User's Manual

ManualsBrandsAvantronics ManualsElectronicsBluetooth Stereo Audio Transceiver

1. Product Description

Avantree BTTC-200X is a 2-in-1 Bluetooth stereo audio transceiver, which can

easily switch between receive and transmit modes. With standard 3.5mm audio

jack, it's plug & play, no software installation required. And it is very simple to use

and allows your audio devices to send or receive stereo audio via Bluetooth

wireless.

2. Product Overview

(1) LED Indicator

(2) Multi-Function Button (MFB)

(Power on / Off / Pairing)

(3) Micro USB charging socket

(4) 3.5 mm audio jack

(5) TX/RX switch button

What’s in the box:

Avantree BTTC-200X

3.5mm to 3.5mm audio cable

USB charging cable

User Manual

Warranty card

3. Charging

BTTC-200X comes with a built in rechargeable battery that provides a very long

standby time and working time. We recommend charging the battery fully before

using it for the first time.

1) Insert one Micro USB charging cable end to Saturn Micro USB socket, and

put the other end into a standard USB power outlet, such as laptop or

desktop.

2) It takes 3 hours to charge full and reaches its full capacity for the first time.

Each subsequent charge cycle take around 2 hours.

3) LED will indicate red when charging, and goes off when charging is

complete.

4) If you have not used the device for a few months, LED might not turn red

when first charging. It might take 15-35 minutes before the LED turns red.

5) We suggest to fully charge the device at least every two months

Notice:

When battery power is low, the indicator light will flash red. Please recharge

the battery.

4. Transmitter, Turn On / Off

Please push the click button to TX mode from TX / RX positon, before power on.

TX or RX mode can not be changed after powering on Saturn.

Turn On: press and hold the MFB button for about 5 seconds until the blue LED

is on for 1 second

Notice: For the first time use or first time turn on after clear connection list, transmitter

Saturn will automatically enter into pairing mode, the LED light flashes blue quickly.

Turn Off: press and hold the MFB button for about 3 seconds until the red LED is

on for 1 second, and then go off.

Summary of content (4 pages)

PAGE 1
. Product Description Avantree BTTC-200X is a 2-in-1 Bluetooth stereo audio transceiver, which can easily switch between receive and transmit modes. With standard 3.5mm audio jack, it's plug & play, no software installation required. And it is very simple to use and allows your audio devices to send or receive stereo audio via Bluetooth wireless. (1) LED Indicator (2) Multi-Function Button (MFB) (Power on / Off / Pairing) (3) Micro USB charging socket (4) 3.5 mm audio jack (5) TX/RX switch button 2.
PAGE 2
5. Transmitter, Pairing with a Bluetooth device (Tutorial online) After BTTC-200X, under TX mode, has connected to a bluetooth stereo device, you can enjoy music wirelessly. Before pairing, please make sure your Bluetooth stereo device supports Bluetooth A2DP profile. ( such as Bluetooth stereo headset Avantree Jogger, Bluetooth speaker Avantree Pacifica.) Pairing procedure: A．Plug the 3.5 mm audio cable into BTTC-200X’S 3.
PAGE 3
H. After successful connection, the LED light will flash blue twice every 4 seconds. Note: 1. The pairing mode will last 2 minutes. The receiver will enter standby mode if no devices can be connected with 2 minutes. 2. The receiver BTTC-200X can pair with stereo Bluetooth devices with PIN code “0000”, “1111”, “8888” or “1234”. 3. Once power on, the receiver BTTC-200X will be automatically connected with the last connected device. 4.
PAGE 4
10. Declaration of Conformity may cause undesired operation. 10.1. EU This product is CE certified according to the provision of the R&TTE Directive (99/5/EC). Declare that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .