copy files to USB disk Copy files to internal hard disk Select all Deselect all Delete OSD Menu Descriptions English-44
Copying Files from Internal HDD to USB Disk Step 1: - On the left-side list, use ▲/▼ to highlight the file that you want to copy to USB disk. Press OK to select / unselect an item. - Select and press OK to select all files. - Select and press OK to deselect all files. Step 2: - Select and press OK to copy selected file(s) to USB disk. - Press to cancel copying the files in a progress. Step 3: - Press OK. Copying Files from USB Disk to Internal HDD works in the opposite way as above mentioned.
or Press on the remote and then press OK to remove the file from the list. - Press to cancel deleting the files in a progress. Step 3: - Press OK. USB Storage Device Removal In order to avoid data loss, it is highly recommended to safely remove your external storage device. Please follow the steps below: Step 1: Press on the remote control. Step 2: Press F2 to remove it.
6.3 Settings You can customize your preferences in “Settings”. OSD Menu Descriptions Basic Operation - Use ▲/▼ to select a preferred category. Press OK to make a selection. - Press Press to return to the previous page. to directly access the main menu. - Press F1 to safely remove the storage device. OSD Menu Descriptions Language Use ▲/▼ to select your preferred language. Press OK to confirm. OSD Menu Descriptions Display Mode The default mode is set as real-time mode.
Real-Time Mode Real-time mode lets you play games with zero delay. And it is best for FTG, STG, RAC, and other rhythm games. No recording or snapshot status will be shown on screen. All capture work will run in the background. However, if any problem occurs during the capturing process, OSD will automatically jumps out. - Press to check OSD and track capture status. Standard Mode In standard mode, on-going recordings will be shown in the upper right corner of the screen.
OSD Menu Descriptions Network Settings Use ▲/▼ to move among options. Press OK to confirm. Before setup, please make sure the Ethernet cable is well connected. Auto Setup (Recommended) : It is recommended to use Auto Setup to automatically obtain IP and DNS addresses. Manual Setup : Use Manual Setup to manually configure IP and DNS addresses. STEP 1: Use ▲/▼ to select an item for configuration. Press OK to confirm. STEP 2: Use ◄/► to move among options and ▲/▼ to select a number. Press OK to confirm.
PPPoE : Use username and password provided by ISP for connection. STEP 1: Use ▲/▼ to select an item for configuration. Press OK to confirm. STEP 2: Use ◄/► to move among options and ▲/▼ to select a character. Press F1 to switch among capital letters, lower cases, numbers, or signs. Press OK to save the setting. - Press to cancel and return to the previous page. Press to delete selected characters and the character to the right. STEP 3: Press F1 to save the settings and test the network connectivity.
Network Connectivity Test Once network setting is completed, a list of connection details will be displayed. Press OK to confirm. Current Network Information This page displays the current status of your network connection. If network is temporarily inaccessible, manually set up the time zone settings so that the videos and snapshots is named correctly. OSD Menu Descriptions Date and Time Use ▲/▼ to select an item for configuration. Press OK to confirm.
Date Format : Use ▲/▼ to select a preferred date format. Press OK to confirm. Auto Update : Use ▲/▼ to enable/disable automatic date and time update. Press OK to confirm. *To use this function, a network connection is required. Time Zone : STEP 1: Use ▲/▼ to move among options and select your area. Press OK to confirm. STEP 2: Use ▲/▼ to move among options and select your time zone. Press OK to confirm. Time Setup : Use ◄/► to move among options and ▲/▼ to adjust date and time. Press OK to confirm.
Daylight Saving Time : Use ▲/▼ to enable/disable Daylight Saving Time. Press OK to confirm. *To use this function, a network connection is required. OSD Menu Descriptions Disk Management Storage Destination Step 1: Select and press OK to change your current desired default storage device for both recorded files and snapshots. * indicates normal write speed of selected partition; indicates low write speed of selected partition.
Use ▲/▼ to move among options. Press OK to confirm. Press to switch from component and HDMI input sources. Video Input: Use ▲/▼ to toggle between various video input source options (Component / HDMI). / Press OK to confirm. Audio Input: Use ▲/▼ to toggle between various audio input source options (Stereo Audio/ HDMI). Press OK to confirm.
OSD Menu Descriptions A/V Pass Through: Use ▲/▼ to enable/disable A/V Pass Through. Press OK to confirm. *The default setting is set Off to yield to the power-saving regulation. If this function is enabled, Capture Box still output signal when the Capture Box is off. If this function is disabled, Capture Box does not output signal when the Capture Box is off. Color Range Setup Use ▲/▼ to toggle between off, limited, and full. Press OK to confirm.
Watermark Type: Use to ▲/▼ select from the listed watermark types. Press OK to save the change. - Press to go back to last level. Position: Use ▲/▼ to select from the listed watermark positions. Press OK to save the change. - Press to go back to last level. Display Scale: Use ▲/▼ to select the display scale. Press OK to save the change. - Press English-56 to go back to last level.
OSD Menu Descriptions Auto Save Use ▲/▼ to switch from enable or disable the Auto Save function. Recording/ Snapshot Video Quality: Use ▲/▼ to toggle among various video quality options (Optimal/ Good/ Maximum recording length). Press OK to confirm. Snapshot Quality: Use ▲/▼ to toggle among various snapshot quality options (Best /Better / Good). Press OK to confirm.
Live Commentary A short demonstration will be played in this section. Press OK to continue. Volume: Use ▲/▼ to move among options and ◄/► to adjust the volume. Press OK to save the setting. Press F1 to restore to the default setting. Sound Mode: Use ▲/▼ to select a preferred mode for mic recording. Press OK to confirm. Gameplayer Mode will automatically switch game sound output to your headphone. To ensure the optimal quality, please use both microphone and headphone for voice commentary recording.
OSD Menu Descriptions Firmware Upgrade Follow the steps below to upgrade the firmware via USB storage device: Step 1: To download the latest firmware binary package, please go to www.avermedia.com, and then enter the model name in Product Search field. Firmware file is available on the product information page. Step 2: Extract the files by unzipping the package. Copy the firmware files to the root directory of your USB storage device, and then connect it to the Capture Box.
Restore to Factory Settings Press F1 to restore to original factory settings. Press to abort the operation and return to the previous page. Product Information This page provides information about this product, including product name, model no., and firmware version. Press F1 to edit the display name. OSD Descriptions Name your own Capture Box. Press navigation keys select characters. Up and Down to Press navigation keys Left and Right to shift to the former or later character.
Chapter 7 Pairing Capture Box and GameMate by AVerMedia GameMate by AVerMedia is the dedicated app for smart phones. It allows you to use your smart phone as remote control. You are only a few steps from pairing up the Capture Box with GameMate. Please download GameMate by AVerMedia from app store first. To pair up successfully, make sure the Capture Box and GameMate share the same network. To do so, you will also need a wireless access point for GameMate.
Tap to input the provided four-digit pairing number correctly. You will see GameMate as shown left hand side when it successfully pairs up with Capture Box. You can also check the connection GameMate from the Menu. You will see sign on the upper level of the Menu. If the connection is lost, please restart the wireless AP or the Capture Box and try again.
Appendix A How to Set Your Gameplay Snapshot as PS3 Wallpaper Start to give your PS3 menu screen a fresh and personalized look to show how cool you are! Please follow the steps below to set the image captured by the Capture Box as your PS3 background wallpaper. Step 1 Remove your USB storage device from the Capture Box, and then plug it into your PS3 console via USB port. Power on your PS3 console. Step 2 On your console, go to Photo > USB Device.
Step 4 Use the right joystick to zoom in/out and left joystick to frame the image. When it is the proper size, press (Enter). Confirm with (Enter) if you are prompted to overwrite your current wallpaper. ○ ○ Step 5 Done! The snapshot that you have chosen is now set as your PS3 wallpaper. On your PS3 console, you can go to Settings > Theme Settings > Background to turn wallpaper on or off.
Appendix B Troubleshooting To download the latest firmware for the Capture Box: Go to www.avermedia.com. Enter the model no. (C285) in Product Search field. The latest firmware file is available on the “AP & Driver” section on the product information page. Hard Drive Problem Hard drive not detected Actions Make sure that the storage destination is properly set up. Go to Menu Settings Disk Management Storage Destination to set storage destination.
sure that the device is connected with the proper cables (See 3.1 Hardware Installation in user manual for details). Green screen color with buzzing noise: Screen color appears abnormal using component input Unsuccessful recording of HDMI-input-videos Blacken screen using HDMI input The recording is fast-forwarded or stopped when recording complicated gameplay frames in HD resolution (720p or above)? Make sure that the red and blue connectors do not come loose.
Poor quality of captured video Check video output settings of your game console. For PS3, set 1080p, 1080i and 720p as video output resolutions. If you only select 1080i, the screen resolution automatically goes to 480i when you play a game that supports 720p. (See 3.5 Video Output Settings for Game Consoles in user manual for details). Enable the “De-interlace” function of your media player before playback. Some media players cannot process the interlaced video (1080i / 576i /480i) well.
