PROSECUTOR 2000 (4 inch LCD) TRUNK MOUNTED UNIT Operation Manual
Please Read CAUTION! RISK OF ELECTRICAL SHOCK! DO NOT OPEN! CAUTION! TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGE IS PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONAL ONLY. CAUTIONS: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Table of Contents FOREWORD.......................................................................4 FEATURE & SPECIFICATION........................ .................... 5 INSTRUCTION IN BRIEF.................................................... 8 INSTALLATION.................................................................. 11 CONNECTIONS.................................................................. 14 BASIC OPERATIONS......................................................... 15 PROGRAMMING................
Foreword We thank you for your purchase of the PROSECUTOR 2000 SYSTEM (Trunk Mounted Unit). You have purchased a high quality system that will provide you with many years of trouble free service. Should you have any question about the system, or any problems, please call (800)- 482-9211 or fax (281)-443-9079.
Features & Specifications CONTROL HEAD CAMERA WIRELESS MICROPHONE VIDEO RECORDER VAULT WIRING HARNESS OPERATION MANUAL Features System Features • • • • • • • • • • • • • Smallest Trunk VAULT Available 16 X optical Zoom Low Light Auto Focus Camera, 1.0 Lux, 8X Digital Zoom Easy to use over head controls Programmable Industrial Grade VCR with proprietary RS-232 Controller Environmentally Controlled VCR .
Features & Specifications Camera • • • • • • • • • • • • Model AVE-8002 Hi-Resolution More than 450 TV Lines – Solid State Optics Lens - X16 Zoom (f=3.9-63mm) Min. Illuminance 1.0 Lux White Balance Auto/Preset/Manual Digital Zoom X8 Operating Temp. 0 deg.C - 40 deg. C Power 12V(2V / 4W Dimension 2.65”W X 2.56”H X 4.4”D Regulation FCC – Class A Focus Auto/Near/Manual/Wide Back Light Compensation Control Head • • • • • • 4 inch color TFT LCD monitor. Durable membrane switch with backlight.
Features & Specifications VCR • • • • • • • • • • • • Industrial grade VHS format Mobile recorder Operating Voltage 8.5V to 15V DC / 15W Operating Temp 0 to 40 (C (32 to 108 (F) Recording Method Dual-head Recording time 8 hour (with T-160 tape) FFW/REW Time < 5 minutes using T-120 tape.
Instructions in Brief Control Head 1 9 6 10 13 14 2 3 4 78 11 12 15 5 16 17 22 21 23 20 19 24 18 5. ZOOM IN 1. AUDIO ON Press this button to Zoom In the image of the front camera. The Audio Light will be ON when the wire less microphone is turned ON. 6. ZOOM OUT 2. LOW TAPE Press this button to Zoom Out the image of the front camera. The Low Tape Light is the warning that the tape is about to END. 7. NEAR FOCUS 3. OUT TAPE Press this button to focus the objects.
10. REWIND Press this button to Rewind the tape while the VCR is in the stop mode or Press in Play mode to do a reverse picture search. 22. INTERFACE connector for interfacing with siren and white light bar. 23. LED This LED will turn ON when the VCR receives the Record and Audio signal from the control head. This will help the officer determine the control head record status from outside the vehicle. 11. PLAY Press this button to start the play back mode. 12. F.F.
IR Remote Control PAUSE/STILL POWER Press during recording to pause recording. Press during the playback to freeze the picture. REC PAUSE/ STILL Caution: If this button is held for 6 seconds then it will master reset the VCR and clear all the programming to factory default. STOP SP/EP SP/EP Don’t use this button. Recording speed can only be set in the on screen programming mode. PLAY REW F.F STOP TRACKING Press this button to stop a running tape.
Installation To properly install the Prosecutor 2000 System, please read and perform each of the following steps in order. Preparation Disconnect the car battery cables. Remove the lower half of the rear seat. Remove the kick panel and trim strips on front and rear passenger side of the car. Remove or loosen the lower half of the trim on the door post between the front and the rear door enough to get cables under. Camera Mount Remove the mount foot from the camera mount.
Trunk Mounting Cont. Connect the Control Console cable , rear Camera and Mic cable, Antenna cable and the Power cable to the rear of the vault. Bundle the cables to create a service loop so that the vault can easily be unlocked, removed from the base plate and cables disconnected. Attaching the cables to the rear of the vault. Control Console Remove the control head mounting plate from the control console (4 screws on front). Remove the sun visors inner attachments (closest to the rear view mirror).
