User's Manual
Avantree
Priva II
USB port of TV
Wall charger
USB port of computer
Micro USB charging cable
1 2
Hold for 1 second
until LED flashes
blue and red.
Press and hold the
MFB button for 5s,
then you will see
the BLUE LED is
on for 2s.
Enter pairing mode Reset
Catalogue
1. Features & AptX Low Latency
2. What’s in the box?
3. Product Overview
4. Power ON / Power OFF
5. Pair and connect to 1st Bluetooth headphone/receiver
6. Pair and connect to 2nd Bluetooth headphone/receiver
7. Reconnection
8. Connect Priva III to an audio source
9. Use for PC / Laptop
10. Locating Priva III
11. Restore Factory Default Settings
12. LED indications
13. Product Specifications
1. Features & AptX Low Latency
Avantree Priva III is a Bluetooth audio transmitter incorporating the latest “aptX Low
Latency” technology, for CD-like quality sound with virtually no delay. With
multipoint receiver support, Priva III allows you to share the fun and enjoyment of
audio with others.
Note: Priva III supports true stereo headsets rather than mono A2DP headsets.
Note: Audio delay for Fast stream codec is almost the same as aptX Low
Latency codec, "but the audio quality of the latter is much higher."
Dual link codec
Under Dual Link Mode (connecting with 2 headphones / receivers simultaneously),
the transmission codec will be the one with longer latency, eg: If one device
supports aptX LL and the other only supports aptX, then the final transmission
codec will be aptX; If both headphones supports aptX LL, the final transmission
codec will be aptX LL.
2. What's in the box:
A. Avantree Priva III
B. Magnetic base
C. 3.5 mm audio cable
D. RCA audio cable
E. Micro USB charging cable
F. User manual
G. Quick start guide
3. Product Overview 4. Power ON / Power OFF
Power ON:
Step 1
Power Priva III (no battery attached) via the supplied micro USB cable
to your own USB chargers (wall charger / travel charger, etc.) with
5V/500mA~2A, or PC/TV USB port.
Step 2
Slide the button to “ON”.
Power OFF:
Slide the button to “OFF” or unplug the charging cable.
5. Pair and connect to 1
st
Bluetooth headphones/receiver
The first time you turn on Priva III, it will automatically go into pairing mode - the
LED flashes BLUE and RED alternately.
Step 1
Set your headphones / receiver to pairing mode.
Step 2
Keep the devices close and wait until the LEDs on both devices slow
down. Now Priva III is ready for use.
6. Pair and connect to 2
nd
Bluetooth headphones/receiver
Step 1
Connect your first device as above.
Step 2
Set second headphones / receiver to pairing mode.
Step 3
Set Priva III to pairing mode again – press and hold MFB for 1 second
until the LED flashes BLUE and RED alternately.
Step 4
Keep the devices close and wait until the LEDs on both devices slow
down.
7. Reconnection
There is no need to pair Priva III each use. It will auto reconnect to the last paired
headphones / receiver once you power on both devices and wait for 5~10s.
For other paired headphones / receivers, they may auto reconnect to Priva III after
waiting 5~10s once powered on. Otherwise, please put both devices into pairing
mode.
How to get Priva III into pairing mode manually-
Under standby mode (except dual link mode), press and hold MFB for 1 second
until the LED flashes BLUE and RED alternately.
8. Connect Priva III to an audio source
Priva III supports ANALOG audio output (3.5mm / RCA audio jack or via Digital to
Analog Audio Converter). Please connect Priva III to correct audio output on your TV
or any other device.
How to verify the correct audio output: Simply plug in wired earphones to test the
sound. If they can work with the socket, you can connect Priva III to it.
Optimal
Avoid
Front Back
9. Use for PC / Laptop
Priva III also supports Micro USB audio input, and the sound quality is much
greater than the ANALOG audio input. You can use it in this way on PC / Laptop
(but most TVs will not support this)
10. Locating Priva III
To achieve greater operational range, please don’t hang Priva III behind TV.
11. Restore Factory Default Settings
You may need to reset Priva III if it is not working as expected, such as not pairing,
wrong LED indication, audio issues, etc. When Priva III is reset to factory default
settings, all the paired device information will be erased.