130415-0930 A recorded videos with commentary will be called: 130415-0930 (Mic) An edited recorded video will be named as : 130415-0930 (Edit-1) A videos that has been edited for the second time will be named as : 130415-0930 (Edit-2) An edited video with commentary will be named as : 130415-0930 (Mic-Edit-1) The Game Capture HD II detects all kinds of folder that built in your hard drive; as a result, it is likely that the destination is set to a non-standard folder, fo
Other Problems Actions Solutions are as follows: A. Power off the Capture Box if an internal storage disk is installed. Remove internal storage disk and power on the Capture Box. Connect the USB to your Capture Box to undergo FW upgrade. (*If you are using a SATA storage disk or the temperature of the hard disk appears high; please wait for 10 minutes for the hard disk to cool down.) B. Save the unzipped firmware file to the file root of your USB. C.
Appendix C Measuring Your HDD Height Before Installation English-70
Open Source Code Notice The following GPL executables and LGPL, MPL libraries used in this product are subject to the BSD/FreeBSD/ GPL/GPLv2/GPLv2+/GPLv3 with GCC/ RLE/jpeg/LGPLv2/LGPLv2.1/LGPLv2.1/ GPLv2/LGPLv2.
LGPLv2.1+ ldd/libc6/libthread-db1 LGPLv2+ libglib-2.0-0 libpng libpng12-0 MIT cocos2d-x/curl/e2fsprogs/fbset-modes/graphmagic/libcom-err2/libcurl4/libe2p2/libexpat1/libext2fs2/libformw/ libmenuw/libpanelw5/libss2/libtic5/libtinfo5/libxml2/ncurses/pointercal New BSD iperf OPENSSL openssl PD modutils-initscripts zlib libz1 AVerMedia Technologies Inc.
Table des matières Chapitre 1. Pièces de l’appareil ................................................................. 2 1.1 1.2 1.3 1.4 Panneau avant..................................................................................... 2 Détecteur infrarouge ............................................................................ 2 Indicateur LED ..................................................................................... 3 Ports de connexion ....................................................
Chapitre 1. Pièces de l’appareil Panneau avant Le panneau à touches se trouvant sur le devant de l’appareil fournit un accès rapide aux fonctions communément utilisées. Touches numérotées Descriptions Enregistrer Appuyez sur démarrer/arrêter l’enregistrement. 1 Alimentation (Power) Appuyez pour allumer l’appareil Maintenez le bouton enfoncé pendant 4 secondes pour forcer l'arrêt le Capture Box. 2 1.
1.3 Indicateur LED Les indicateurs LED sur le devant de l’appareil affichent le statut de celui-ci.
Condition Source Enregistrer Alimentation (Power) L'espace de stockage est faible Vert solide Brille lentement Vert solide Clignotement vert en continu L'appareil n'est pas prêt Problèmes tels qu'aucun stockage/aucun signal/contenu protégé Clignotement vert en continu Accepter une commande de la télécommande Clignote vert une fois Appuyez sur [F1] pour obtenir le statut du voyant LED. 1.4 Ports de connexion 1.4.
1.4.
Chapitre 2. La télécommande Les descriptions ci-dessous présentent les touches de la télécommande. # 1 2 Boutons Descriptions Appuyez pour allumer l’appareil/le mettre en veille. Appuyez pour accéder au menu principal. Appuyez à nouveau pour quitter. 3 Appuyez sur les touches de direction pour vous déplacer parmi les options. Appuyez sur OK pour confirmer une sélection. Appuyez sur OK pour marquer/enlever le marquage d’un segment en post-édition.
6 Appuyez pour démarrer la lecture du fichier sélectionné. Appuyez pour lire le fichier à la vitesse normale (1x) lorsque la fonction lecture au ralenti, retour ou avance rapide est active. 7 Appuyez pour arrêter la lecture. Appuyez pour arrêter l’enregistrement. 8 9 10 11 12 13 14 15 16 17 Appuyez pour le retour rapide (2x, 4x, 8x, 16x, 32x). Appuyez pour revenir à la page précédente. Appuyez pour afficher l’écran de réglage de la qualité de la vidéo/photo. Appuyez à nouveau pour quitter.
Chapitre 3. Assistant d’installatio Lorsque vous branchez votre Boîtier d’Acquisition pour la première fois, l’assistant d’installation apparaît. Les étapes suivantes vous guident tout au long de la procédure de configuration initiale. Assurez-vous que vous avez installé un disque dur (interne ou externe) et connecté le boîtier à Internet avant de démarrer la procédure.
Etape 3 (1) Rappel Assurez-vous que le disque dur branché ou installé sur le boîtier est bien formaté en NTFS. (Pour plus de détails, reportez-vous au Chapitre 4.2) Vérifiez la connexion au réseau. Appuyez ensuite sur OK pour démarrer la configuration. Nous vous recommandons d’utiliser un routeur qui supporte les réseaux IP DHCP. Veuillez vous référer au Chapitre Ch. 6.2 pour un réglage manuel de la connexion.
Etape 4 (2) Fin du Processus d’Installation Une fois qu’un disque dur formaté en NT)S est connecté au boîtier, un message de fin d’installation s’affiche. Vous pouvez commencer à enregistrer dès maintenant. Appuyez sur OK pour sortir de l’assistant d’installation et commencer à utiliser votre boîtier. Votre jeu apparaît à l’écran.
Chapitre 4. Fonctionnement de base Ce chapitre vous guide pour l'enregistrement de jeux en cours, la capture d'images, l'ajout de commentaires vocaux pour vidéos et la lecture instantanée de fichiers. Tous les fichiers ou photos enregistrés seront sauvegardés sur le DD par défaut automatiquement. Veuillez vous référer au chapitre 6 pour plus de détails. 4.1 Enregistrement et capture Capture Box vous permet d'enregistrer, de capturer et ajouter des commentaires v ocaux aux vidéos.
Aperçu rapide en cours de jeu pour capturer l’image actuelle. - Appuyez sur Appuyez longuement sur pour activer le mode de capture en continu. Capture Box prendra 5 photos à la fois. Lecture instantanée - Appuyez pour la lecture du dernier fichier enregistré ou voir la dernière image acquise. - Appuyez pour arrêter la lecture. - Appuyez sur ► pour avancer de 30 secondes. - Appuyez sur ◄ pour reculer de 10 secondes.
Information du disque Appuyez puis appuyez sur OK pour afficher l’information sur le disque. Appuyez de nouveau pour masquer. 4.2 Ajout de commentaires Cette section vous explique comment ajouter des commentaires vocaux à votre enregistrement vidéo.
Si le casque ou le micro sont branchés lors du déroulement avec l'assistant de configuration, le son ne pourra être entendu à partir de votre casque et les instructions sur les commentaires vocaux ne seront pas affiché s. Par conséquent, branchez le casque ou le micro après l'installation complète de l'assistant afin de suivre les instructions pour casque/microphone. Tout commentaire ajouté sera mixé avec le son du déroulement du jeu.
Chapitre 5. Menu OSD Dans le menu, vous pouvez vérifier et gérer vos fichiers et photos sauvegardés et personnaliser vos préférences. 1 Temps restant pour l'enregistrement 3 Connexion réseau 2 Connexion à GameMate 4 Heure actuelle Menu OSD Descriptions Fonctionnement de base - Appuyez sur pour afficher le menu. - Appuyez sur ou pour revenir à l'écran de jeu. - Utilisez les touches ▲/▼ pour faire une sélection dans le menu et OK pour entrer dans un sous-menu.
Appuyez sur F1 pour retirer le périphérique de stockage en toute sécurité. - *Le coin supérieur gauche montre votre périphérique de stockage par défaut actuel et l'enregistrement restant disponible 5.1 Enregistrements et photos (Media Studio) Vous pouvez vérifier les enregistrements et photos prises par Capture Box dans «Enregistrements et photos (Media Studio)» Format d'acquisition: Vidéo MP4 (Codec: Format H.
Lecture vidéo - Appuyez sur ou OK pour débuter la lecture du vidéo sélectionné. - Appuyez sur ou OK pour mettre la lecture à pause. Appuyez sur ou OK pour reprendre la lecture. - Appuyez pour lire la vidéo au ralenti (1/2x). - Appuyez sur pour reculer en 2x, 4x, 8x, 16x, 32x. pour l’avance rapide à 2x, - Appuyez sur 4x, 8x, 16x, 32x. - Appuyez pour lire le fichier à la vitesse normale (1x) lorsque les fonctions de ralenti, rembobinage ou avance rapide sont actives.
5.1.1 Postédition de vidéos enregistrés Cette section démontre comment couper, recombiner et partager des vidéos sur YouTube enregistrés par Capture Box. Menu OSD Descriptions Sélectionnez une vidéo - Sélectionnez le fichier que vous souhaitez modifier à l'aide des touches de navigation ◄/►/▲/▼. É diter/Partager (Edit/ Share) Appuyez sur F3 pour modifier ou partager la vidéo sélectionnée.
Comment modifier (How to Edit) Des directives sur la façon de modifier une vidéo seront affichées; appuyez sur OK pour commencer l'édition. Mode É dit Vous pouvez couper et recombiner votre vidéo sélectionnée en mode É dit. - Pour couper la vidéo, vous aurez besoin de créer un ou plusieurs segments de la vidéo. - É tape 1: - Pour localiser une scène, utilisez les touches de direction ou pour rechercher la scène.
Aperçu - Capture Box recombine automatiquement les segments que vous choisissez de garder pendant le montage. Export - Le temps estimé peut varier selon les disques de stockage. Référez le temps d'exportation à l'utilisation réelle de votre disque de stockage. - Appuyez sur OK pour exporter la vidéo. - Appuyez sur Menu OSD pour continuer l'édition. Descriptions Exportation... (Exporting…) La barre au milieu montre la progression de l'exportation vidéo et le temps estimé.
Quitter (Exit) Appuyez sur OK pour quitter le mode d'édition. - Appuyez sur pour sortir. Appuyez sur F1 pour continuer l'édition. Menu OSD Descriptions Partager des vidéos sur YouTube Utilisez ▲/▼pour sélectionner la tâche que vous souhaitez effectuer. Sélectionnez «Partager sur YouTube (Share on Youtube)» pour partager vos vidéos. Partagez sur YouTube (Share on Youtube) Avant de partager vos vidéos enregistrées sur YouTube, assurez-vous que vous avez: 1.
Assurez-vous que le compte YouTube est vérifié pour télécharger des vidéos qui font plus de 15 minutes. - Appuyez sur pour continuer l'édition. - Appuyez sur OK pour continuer le téléchargement. - Appuyez sur F1 pour passer ce rappel par la suite. Configuration du compte - Utilisez ▲/▼pour sélectionner la tâche que vous souhaitez effectuer. Appuyez sur niveau. pour revenir au dernier Appuyez sur OK pour modifier votre courriel ou mot de passe.
La longueur recommandée de chaque vidéo doit être inférieure à 1 heure. Capture Box est conçu pour l'enregistrement et l'acquisition de matériel média détenus légalement ou autorisés par l'utilisateur seulement. Le téléchargement de vidéos qui sont protégées par droit d'auteur et autres lois n'est pas autorisé. YouTube peut fermer un compte pour des raisons de protection de droit d'auteur. Assurez-vous que votre compte YouTube est vérifié pour télécharger des vidéos qui font plus de 15 minutes.
Interface utilisateur de gestion de fichiers : 1 Liste affichant les fichiers sur le disque dur interne 2 Ensemble d’outils d’édition 3 Liste affichant les fichiers sur le disque USB 4 Zone d’affichage de l’information Description des outils d’édition : Touches numérotées 1 2 3 4 5 Description Copie de fichier sur le disque USB Copie de fichiers sur le disque dur interne Sélectionnez tous Désélectionnez tous Supprimer Français-24
Menu OSD Description Copie de fichier du DD interne vers le disque USB É tape 1: - Sur le côté gauche de la liste, utilisez les touches ▲/▼ pour sélectionner le fichier que vous désirez copier vers le disque USB. Appuyez sur OK pour sélectionner/désélectionner un item. - Sélectionnez puis appuyez sur OK pour sélectionner tous les fichiers. - Sélectionnez puis appuyez sur OK pour désélectionner tous les fichiers.
désélectionner tous les fichiers. É tape 2: - Sélectionnez et appuyez sur OK pour supprimer le fichier de la liste. ou Appuyez sur la télécommande, puis sur OK pour supprimer le fichier de la liste. - Appuyez sur pour annuler la copie de fichiers en cours. É tape 3: - Appuyer sur OK. Enlèvement du dispositif de stockage USB Pour éviter une perte de données, il est hautement recommandé de retirer en toute sécurité votre dispositif de stockage externe.
Chapitre 6. Jumelage de l'appareil avec le GameMate d'AVerMedia GameMate d'AVerMedia est l'application dédiée pour les téléphones intelligents. Elle vous permet d'utiliser votre smartphone comme télécommande. Vous n'êtes qu'à quelques pas de jumeler Capture Box au GameMate. Veuillez d'abord télécharger le GameMate d'AVerMedia à partir de la boutique app. Pour réussir le jumelage, assurez-vous que Capture Box et le GameMate partagent le mê me réseau.
Appuyez pour entrer le nombre prévu d'appariement à quatre chiffres. Vous verrez le GameMate tel qu'il apparaît du côté gauche lorsqu'il s'est correctement jumelé à Capture Box. Vous pouvez également vérifier la connexion du GameMate à partir du Menu. Vous verrez un signe sur le niveau supérieur du Menu. Si la connexion est perdue, veuillez redé marrer l'AP sans fil ou Capture Box et essayez à nouveau.
Inhalt Kapitel 1. 1.1 1.2 1.3 1.4 Die Geräteteile ......................................................................... 2 Frontblende.......................................................................................... 2 Infrarotsensor....................................................................................... 2 LED-Indikator ....................................................................................... 3 Anschlussports ..........................................................
Kapitel 1. Frontblende Das Tastenfeld an der Vorderseite des Gerätes bietet schnellen Zugriff auf häufig verwendete Funktionen. Nr. Tasten Beschreibungen Aufnahme Startet/beendet die Aufnahme 1 Ein/Aus (Power) Schaltet das Gerät ein 2 Zum Erzwingen einer Abschaltung der Capture Box 4 Sekunden gedrückt halten 1.2 Infrarotsensor Wenn Sie die Fernbedienung verwenden, richten Sie diese auf den Infrarot- (IR) Sensor an der Vorderseite des Gerätes.
1.3 LED-Indikator Die LED-Indikatoren an der Vorderseite des Gerätes zeigen den Gerätestatus.
Zustand Quelle Aufnahme Betrieb (Power) Speicherplatz fast erschöpft Leuchtet grün Blinkt langsam Leuchtet grün Blinkt kontinuierlich grün Gerät nicht bereit Probleme wie: Kein Speicher/ kein Signal/ geschützter Inhalt Blinkt kontinuierlich grün Fernbedienungsbefehl wird empfangen Blinkt einmal grün Drücken Sie zum Beziehen des LED-Indikatorstatus [F1]. 1.4 Anschlussports 1.4.
Kapitel 2. Fernbedienung Die nachstehenden Beschreibungen zeigen die Funktionen der Fernbedienungstasten. # 1 2 Tasten Beschreibungen Schaltet das Gerät ein bzw. versetzt es in den Bereitschaftsmodus. Ruft das Hauptmenü auf. Zum Verlassen noch einmal drücken. 3 Drücken Sie zum Bewegen zwischen den Optionen die Navigationstasten. Mit OK bestätigen Sie eine Auswahl. Mit OK fügen Sie dem Segment in der Nachbearbeitung eine Markierung hinzu/entfernen sie. 4 Gibt die zuletzt aufgenommene Datei bzw.
6 Startet die Wiedergabe der ausgewählten Datei. Gibt die Datei bei normaler (1facher) Geschwindigkeit wieder, wenn Zeitlupe, Rücklauf oder Schnellvorlauf aktiv sind. 7 Beendet die Wiedergabe. Beendet die Aufnahme. 8 9 10 11 12 13 14 15 16 Aktiviert den Rücklauf (2fach, 4fach, 8fach, 16fach, 32fach). Ruft die vorherige Seite auf. Blendet den Bildschirm zur Einstellung der Video/Schnappschuss-Qualität ein. Zum Verlassen noch einmal drücken.
Kapitel 3. Einrichtungsassistent Wenn Sie die Capture Box das erste Mal einschalten, erscheint der Einrichtungsassistent. Folgende Schritte führen Sie durch die Erstkonfiguration. Denken Sie daran, zuvor eine Festplatte (intern oder extern) zu installieren und eine Verbindung zum Internet herzustellen. Bei der erstmaligen Initialisierung folgt nach kurzfristiger Anzeige eines schwarzen Bildschirms (circa 20 Sekunden) das AVerMedia-Logo.
Schritt 3 (1) Erinnerung Achten Sie darauf, dass eine NTFS-formatierte Festplatte angeschlossen oder im Gerät installiert ist. (Einzelheiten finden Sie in Kapitel 4.2) Prüfen Sie die Netzwerkverbindung. Drücken Sie zum Starten der Einrichtung OK. Wir empfehlen einen Router, der DHCP-IP-Netzwerke unterstützt. Beachten Sie zur manuellen Verbindungseinrichtung auch Kapitel 6.2.
Schritt 4 (2) Einrichtungsassistenten abschließ en Sobald eine NTFS-formatierte Festplatte verbunden ist, zeigt eine Benachrichtigung an, dass die Einrichtung abgeschlossen ist. Sie können nun direkt mit der Aufnahme und Erstellung von Schnappschüssen beginnen. Drücken Sie OK; dadurch verlassen Sie den Assistenten und können mit der Nutzung der Capture Box beginnen. Der Spielbildschirm erscheint.