Power Cable This is the gray cable with red and black wires on one end and a 4 pin connector on the other end. Verify the 4-pin connector is connected to the vault in the trunk. Route the cable through the rear seat panel, under the back seat and carpet, to the battery area of the car (routing through the firewall to the battery is preferred). Secure the red wire to +12 V (through the firewall to the battery is the best way). Connect the black wire to chassis ground.
Connections BLUE SIREN (+) INTERFACE CABLE BLACK SIREN (-) WHITE LIGHTBAR +12 V ORANGE IGNITION +12 V CONTROL HEAD (TO LED) FRONT CAMERA CONTROL CABLE RADAR GUN CABLE REAR MIC RADAR GUN IN TRUNK UNIT RED BLACK (TO ANTENNA) 14
Basic Operations POWER UP THE SYSTEM Complete the installation of the “In Trunk system” as describe in the previous section. Turn On the volume/monitor control switch. If the light on the Power does not turn on, check all the system connections. If Light on the POWER is on then you can turn on the system using one of the following methods: 1. From Control Head: Press the “POWER” button on the control head and it will turn “ON” the system 2.
Programming TIME & DATE SETUP In this section we discuss some of the powerful programming features of the “in trunk system”. The programming mode can only be accessed by using the IR remote control. The following table shows some of the IR- Remote button functions used in the programming mode. An Internal clock generates the time and date that is super imposed on the LCD display. After the clock is set, the date and time modes are displayed on the monitor screen (live picture).
Selecting Date Format TITLER 1 You can program up to a 20 character title on the screen. Follow the following steps to program the title on the screen. The default title is ”PROSECUTOR 2000”. 2 3 4 Under the “Time & Date” menu place the cursor in front of “Date Format” and press the “ F.F” button. The cursor will start blinking. Chose the format from the selection yy/mm/dd or mm/dd/yy or dd/mm/yy by pressing either the “+” or “-” button. Exit of all the menus to activate your selection.
MESSAGES The trunk system has two message inputs, each message can display up to 10 characters. These messages are activated on the LCD display when the “in trunk system” gets a signal from the interface cable (if siren or lights are on). See the Installation section for the connections (pin-outs) of the interface cable. By default the “SRN” message appears on the screen when the siren is on. Similarly, the “LTS” message appears on the screen when the lights are turned on.
The default for these 3 settings (Recycle Record, Record over and Power-up Record) is “OFF”. To change any or all settings to “ON”, place the arrow beside the item, press the “F.F.” button, and the arrow will start blinking. Press the “–” or “+” button to switch between ON or OFF. Make your choice and press “F.F.” to save the selection and return to the sub menu.
Horizontal Position 1 Horizontal position sets the alphanumeric text position horizontally. Follow the steps below to set the Horizontal position. 1 2 3 4 5 6 2 3 4 Under the display setting menu place your cursor in front of “Horizontal Position”. Press the “F.F.” button to select the horizontal position. A small box will pop up on the screen. Press the “+” or “-” button to select the appropriate position. After selecting the position press the “F.
Input Voltage Rader Gun Interface The VCR can display the input voltage on the screen. You can turn off or on the voltage message from the display settings. A “LOW VOLTAGE” message will start flashing on the screen if the input voltage is less than 9V. If the voltage is less than 9 V and the cassette is out then a “CASS OUT” message will start flashing on the screen. The VCR will not accept a tape if the input voltage is less than 9V. Follow the steps below to turn the voltage display on or off.
GENERIC This accepts any RS-232 data and displays it on the monitor. This can be from a computer, a BAC, or other device with RS-232 communications. DECATUR HUNTER, DECATUR GENESYS, GOLDEN EAGLE, LTI 20.
Warranty Information The PROSECUTOR 2000 system is covered by a ONE YEAR Warranty for all parts and labor. To obtain service, order parts, or accessories simply call Prosecutor of Texas between 8am5pm Central Standard Time at (800)-482-9211. Should you need any service for your system, you will be given an RMA # with shipping instructions. You MUST have an RMA # on your package before we can accept it. We do repair work on an individual basis.
Protex, Inc. 1617 E. Richey Road. Houston, Texas.