Step 1
Get Priva III into pairing mode – press and hold MFB for 1 second until
the LED flashes BLUE and RED alternately.
Step 2
Press and hold the MFB button for 5s, then you will see the BLUE LED
is on for 2s.
Step 3 Then it will enter pairing mode automatically
Dispose of the packaging and
this product in accordance with
the latest provisions.
FCC ID: 2AITF-BTTC-318
Z-PKMN-TC318-BLK-V3
www.avantree.com
support@avantree.com
1
16
15
14
13
11
10
9
8
7
6
4
5
To take advantage of the better performance of the APTX Low Latency Codec,
the receiver must support the same codec. If the receiver only supports the
normal AptX codec, or the SBC one, those codecs will be used instead.
Audio delay when paired with different headphones/receiver-
Headphones/receiver support -
The audio delay will be
aptX Low Latency codec ~ 40ms
aptX codec ~ 70ms
Fast Stream codec ~ 40ms
SBC codec (most standard Bluetooth audio)
~ 220ms
- 5 -
- 3 -
- 7 -
- 8 -
- 9 - - 10 -
- 4 -
- 1 -
- 6 -
- 2 -
Connect 1st headphone
Connect 1st
headphone as above
Connect to TV’s audio
output port
EnjoyConnect 2nd headphone
Press & hold for 1 sec
into pairing mode again,
wait until connected
- 11 - - 12 - - 13 - - 14 -
- 15 - - 16 - - 17 -
12. LED indications 13. Product Specifications
•
Bluetooth version: 4.2
•
Bluetooth profile: A2DP
•
Audio codec: SBC, Fast Stream, AptX, AptX-LL
•
Operating Range: Up to 30 meters
•
Weight: Body approx. 16 g; Base approx. 7 g
•
Size: 48 mm(L) x 48 mm(W) x 15 mm(H)
Declaration of Conformity
This device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this
device may not cause harmful interference, and 2) this device must accept any interference received, including
interference that may cause undesired operation.Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2AITF-BTTC-318
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with
minimum distance between 20cm the radiator your body: Use only the supplied antenna.
E
A
B
C
GD H
www.avantree.com
User Manual
GVZ>2U]2GZKTI_3[RZOVUOTZ(R[KZUUZN:XGTYSOZZKX
Priva
Simply Convenient
F
www.avantree.com
User Manual
Wireless Adapter
6
2
1
!
"# "
$%&&'
5
4
3
FUNCTION
Set Priva III to pairing mode – Hold for 1 seconds until
flashes
BLUE
and
RED
alternately
Reset Priva III – In pairing mode, Hold for 5 seconds until
BLUE
LED is on for 2s
Power on / off Priva III
Analog Audio input
Connect to USB charger for power
Micro USB Audio input
2
5()*"")+,
7
For more detailed information, please refer to included Quick User Guide.
Enjoy
Connect to TV’s audio
output port
Connected
Wait for 5~15 secs,
both LEDs slow down
Pairing
Get headset
into pairing
mode
Turn on, wait
until LED blinks
blue & red
9IGTSKLUX]GXXGTZ_XKMOYZXGZOUT
3.5mm audio jack RCA audio jack Optical output
Status LED indicator
Power on Blue LED on for 1 second
Pairing mode
Connected with SBC codec
Blue LED flashes once every 5 seconds
Connected with Faststream codec Blue LED flashes twice every 5 seconds
Connected with aptX codec White LED flashes once every 5 seconds
Connected with aptX-LL codec White LED flashes twice every 5 seconds
Reconnect
Restored factory default settings Blue LED on for 2 seconds
LEDs blink blue and red alternately
Blue LED flashes once every 2 seconds
ON OFF
Note: ,!&!-!
.,./#)(#0)8.*0(#09
):-(((:)-!99
;!
,<=!!>"#?$
::-(((=!
89!$
Avantree
Priva II
Avantree Priva III
4
3
*!!9!&
!@!:)A:;
-$
>.-:-(((?>@
-?$
More FAQs on support.avantree.com
Video user guide: Search “Avantree Priva III” on Youtube.com
Telephone support refer to http: //www.avantree.com/contact-us
Email support: support@avantree.com
B$%.("C.)+
3"# "
(::)