Kapitel 4. Grundfunktionen Dieses Kapitel beschreibt Gameplay-Aufnahme, Bilderfassung, das Hinzufügen von Sprachkommentaren zu Videos und die sofortige Dateiwiedergabe. Alle aufgenommenen Dateien oder Schnappschüsse werden automatisch im Standardzielpfad auf der Festplatte gespeichert. Einzelheiten finden Sie in Kapitel 6. 4.1 Aufnahme und Bilderfassung Die Capture Box ermöglicht Ihnen Aufnahme, Bilderfassung und Hinzufügen von Sprachkommentaren zu Videos. Nachstehend folgen die Anweisungen.
Schneller Schnappschuss während des Spielens - Drücken Sie zur Aufnahme des aktuellen Bildes . Drücken Sie zum Aktivieren des kontinuierlichen Bildaufnahmemodus lange . Die Capture Box nimmt 5 Schnappschüsse auf einmal auf. Sofortige Wiedergabe - Drücken Sie zur Wiedergabe der zuletzt aufgenommenen Datei bzw. zur Anzeige des zuletzt aufgenommenen Bildes - Mit . beenden Sie die Wiedergabe. - Drücken Sie zum Vorwärtsspringen um 30 Sekunden ►. - Drücken Sie zum Rückwärtsspringen um 10 Sekunden ◄.
Festplatteninformationen Drücken Sie und dann zur Anzeige der Festplatteninformationen OK. Zum Ausblenden noch einmal drücken. 4.2 Hinzufü gen von Kommentaren Dieser Abschnitt beschreibt, wie Sie Sprachkommentare zu Ihrer Videoaufnahme hinzufügen.
Falls während des Einrichtungsassistenten ein Headset oder Mikrofon angeschlossen wird, kann der Ton nur über Ihren Kopfhörer gehört werden und Anweisungen zum Kommentieren werden nicht angezeigt. Schließ en Sie das Headset oder Mikrofon daher erst nach Abschluss des Einrichtungsassistenten ein, damit Sie den Kopfhörer/Mikrofon-Anweisungen folgen können. Alle hinzugefügten Kommentare werden mit dem Gameplay-Ton vermischt.
Kapitel 5. Bildschirmmenü Im Menü können Sie Ihre aufgenommenen Dateien und Schnappschüsse prüfen und verwalten sowie Ihre Präferenzen anpassen. 1 Restliche Aufnahmezeit 3 Netzwerkverbindung 2 GameMate-Verbindung 4 Aktuelle Uhrzeit Bildschirmmenü Beschreibungen Grundfunktionen - Rufen Sie mit das Menü auf. - Mit kehren Sie zum oder Spielbildschirm zurück. - Treffen Sie mit ▲/▼ Ihre Auswahl im Menü und drücken zum Aufrufen eines Untermenüs OK.
Speichergerätes F1. - *Die Ecke oben links zeigt Ihr aktuelles Standardspeichergerät und die verfügbare restliche Aufnahmezeit 5.1 Aufnahmen/Schnappschü sse (Media Studio) Im „Aufnahmen/Schnappschüsse (Media Studio)“ können Sie mit der Capture Box aufgenommene Videos und Schnappschüsse prüfen. Aufnahmeformat: Video Bild MP4 (Codec: H.264-Format mit AAC-Audio) JPEG Wir empfehlen, nur mit der Capture Box aufgenommene Videos und Schnappschüsse anzusehen. Versuche, mit anderen Geräten (z. B.
Videowiedergabe - Mit oder OK starten Sie die Wiedergabe des ausgewählten Videos. - Drücken Sie zum Unterbrechen der Wiedergabe oder OK. Mit oder OK setzen Sie die Wiedergabe fort. - Drücken Sie zur Wiedergabe des Videos in Zeitlupe (1/2-fach) . - Drücken Sie zum Aktivieren des Rücklaufs bei 2-, 4-, 8-, 16-, 32-facher Geschwindigkeit . - Drücken Sie zum Aktivieren des Schnellvorlaufs bei 2-, 4-, 8-, 16-, 32-facher Geschwindigkeit .
5.1.1 Mit Capture Box aufgenommene Videos im Nachhinein bearbeiten Dieser Abschnitt zeigt, wie Sie mit der Capture Box aufgenommene Videos schneiden, neu kombinieren und auf YouTube teilen. Bildschirmmenü Beschreibungen Ein Video wählen - Wählen Sie mit den Navigationstasten ◄/►/▲/▼ die Datei, die Sie bearbeiten möchten. Bearbeiten / Teilen (Edit/ Share) Drücken Sie zum Bearbeiten oder Teilen des ausgewählten Videos F3.
Anleitung zur Bearbeitung (How to Edit) Anweisungen zur Bearbeitung eines Videos erscheinen; drücken Sie zum Starten der Bearbeitung OK. . Bearbeitungsmodus Sie können Ihr ausgewählten Video im Bearbeitungsmodus schneiden und neu kombinieren. - Zum Schneiden des Videos müssen Sie ein oder mehrere Segmente innerhalb des Videos erstellen. - Schritt 1: - Lokalisieren Sie eine Szene, indem Sie die gewünschte Szene mit den Richtungstasten oder suchen.
Mit F1 wechseln Sie zwischen Szene suchen und Segment-Suche. Drücken Sie zum Löschen aller im Video vorgenommenen Markierungen F2. Mit F3 exportieren Sie das Video. Vorschau - Die Capture Box kombiniert die zum Behalten ausgewählten Segmente während der Bearbeitung automatisch neu. Exportieren (Export) - Die geschätzte Zeit variiert je nach Datenträger. Die Dauer des Exports richtet sich nach dem verwendeten Speichergerät. - Drücken Sie zum Exportieren des Videos OK.
Verlassen (Exit) Drücken Sie zum Verlassen des Bearbeitungsmodus OK. - Drücken Sie zum Verlassen Mit F1 setzen Sie die Bearbeitung fort. Bildschirmmenü Beschreibungen Videos auf YouTube teilen Wählen Sie mit ▲/▼ die Aufgabe, die Sie ausführen möchten. Wählen Sie zum Teilen Ihrer Videos „Auf YouTube teilen (Share on YouTube)“. Auf YouTube teilen (Share on YouTube) Bevor Sie Ihre aufgenommenen Videos auf YouTube teilen, müssen Sie: 1. Ein YouTube-Konto sowie einen persönlichen Kanal erstellen. 2.
- Mit setzen Sie die Bearbeitung fort. - Drücken Sie zum Fortfahren des Upload OK. - Drücken Sie F1, wenn diese Erinnerung anschließ end übersprungen werden soll. Konteneinrichtung - Wählen Sie mit ▲/▼ die Aufgabe, die Sie ausführen möchten. Rufen Sie mit den vorherigen Schritt auf. Drücken Sie zum Bearbeiten von eMail oder Kennwort OK. Mit F1 speichern Sie die von Ihnen vorgenommenen Ä nderungen. - Bearbeitung vor dem Upload - Drücken Sie zum Zurückkehren zur letzten Seite .
Die empfohlene Länge eines einzelnen Videos beträgt weniger als 1 Stunde. Die Capture Box dient der Aufnahme und Erfassung von Medienmaterialien, die rechtlich ausschließ lich dem Nutzer gehören bzw. durch ihn lizenziert sind. Das Hochladen von urheberrechtlich oder durch andere Gesetze geschützten Videos ist nicht erlaubt. YouTube kann das Konto zum Schutz von Urheberrechten einstellen.
Dateiverwaltungsschnittstelle: 1 Eine Liste mit den Dateien auf der internen Festplatte 2 Eine Auswahl an Bearbeitungswerkzeugen 3 Eine Liste mit den Dateien auf dem USB-Datenträger 4 Informationsanzeigebereich Beschreibungen zu den Bearbeitungswerkzeugen: Nr.
1.4.
Bildschirmmenü Beschreibungen Dateien von der internen Festplatte auf den USB-Datenträger kopieren Schritt 1: - Wählen Sie in der Liste auf der linken Seite mit ▲/▼ die Datei, die Sie auf den USB-Datenträger kopieren möchten. Mit OK wählen Sie ein Element aus/ab. - Wählen Sie und drücken zur Auswahl aller Dateien OK. - Wählen Sie und drücken zur Abwahl aller Dateien OK. Schritt 2: - Wählen Sie und drücken zum Kopieren der ausgewählten Datei(en) auf den USB-Datenträger OK.
Dateien lö schen Schritt 1: - Wählen Sie mit ▲/▼ die Datei(en), die Sie löschen möchten. Mit OK wählen Sie ein Element aus/ab. - Wählen Sie und drücken zur Auswahl aller Dateien OK. - Wählen Sie und drücken zur Abwahl aller Dateien OK. Schritt 2: - Wählen Sie und drücken zum Entfernen der Datei aus der Liste OK. oder Drücken Sie an der Fernbedienung und entfernen die Datei anschließ end mit OK aus der Liste. - Drücken Sie zum Abbrechen des Löschvorgangs . Schritt 3: - Drücken Sie OK.
