User's Manual

ManualsBrandsAutostart ManualsElectronicsRS5304

Table on contents…………………………...1

What’s included……………………….……..2

Notice….…….………………………………...2

Install points to remember…………………2

Features……………………………………….2

Options………………………………………..2

Programmable options……………………..2

Electronic Valet Mode………………………2

Transmitter code learning………...……….3

Multi car operation…………………..….…..3

Tach Adjustment………………………..…..3

Manual Tach adjustment……….……………3

Custom Programming Options..….…..……4

Door lock toggle mode……………..………...4

Vaccum mode……………..……………..……5

Tach watch Lockout………………………….5

Idle Mode……………………………………….5

Diesel Engine.…………………….……………5

Module Reset…………..……………….……..5

Harness Description………………..….…….6

AS-1200/1203/1204 Wiring Schematic…….7

AS-1202 Wiring Schematic……………..…...8

AUTOSTART

AUTOSTARTAUTOSTART

AUTOSTART

AS-1200/1202/1203/1204 SH

AS-1200/1202/1203/1204 SHAS-1200/1202/1203/1204 SH

AS-1200/1202/1203/1204 SH

Automatic transmission remote engine

Automatic transmission remote engine Automatic transmission remote engine

Automatic transmission remote engine

starter systems.

starter systems.starter systems.

starter systems.

NOTICE:

DUE TO THE POTENTIAL FOR DAMAGE TO THE VEHICLE, THE MANUFACTURER IS NOT

RESPONSIBLE FOR ANY ELECTRICAL OR MRCHANICAL DAMAGE TO THE VEHICLE OR TO

THE UNIT THAT HAS CAUSED VEHICLE DAMAGE DUE TO IMPROPER INSTALLATION OF THE

PRODUCT.

THIS UNIT MUST BE INSTALLED BY AN AUTHORIZED AUTOSTART TRAINED TECHNICIAN

USING ALL SAFETY DEVICES SUPPLIED.

Please review the installation guide carefully before any work begins.

WARNING

THIS UNIT IS FOR AUTOMATIC TRANSMISSION ONLY, BEFORE INSTALLING THE UNIT

TEST THAT THE VEHICLE WILL NOT START IF THE GEAR SELECT LEVER IS IN A

DRIVE POSITION. IF IT STARTS IN GEAR, INSTALL A MANUAL TRANSMISSION CAR

STARTER. (AS-1260M)

Rev:1.04 - 8/16/99 Manufactured in Canada by AUTOSTART

INSTALLATION GUIDE

Table of Contents

Summary of content (8 pages)

PAGE 1
AUTOSTART AS-1200/1202/1203/1204 SH Automatic transmission remote engine starter systems. INSTALLATION GUIDE Table of Contents Table on contents…………………………...1 Manual Tach adjustment……….……………3 What’s included……………………….……..2 Custom Programming Options..….…..……4 Notice….…….………………………………...2 Door lock toggle mode……………..………...4 Install points to remember…………………2 Vaccum mode……………..……………..……5 Features……………………………………….2 Tach watch Lockout………………………….5 Options………………………………………..2 Idle Mode……………………………………….
PAGE 2
WHAT’S INCLUDED FEATURES Please review the installation guide before beginning the installation, particularly the wiring diagram and the list of programming options. Prior to installation please be sure that all hardware components required to install the system are in the box.
PAGE 3
procedures should be done every time a new unit is installed. This is because the tach signal from some ignition systems can sometimes be too high or too low, thus causing failed starts under different temperatures. To get the system OUT of VALET mode you must do the following: 1- Turn ignition key to the “ON” position (Wait 3 sec) 2- With key ON, turn Valet switch from the ON position to the “OFF” position. (Wait 3 sec) 3- Now L.E.D should be off.
PAGE 4
vehicle’s starter wire is then interrupted until the starter kill is disarmed by pressing button 1 (unlock) on the remote. If the doors were not locked within the initial 45 seconds of the ignition being turned “OFF” the first press of button 1 will disarm the starter kill, unlocking the already unlocked doors before they can be locked again, arming the starter kill.
PAGE 5
FUNCTION 2 OPTION 1 OPTION 2* OPTION 3 If module is still in Tach Watch Lockout move tach wire to a better tach source and perform an Automatic Tach Setting. Then repeat steps 1 to 5. 2 start attempts 3 start attempts 4 start attempts IDLE MODE FUNCTION 3 OPTION 1 OPTION 2* OPTION 3 FUNCTION 4 6-second crank time 8 second crank time 12-second crank time OPTION 1 gasoline engines & enable idle mode gasoline engines diesel engines & enable idle mode.
PAGE 6
HARNESS DESCRIPTION 7-PIN HARNESS PIN # 1 2 3 4 5 COLOR BLACK VIOLET GRAY EMPTY ORANGE POLARITY Chassis Ground Tach Input (Coil -) Hood Switch Glow plug input(+) Brake switch 6 7 RED YELLOW Valet switch Parking light output DESCRIPTION (connect to...) Ground to vehicles chassis. Connect to vehicle's tach wire (coil -) Hood switch - grounded when hood open Connect to wait to start light on diesel vehicles. To brake switch wire with +12 volt when brake pressed Depends on model. (See wiring Schematic.
PAGE 7
PAGE 8