Kapitel 6. Capture Box und GameMate von AVerMedia koppeln GameMate von AVerMedia ist die spezielle App für Smartphones. Sie ermöglicht Ihnen die Nutzung Ihres Smartphones als Fernbedienung. Sie sind nur wenige Schritte von der Kopplung der Capture Box mit GameMate entfernt. Bitte laden Sie zunächst GameMate von AVerMedia aus dem App Store herunter. Stellen Sie zur erfolgreichen Kopplung sicher, dass sich Capture Box und GameMate dasselbe Netzwerk teilen.
Geben Sie den bereitgestellten vierstelligen Kopplungsnummer durch Antippen ein. Bei erfolgreicher Kopplung mit der Capture Box sehen Sie GameMate wie links dargestellt. Sie können die Verbindung von GameMate auch über das Menü (Menu) prüfen. Sie sehen das Zeichen im oberen Bereich des Menüs (Menu). Falls die Verbindung getrennt wird, starten Sie den WLAN -Zugangspunkt oder die Capture Box bitte neu und versuchen es noch einmal.
Indice Capitolo 1. Componenti dell'unità ................................................................... 2 1.1 1.2 1.3 1.4 Pannello anteriore.......................................................................................2 Sensore a infrarossi ....................................................................................2 Indicatore LED ............................................................................................ 3 Porte di collegamento ......................................
Capitolo 1. Componenti dell'unità Il pannello del tasto, situato nella parte anteriore dell'unità, garantisce l'accesso rapido alle funzioni più utilizzate. N. Tasti Descrizioni Registra Premere per avviare/arrestare la registrazione 1 Accensione (Power) Premere per accendere l'unità 2 Tenere premuto il tasto per 4 secondi per forzare lo spegnimento di Capture Box 1.
1.3 Indicatore LED Gli indicatori LED sulla parte anteriore dell'unità mostrano lo stato del dispositivo.
Condizione Spazio di archiviazione scarso Sorgente Registra Accensione (Power) Verde fisso Acceso con una cadenza lenta Verde fisso Lampeggia continuamente in verde Il dispositivo non è pronto Problemi quali mancanza di spazio di archiviazione/nessun segnale/contenuti protetti Lampeggia continuamente in verde Accettazione di un comando del telecomando Lampeggia in verde una volta Premere [F1] per ottenere lo stato dell'indicatore LED. 1.4 Porte di collegamento 1.4.
1.4.
Capitolo 2. Telecomando Le descrizioni di seguito mostrano l'utilizzo dei tasti sul telecomando. . # 1 2 Tasti Descrizioni Premere per accendere/mettere in standby l'unità. Premere per accedere al menu principale. Premere di nuovo per uscire. 3 Premere i tasti di navigazione per spostarsi tra le opzioni. Premere OK per confermare una selezione. Premere OK per selezionare/deselezionare il segmento in fase di post-editing.
6 Premere per avviare la riproduzione del file selezionato. Premere per riprodurre il file a velocità normale (1x) quando sono attivi slow motion, riavvolgimento o avanzamento rapido. 7 Premere per arrestare la riproduzione. Premere per arrestare la registrazione. 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Premere per riavvolgere (2x, 4x, 8x, 16x, 32x). Premere per tornare alla pagina precedente. Premere per visualizzare la schermata di regolazione della qualità video/istantanea.
Capitolo 3. Installazione guidata La prima volta che si accende l'unità Capture Box, viene visualizzata l'installazione guidata. Le seguenti procedure guidano l'utente attraverso la procedura di configurazione iniziale. Assicurarsi di installare un disco rigido (interno o esterno) e di connettersi previamente a Internet. Per la prima inizializzazione, una breve schermata nera (circa 20 secondi) è seguita dal logo AVerMedia.
Fase 3 (1) Promemoria Assicurarsi che un disco rigido con formattazione NTFS sia collegato o installato sul dispositivo (per i dettagli, consultare il Capitolo 4.2). Controllare la connessione di rete. Premere OK per avviare la configurazione. Si consiglia di utilizzare un router che supporti la rete IP DHCP. Inoltre, consultare il Capitolo 6.2 per la configurazione della connessione manuale.
Fase 4 (2) Termine dell'installazione guidata Una volta collegato un disco rigido con formattazione NTFS, viene visualizzato un avviso di impostazioni completate. È possibile avviare la registrazione e scattare immediatamente istantanee. Premere OK per uscire dalla procedura guidata e iniziare ad usare Capture Box. Viene quindi visualizzata la schermata del gioco.
Capitolo 4. Operazioni di base Il presente capitolo guida l'utente alla registrazione del gioco, all'acquisizione di immagini, all'aggiunta di commenti vocali ai video e alla riproduzione immediata di file. I file o gli snapshot registrati vengono salvati automaticamente sulla destinazione predefinita del disco rigido. Per i dettagli, consultare il capitolo 6. 4.1 Registrazione e acquisizione Capture Box consente di registrare, acquisire e aggiungere commenti vocali ai video.
Istantanea rapida durante il gioco - Premere per acquisire l'immagine corrente. Premere a lungo per attivare la modalità di acquisizione continua. Capture Box effettua 5 snapshot per volta. Riproduzione immediata - Premere per riprodurre l'ultimo file registrato o visualizzare l'ultima immagine acquisita. - Premere per arrestare la riproduzione. - Premere ► per saltare in avanti di 30 secondi. - Premere ◄ per saltare all'indietro di 10 secondi.
Informazioni sul disco Premere , quindi premere OK per visualizzare le informazioni sul disco. Premere di nuovo per nasconderle. 4.2 Aggiunta di commenti Questa sezione mostra come aggiungere commenti vocali alla registrazione video.
Se le cuffie o il microfono vengono inseriti durante l'installazione guidata, l'audio può essere ascoltato solo dalle cuffie e le istruzioni sui commenti vocali non vengono visualizzate. Quindi, collegare cuffie o microfono al termine dell'installazione guidata, in modo da osservare le istruzioni per cuffie/microfono. Tutti i commenti aggiunti verranno mixato con l'audio del gioco. Inoltre, finché le cuffie sono collegate al dispositivo, verranno registrati tutti i commenti e l'audio di sottofondo.
Capitolo 5. Menu OSD Nel menu, è possibile selezionare e gestire i file e gli snapshot registrati, nonché personalizzare le preferenze. 1 Tempo restante per la registrazione 3 Connessione di rete 2 Connessione a GameMate 4 Ora attuale Menu OSD Descrizioni Operazioni di base - Premere per visualizzare il menu. - Premere o per tornare alla schermata del gioco. - Usare ▲/▼ per effettuare la selezione sul menu e OK per accedere ad un sottomenu.
Premere F1 per rimuovere in modo sicuro il dispositivo di archiviazione. - *Nell'angolo superiore sinistro viene visualizzato il dispositivo di archiviazione predefinito e il tempo restante per la registrazione disponibile 5.1 Registrazioni e snapshot (Media Studio) È possibile selezionare registrazioni e snapshot acquisiti da Capture Box in “Registrazioni e snapshot (Media Studio)”. Formato di acquisizione: Video Immagine MP4 (Codec: formato H.
Riproduzione video - Premere o OK per avviare la riproduzione del video selezionato. - Premere o OK per mettere in pausa la riproduzione. Premere o OK per riprendere la riproduzione. - Premere per riprodurre il video al rallentatore (1/2x). - Premere - Premere per riavvolgere a 2x, 4x, 8x, 16x, 32x. per andare avanti rapidamente a 2x, 4x, 8x, 16x, 32x. - Premere per riprodurre il file a velocità normale (1x) quando è attiva la funzione rallentatore, indietro veloce o avanti veloce.
5.1.1 Post-editing di video registrati con Capture Box Questa sezione mostra come tagliare, ricombinare e condividere video su YouTube registrati da Capture Box. Menu OSD Descrizioni Selezione di un video - Selezionare il file da modificare tramite i tasti di spostamento ◄/►/▲/▼. Modifica/ Condividi (Edit/ Share) Premere F3 per modificare o condividere il video selezionato. Nome file cambiato Immettere il nome file con i tasti di spostamento ▲/▼ per selezionare caratteri, numeri o simboli.
Come modificare (How to Edit) Quando vengono visualizzate istruzioni su come modificare un video, premere OK per avviare la modifica. Modalità di modifica In Modalità di modifica è possibile tagliare e ricombinare il video selezionato. - Per tagliare il video, è necessario creare uno o più segmenti all'interno del video. - Fase 1: - Per individuare una scena, usare i tasti di direzione o per cercare la scena.
Anteprima - Capture Box ricombina automaticamente i segmenti scelti per mantenerli durante l'editing. Esporta (Export) - Il tempo stimato varia in base ai diversi dischi di archiviazione. Per il tempo di esportazione, fare riferimento all'uso effettivo del disco di archiviazione. - Premere OK per esportare il video. - Premere Menu OSD per continuare l'editing. Descrizioni Esportazione... (Exporting…) La barra centrale mostra lo stato dell'esportazione video e il tempo stimato.
Esci (Exit) Premere OK per uscire dalla modalità di editing. - Premere per uscire. Premere F1 per continuare l'editing. Menu OSD Descrizioni Condivisione di video su YouTube Usare ▲/▼ per selezionare l'operazione da eseguire. Selezionare ‘Condividi su YouTube (Share on YouTube)’ per condividere i video. Condividi su YouTube (Share on Youtube) Prima di condividere i video registrati su YouTube, assicurarsi di: 1. Creare un account YouTube e un canale personale. 2.
- Premere per continuare l'editing. - Premere OK per continuare l'upload. - Premere F1 per saltare in seguito questo promemoria. Configurazione dell'account - Usare ▲/▼ per selezionare l'operazione da eseguire. Premere per tornare all'ultimo livello. Premere OK per modificare e-mail o password. Premere F1 per salvare le modifiche apportate. - Editing prima dell'upload - Premere per tornare all'ultima pagina. - Premere OK per avviare l'upload. - Premere F1 per impostare la privacy.
La durata consigliata di ciascun video deve essere inferiore a 1 ora. Capture Box è destinato alla registrazione e all'acquisizione solo dei materiali multimediali che sono giuridicamente di proprietà o concessi in licenza dall'utente. Non è consentito caricare video protetti da copyright e altre leggi. YouTube potrebbe chiudere l'account per la protezione del copyright. È necessaria la verifica dell'account YouTube quando si caricano video di durata superiore a 15 minuti.
Interfaccia utente di Gestione file: 1 Elenco di visualizzazione dei file presenti nel disco rigido interno 2 Un set di strumenti di editing 3 Elenco di visualizzazione dei file presenti nel disco USB 4 Area di visualizzazione informazioni Descrizione degli strumenti di editing: N.
Menu OSD Descrizioni Copia di file dall'HDD interno al disco USB Fase 1: - Nell'elenco a sinistra, usare ▲/▼ per evidenziare il file da copiare sul disco USB. Premere OK per selezionare/deselezionare una voce. - Selezionare e premere OK per selezionare tutti i file. - Selezionare e premere OK per deselezionare tutti i file. Fase 2: - Selezionare e premere OK per copiare i file selezionati sul disco USB. - Premere per annullare la copia dei file in corso. Fase 3: - Premere OK.
- Selezionare e premere OK per deselezionare tutti i file. Fase 2: - Selezionare e premere OK per rimuovere il file dall'elenco. oppure Premere sul telecomando, quindi premere OK per rimuovere il file dall'elenco. - Premere per annullare l'eliminazione dei file in corso. Fase 3: - Premere OK. Rimozione del dispositivo di archiviazione USB Per evitare la perdita di dati, si consiglia di rimuovere in modo sicuro il dispositivo di archiviazione esterno.
Capitolo 6. Accoppiamento di Capture Box e GameMate by AVerMedia GameMate by AVerMedia è un'app dedicata per smartphone, che consente di utilizzare lo smartphone come telecomando. Con poche procedure è possibile accoppiare Capture Box e GameMate. Prima scaricare GameMate by AVerMedia dall'App Store. Per una accoppiamento corretto, assicurarsi che Capture Box e GameMate siano sulla stessa rete. A tal fine, è necessario un access point wireless per GameMate.
Toccare per immettere correttamente il numero di accoppiamento a quattro cifre fornito. GameMate viene visualizzato come mostrato a sinistro al termine dell'accoppiamento corretto con Capture Box. È inoltre possibile controllare la connessione di GameMate da Menu. Nel livello superiore di Menu, viene visualizzato il simbolo . Se si perde la connessione, riavviare l'AP wireless o Capture Box e riprovare.
Tabla de contenido Capítulo 1. Partes de la unidad ................................................................. 2 1.1 1.2 1.3 1.4 Panel frontal......................................................................................... 2 Sensor de infrarrojos ........................................................................... 2 Indicador LED ...................................................................................... 3 Puertos de conexión ................................................
Capítulo 1. Partes de la unidad Panel frontal El panel de botones que se encuentra en la parte frontal de la unidad proporciona acceso rápido a las funciones que se utilizan con mucha frecuencia. Nº Botones Descripciones Grabar Presione este botón para iniciar y detener la grabación. 1 Alimentació n (Power) Presione este botón para encender la unidad. Mantenga presionado el botón durante 4 segundos para forzar el apagado de su Capture Box. 2 1.
1.3 Indicador LED Los indicadores LED situados en la parte frontal de la unidad muestran el estado del dispositivo.
Condició n Fuente Grabació n Alimentació n (Power) Espacio de almacenamiento escaso Verde permanente Se ilumina a un ritmo lento Verde permanente El dispositivo no está preparado Parpadea en verde continuamente Problemas como falta de almacenamiento, no hay señal o contenido protegido Parpadea en verde continuamente Aceptando un comando del mando a distancia Parpadea en verde una vez Presione [F1] para obtener el estado del indicador luminoso LED. 1.4 Puertos de conexió n 1.4.
1.4.
Capítulo 2. El mando a distancia Las descripciones siguientes muestran el desarrollo de los botones del mando a distancia. Nº Botones Descripciones 1 Presionen este botón para encender la unidad o activar el modo de espera en la misma. 2 Presione este botón para acceder al menú principal. Presiónelo de nuevo para salir. 3 Presione los botones de navegación para moverse por las opciones. Presione OK (Aceptar) para confirmar una selección.
6 Presione este botón para iniciar la reproducción del archivo seleccionado. Presione este botón para reproducir el archivo a velocidad normal (1x) cuando hay movimiento lento, rebobinar o cuando el avance rápido está activo. 7 Presione este botón para detener la reproducción. Presione este botón para detener la grabación. 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Presione este botón para rebobinar (2x, 4x, 8x, 16x y 32x). Presione este botón para volver a la página anterior.
Capítulo 3. Asistente de instalació n La primera vez que encienda la unidad Capture Box, se mostrará el asistente de instalación. Los siguientes pasos le guiarán en el proceso de configuración inicial. Asegúrese de instalar una unidad de disco duro (interna o externa) y conectarla a Internet previamente. La primera vez que inicie la unidad, aparecerá una pantalla con fondo negro (aproximadamente durante 20 segundos) y, a continuación, se mostrará el logotipo de AVerMedia.
Paso 3 (1) Recordatorio Asegúrese de que una unidad de disco duro con formato NTFS está conectada o instalada en el dispositivo. (Para obtener más información, consulte el Capítulo 4.2) Compruebe la conexión de la red. Presione OK (Aceptar) para iniciar la instalación. Se recomienda utilizar un enrutador que admita la red IP de DHCP. Consulte el Capítulo 6.2 para obtener información sobre la configuración de la conexión manual.
Paso 4 (2) Finalizació n del asistente de instalació n Una vez conectada una unidad de disco duro con formato NTFS, se mostrará un aviso de instalación finalizada. Puede empezar a grabar y tomar instantáneas cuando desee. Presione OK (Aceptar) para salir del asistente y empezar a utilizar Capture Box. Se mostrará la pantalla de juegos.
Capítulo 4. Funcionamiento básico En este capítulo se enseña cómo grabar el desarrollo del juego, capturar imágenes, agregar comentarios por voz a vídeos y reproducir archivos instantáneamente. Todos los archivos o instantáneas grabadas se guardarán en el destino de la unidad de disco duro predeterminado automáticamente. Consulte el capítulo 6 para obtener detalles. 4.1 Grabar y capturar Su Capture Box le permite grabar, capturar y agregar comentarios de voz a los vídeos.
Instantánea rápida durante el desarrollo del juego - Presione para capturar la imagen actual. Presione prolongadamente para activar el modo de captura continuo. Su Capture Box tomará 5 instantáneas simultáneamente. Reproducció n instantánea - Presione para reproducir el último archivo grabado o ver la última imagen capturada. - Presione para detener la reproducción. - Presione ► para avanzar 30 segundos directamente. - Presione ◄ para retroceder 10 segundos directamente.
Informació n del disco Presione y, a continuación, OK para mostrar la información del disco. Presiónelo de nuevo para ocultarla. 4.2 Agregar comentarios En esta sección se muestra cómo se agregan comentarios de voz a la grabación de vídeo.
Si enchufa unos auriculares o un micrófono durante el asistente de configuración, solamente se podrá escuchar sonido en los auriculares y no se mostrarán las instrucciones sobre los comentarios de voz. Por tanto, enchufe unos auriculares o un micrófono después de completar el asistente de configuración para seguir las instrucciones de dichos auriculares o micrófono. Todos los comentarios agregados se mezclarán con el sonido del juego.
Capítulo 5. Menú OSD En el menú puede comprobar y administrar los archivos y las instantáneas grabados así como personalizar sus preferencias. 1 Tiempo restante de grabación 3 Conexión de red 2 Conectarse a GameMate 4 Hora actual Menú OSD Descripciones Funcionamiento básico - Presione para abrir el menú. - Presione o para volver a la pantalla de juego. - Utilice los botones ▲/▼ para realizar una selección en el menú y Seleccionar OK para entrar en un submenú.
Presione F1 para quitar de forma segura el dispositivo de almacenamiento. - *En la esquina superior izquierda se muestra el dispositivo de almacenamiento predeterminado actual y el tiempo de grabación restante disponible 5.1 Grabaciones e instantáneas (Media Studio) Puede comprobar tanto las grabaciones como las instantáneas capturadas por su Capture Box en “Grabaciones e instantáneas (Media Studio)”. Formato de captura: Vídeo Imagen MP4 (códec: formato H.
Reproducció n de vídeo - Presione o Seleccionar OK para iniciar el vídeo seleccionado. - Presione o Seleccionar OK para pausar la reproducción. Presione o Seleccionar OK para reanudar la reproducción. - Presione para reproducir el vídeo lentamente (1/2x). - Presione para rebobinar a una velocidad de 2x, 4x, 8x, 16x o 32x. - Presione para avanzar rápidamente a una velocidad de 2x, 4x, 8x, 16x o 32x.
5.1.1 Poseditar vídeos grabados con su Capture Box En esta sección se muestra cómo cortar, recombinar y compartir vídeos en YouTube grabados por su Capture Box. Menú OSD Descripciones Seleccionar un vídeo - Seleccione el archivo que desea editar utilizando los botones de navegación ◄/►/▲/▼. Editar/Compartir (Edit/Share) Presione F3 para editar o compartir el vídeo seleccionado.
Có mo editar (How to Edit) Se mostrará una instrucción sobre cómo editar un vídeo. Presione Seleccionar OK para iniciar la edición. Modo Editar Puede cortar y recombinar el vídeo seleccionado en Modo Editar. - Para cortar el vídeo, necesitará crear uno o varios segmentos dentro del vídeo. - Paso 1: - Para buscar una escena, utilice los botones de dirección o para buscar la escena.
Vista previa - Su Capture Box recombina automáticamente los segmentos que elija conservar durante la edición. Exportar (Export) - El tiempo estimado varía en función de los discos de almacenamiento. Remita el tiempo de exportación al uso real del disco de almacenamiento. - Presione Seleccionar OK para exportar el vídeo. - Pulse Menú OSD para continuar con la edición. Descripciones Exportando...(Exporting...) La barra del medio muestra el progreso de la exportación del vídeo y el tiempo estimado.
Salir (Exit) Presione Seleccionar OK para salir del modo de edición. - Presione para salir. Pulse F1 para continuar con la edición. Menú OSD Descripciones Compartir vídeos en YouTube Utilice ▲/▼ para seleccionar la tarea que desea llevar a cabo. Seleccione ‘Compartir en YouTube (Share on YouTube)’ para compartir sus vídeos. Compartir en YouTube (Share on YouTube) Antes de compartir los vídeos grabados en YouTube, asegúrese de que: 1. Ha creado una cuenta de YouTube así como un canal personal. 2.
- Presione Seleccionar OK para continuar con la carga. - Presione F1 para omitir este recordatorio en lo sucesivo. Configurar la cuenta - Utilice ▲/▼ para seleccionar la tarea que desea llevar a cabo. Presione para volver al último nivel. Presione Seleccionar OK para editar el correo electrónico o la contraseña. Presione F1 para guardar el cambio realizado. - Editar antes de cargar - Presione para volver a la última página. - Presione Seleccionar OK para iniciar la carga.
La longitud recomendada de cada vídeo debe ser inferior a 1 hora. Su Capture Box se ha diseñado para grabar y capturar materiales multimedia cuyos derechos de autor o licencia solamente posee el usuario. No se permite cargar vídeos protegidos por leyes de propiedad intelectual y otras leyes. YouTube puede cerrar la cuenta por motivos de protección de propiedad intelectual. Es necesario realizar la verificación de cuenta de YouTube cuando se carga un vídeo con una duración inferior a 15 minutos.
Interfaz de usuario de la administració n de archivos: 1 Lista que muestra los archivos que se encuentran en la unidad de disco duro interna 2 Conjunto de herramientas de edición 3 Lista que muestra los archivos que se encuentran en el disco USB 4 Á rea de visualización de información Descripciones de las herramientas de edició n: Nº Botones 1 2 3 4 5 Descripciones Copiar archivos al disco USB Copiar archivos al disco duro interno Seleccionar todo No seleccionar nada Eliminar Español-24
Menú OSD Descripciones Copiar archivos desde la unidad de disco duro interna al disco USB Paso 1: - En la lista de la izquierda, utilice los botones ▲/▼ para resaltar el archivo que desea copiar en el disco USB. Presione Seleccionar OK para seleccionar un elemento o anular la selección del mismo. - Seleccione y presione Seleccionar OK para seleccionar todos los archivos. - Seleccione y presione Seleccionar OK para anular la selección de todos los archivos.
Paso 2: - Seleccione y presione Seleccionar OK para quitar el archivo de la lista. o Presione el botón del mando a distancia y, a continuación, presione Seleccionar OK para quitar el archivo de la lista. - Presione para cancelar la eliminación de archivos en curso. Paso 3: - Presione Seleccionar OK. Quitar el dispositivo de almacenamiento USB Para evitar la pérdida de datos, es muy recomendable quitar el dispositivo de almacenamiento externo de forma segura.
Capítulo 6. Asociar su Capture Box y GameMate de AVerMedia GameMate de AVerMedia es la aplicación dedicada para teléfonos inteligentes. Permite utilizar el teléfono inteligente como mando a distancia. Solo necesita unos pocos pasos para asociar su Capture Box a GameMate. En primer lugar, descargue GameMate de AVerMedia de la tienda de aplicaciones. Para que la asociación se realice correctamente, asegúrese de que su Capture Box y GameMate comparten la misma red.
Pulse para introducir el número de asociación de cuatro dígitos proporcionado correctamente. Verá GameMate tal y como se muestra a la izquierda cuando la asociación se realice correctamente con su Capture Box. También puede comprobar la conexión de GameMate desde Menú (Menu). Verá el icono en el nivel superior de Menú (Menu). Si la conexión se pierde, reinicie el PA inalá mbrico o su Capture Box e inté ntelo de nuevo.
Índice Capítulo 1. As Peças da Unidade .............................................................. 2 1.1 1.2 1.3 1.4 Painel frontal ........................................................................................ 2 Sensor Infravermelho .......................................................................... 2 Indicador LED ...................................................................................... 3 Portas de Conexão ..................................................................
1.1 Painel frontal O painel de botão encontrado na frente da unidade fornece acesso rápido às funções comumente utilizadas. N.º de Botões Descrições Gravar Pressione para iniciar / parar a gravação. 1 Energia (Power) Pressione para ligar a unidade 2 Segure o botão durante 4 segundos para forçar o encerramento da Caixa de Captura 1.2 Sensor Infravermelho Quando utilizando o controle remoto, mirar o sensor infravermelho (IR) localizado no painel frontal da unidade.
1.3 Indicador LED Os indicadores LED na frente da unidade exibem o status do dispositivo.
Condição Fonte Gravar Energia (Power) Espaço de armazenamento está baixo Verde sólido Brilha em um ritmo lento Verde sólido Dispositivo não está pronto Pisca em verde continuamente Problemas como o armazenamento de dados/sem sinal/conteúdo protegido Pisca em verde continuamente Aceitando um comando do controle remoto Pisca em verde uma vez Pressione [F1] para obter status de indicador da luz de LED. 1.4 Portas de Conexão 1.4.
1.4.
Capítulo 2. O Controle Remoto As descrições abaixo mostram a distribuição das teclas do controle remoto. # 1 2 Botões Descrições Pressione para ligar a unidade/entrar em modo stand-by. Pressione para acessar o menu principal. Pressione novamente para sair. 3 Pressione as teclas de navegação para se mover entre as opções. Pressione OK para confirmar uma seleção. Pressione OK para marcar/desmarcar segmento em pós-edição.
6 Pressione para começar a reproduzir o arquivo selecionado. Pressione para reproduzir o arquivo em velocidade (1x) normal quando movimento lento, retroceder ou avançar rapidamente está ativo. 7 Pressione para parar a reprodução. Pressione para parar a gravação. 8 9 10 11 12 13 14 15 16 17 Pressione para retroceder (2x, 4x, 8x, 16x, 32x). Para retornar à página anterior. Pressione para exibir a tela de ajuste de qualidade de vídeo/instantâneo. Pressione novamente para sair.
Capítulo 3. assistente de configuração Quando for a primeira vez que você ligar a unidade placa de captura, aparecerá o assistente de configuração. Os passos a seguir irão guiá-lo através do processo de configuração inicial. Certifique-se de instalar um disco rígido (interno ou externo) e para se conectar à internet com antecedência. Para a inicialização pela primeira vez, um curto período de tela preta (aproximad amente 20 segundos) é seguido pelo logotipo da AVerMedia.
Passo 3 (1) Lembre - se Certifique-se de um disco rígido formatado com NTFS está ligado ou instalado no aparelho. (Para mais detalhes, consulte o Capítulo 4.2) Verifique a conexão de rede. Pressione OK para iniciar a instalação. Um roteador que suporta a rede IP DHCP é recomendado. Além disso, consulte Ch. 6.2 para a configuração da conexão Manual. Passo 3 (2) Falha de conexão de rede Se você não tiver conectado a uma rede válida, a uma curta resultado da conexão de rede não serão mostrados.
Passo 4 (2) Finalizando a configuração Uma vez que um disco rígido formatado com NTFS estiver conectado, um aviso Configurações completa será mostrada. Você pode começar a gravar e tirar foto imediatamente. Pressione OK para sair do assistente e começar a usar a placa de captura. A tela do jogo, então aparece.
Capítulo 4. Operações Básicas Este capítulo orienta você para gravar jogos, captura de imagens, adicionar comentário de voz para vídeos e reproduzir instantaneamente os arquivos. Todos os arquivos gravados ou instantâneos serão salvos no disco rígido padrão de destino automaticamente. Consulte o Capítulo 6 para detalhes. 4.1 Gravar e Capturar A Caixa de Captura permite gravar, capturar e adicionar comentário de voz aos vídeos. As instruções são dadas a seguir.
Instantâneo Rápido Durante o Jogo - Pressione Pressione para capturar a imagem atual. para ativar modo de captura contínua. A Caixa de Captura vai tirar 5 instantâneos de uma vez. Reprodução Instantânea - Pressione para reproduzir o último arquivo gravado ou ver a última imagem capturada. - Pressione para parar a reprodução. - Pressione ►para avançar 30 segundos. - Pressione ◄ para retroceder 10 segundos.
Informaçõ es do Disco Pressione e pressione OK para exibir as informações do disco. Pressione novamente para ocultar. 4.2 Adicionando Comentário Esta seção mostra a você como comentário de voz é adicionado à sua gravação de vídeo. Requisitos para fone de ouvido/microfone.
Se o fone de ouvido ou microfone estiver conectado durante o Assistente de Configuraç ão, o som só pode ser ouvido no fone de ouvido e instruções sobre comentário de voz não serão exibidas. Portanto, ligue o fone de ouvido ou microfone depois que você concluir o Assistente de Configuração para seguir as instruções para fone de ouvido/microfone. Todos os comentário adicionados será misturados com o som do jogo.
Capítulo 5. Menu OSD Sob o menu, você pode verificar e gerenciar seus arquivos e capturas instantâneas gravados, e personalizar suas preferências. 1 Tempo Restante para Gravação 3 Conexão de Rede 2 Conectando ao GameMate 4 Hora Atual Menu OSD Descriçõ es Operaçõ es Básicas - Pressione para abrir o menu principal. - Pressione ou para voltar à tela de jogo. - Use ▲/▼ para fazer uma seleção no menu e OK para entrar em um submenu. - No submenu, use ▲/▼ para fazer a seleção e OK para confirmar.
Pressione F1 para remover com segurança o dispositivo de armazenamento. - * O canto superior esquerdo mostra o seu dispositivo de armazenamento padrão atual e gravação restante disponível 5.1 Gravaçõ es e Capturas (Media Studio) Você pode verificar gravações e instantâneos capturados pela Caixa de Captura no “Gravações e Capturas (Media Studio)”. Formato de Captura: Vídeo Imagem MP4 (Codec: formato H.
Reprodução de Vídeo - Pressione ou OK para começar a reproduzir o vídeo selecionado. - Pressione ou OK para dar pausa da reprodução. Pressione ou OK para resumir a reprodução. - Pressione para reproduzir o vídeo em câmera lenta (1/2x). - Pressione para retroceder em velocidade de 2x, 4x, 8x, 16x, 32x. - Pressione para avançar rapidamente em velocidade de 2x, 4x, 8x, 16x, 32x.
5.1.1 Pó s- Editar os vídeos gravados na Caixa de Captura Esta seção mostra como cortar, recombinar e compartilhar vídeos no YouTube gravados pela Caixa de Captura Menu OSD Descriçõ es Selecione um Vídeo - Selecione o arquivo que você gostaria de editar, utilizando as teclas de navegação ◄/►/▲/▼. Editar/Compartilhar (Edit/ Share) Pressione F3 para editar ou compartilhar o arquivo de vídeo.
Como Editar (How to Edit) Uma instrução sobre como editar um vídeo será exibida, pressione OK para iniciar a edição. Modo de Edição Você pode cortar e recombinar seu vídeo selecionado no Modo de Edição. - Para cortar o vídeo, você terá de criar um ou mais segmentos dentro do vídeo. - Etapa 1: - Para localizar uma determinada cena, use as teclas de direção ou para pesquisar a cena.
Visualização - A Caixa de Captura automaticamente reúne os segmentos que você escolher para manter durante a edição. Exportar (Export) - O tempo estimado varia por diferentes discos de armazenamento. Consulte o tempo de exportação para o uso efetivo do seu disco de armazenamento. - Pressione OK para exportar o vídeo. - Pressione Menu OSD para continuar a edição. Descriçõ es Exportando... (Exporting...) A barra no meio mostra a evolução da exportação do vídeo e o tempo estimado.
Sair (Exit) Pressione OK para sair do modo de edição. - Pressione para sair. Pressione F1 para continuar a edição. Menu OSD Descriçõ es Compartilhar vídeos no YouTube Use ▲/▼ para selecionar a tarefa que você gostaria de executar. Selecione 'Compartilhar no YouTube (Share on youtube)' para compartilhar os seus vídeos. Compartilhar no YouTube (Share on Youtube) Antes que você compartilhe os vídeos gravados no YouTube, certifique-se de que você: 1.
- Pressione para continuar a edição. - Pressione OK para continuar carregando. - Pressione F1 para pular este lembrete posteriormente. Configuração de Conta - Use ▲/▼ para selecionar a tarefa que você gostaria de executar. Pressione para voltar ao nível anterior. Pressione OK para editar seu email ou senha. Pressione F1 para salvar as alterações que você fez. - Editar Antes de Carregar - Pressione para retornar à última página. - Pressione OK para começar o carregamento.
O comprimento recomendado para cada vídeo deve ser inferior a 1 hora. A Caixa de Captura é feita para gravação e captura de conteúdo multimídia que são legalmente de propriedade ou licenciados pelo usuário apenas. Carregar vídeos que são protegidos por direitos autorais e outras leis não é permitido. O YouTube pode encerrar a conta para proteção de direitos autorais. A verificação da conta no YouTube é necessária quando você carregar o vídeo que tem mais de 15 minutos.
Interface do Usuário de Gerenciamento de Arquivo: 1 Uma lista exibindo os arquivos localizados no disco rígido interno 2 Um conjunto de ferramentas de edição 3 Uma lista exibindo os arquivos localizados no disco USB 4 Á rea de exibição de informações Descriçõ es das Ferramentas de Edição: N.
Menu OSD Descriçõ es Copiando Arquivos do HDD Interno ao Disco USB Etapa 1: - Na lista do lado esquerdo, use ▲/▼ para destacar o arquivo que você deseja copiar para o disco USB. Pressione OK para selecionar / desselecionar um item. - Selecione e pressione OK para selecionar todos os arquivos. - Selecione e pressione OK para desselecionar todos os arquivos. Etapa 2: - Selecione e pressione OK para copiar arquivo(s) selecionado ao disco USB. - Pressione para cancelar a cópia de arquivos em progresso.
Etapa 2: - Selecione e pressione OK para remover o arquivo da lista. ou Pressione no controle remoto e então pressione OK para remover o arquivo da lista. - Pressione para cancelar a exclusão dos arquivos em progresso. Etapa 3: - Pressione OK. Remoção do Dispositivo de Armazenamento USB Para evitar perda de dados, é altamente recomendável remover com segurança seu dispositivo de armazenamento externo. Siga as etapas abaixo: Etapa 1: Pressione no controle remoto. Etapa 2: Pressione F2 para removê-lo.
Capítulo 6. Emparelhamento da Caixa de Captura e GameMate by AVerMedia GameMate by AVerMedia é o aplicatico dedicado a smart phones. Ele permite que você use seu smart phone como controle remoto. Você está apenas a alguns passos do emparelhamento da Caixa de Captura com GameMate. Faça o download do GameMate by AVerMedia no app store primeiro. Para emparelhar com sucesso, certifique-se de que a Caixa de Captura e o GameMate compartilham a mesma rede.
Toque para inserir o número de emparelhamento de quatro dígitos corretamente. Você vai ver o GameMate como mostrado ao lado esquerdo quando emparelhado com sucesso até com a Caixa de Captura. Você também pode verificar a conexão do GameMate no Menu. Você vai ver o sinal no nível superior do Menu. Se a conexão for perdida, por favor reinicie o AP sem fio ou a Caixa de Captura e tente novamente.