SRR2-A / BSM Users Manual C PSAD A D F6 User Manual for 24 GHz Blind-Spot Radar Sensor SRR2-A Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.
SRR2-A / BSM Users Manual C PSAD A D F6 AUTHORS Name Organisation Section Frank Gruson Continental, C PSAD A D F6 Frequency Management WW Issue Document Date of Issue Document Owner status maturity (200x-MM-DD) Department (Index) (draft / valid) 1.0 Released 2010-12-16 Frank Gruson 1.1 Released 2011-09-29 Frank Gruson Description C PSAD A D F6 Add FCC labeling requirements C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.
SRR2-A / BSM Users Manual C PSAD A D F6 1 TABLE OF CONTENTS 1 TABLE OF CONTENTS ............................................................................................................................................... 3 2 PURPOSE........................................................................................................................................................................ 4 3 SYSTEM OPERATIONAL DESCRIPTION .................................................................
SRR2-A / BSM Users Manual C PSAD A D F6 2 Purpose In this document an operational description of Continental´s 24 GHz blind spot radar sensor SRR2-A is given. Sufficient information is provided to understand the operation principle, the set up and the tuning of the radar sensor. Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.
SRR2-A / BSM Users Manual C PSAD A D F6 3 System operational description Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.
SRR2-A / BSM Users Manual C PSAD A D F6 (depending on the implementation by the customer) Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.
SRR2-A / BSM Users Manual C PSAD A D F6 4 SRR2-A sensor warning activation zone Figure 1: SRR2-A warning activation zone Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.
SRR2-A / BSM Users Manual C PSAD A D F6 5 SRR2-A sensor component description The SRR2-A sensor consists of the following components: • Plastic housing with sensor CAN connector and sealing • RF antenna board which is plugged into the housing • EMC shield to protect the RF board from digital noise of the ECU board • An aluminum back cover closes the sensor and serves as a mounting area for the sensor to be mounted to the car. Typical mounting angle is 20°C with respect to the driving direction.
SRR2-A / BSM Users Manual C PSAD A D F6 6 SRR2-A sensor software operation Only one operational mode exists which does radar measurements with FM frequency modulation. The sensor operates in this mode during the complete lifetime in the host car. The sensor SW of the test sensors for type approval is configured in such a way that the sensor enters its operational mode once a 12 V battery supply is applied to the supply pin and 0V of the battery is applied to the GND pin.
C PSAD A D F6 SRR2-A / BSM Users Manual 7 SRR2-A radiation hazard This BSM (blind spot monitoring) device emits intentional electromagnetic radiation in the 24,05 to 24.25 GHz frequency range. At a distance of 20cm from the sensor, the radiated power is 0.0027mW/cm 2 Data from “Test report 206-11R1” of COMPLIANCE WORLDWIDE, INC, section 6, page 18 2 This value is a factor of 370 below the legal human exposure protection limit of 1 mW/ cm (MPE) in Europe and US.
C PSAD A D F6 SRR2-A / BSM Users Manual 8 SRR2-A equipment authorization This BSM devices complies with part 15 of the FCC rules (15.249), with RSS-310 of Industry Canada, and with EN 302 858 of ETSI/CEPT on a Class1 basis. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 3. This device may only work when the vehicle is in operation.
SRR2-A / BSM Users Manual C PSAD A D F6 9 SRR2-A labeling (on sensor) USA: FCC-ID: OAYSRR2A (warning statement will be written in user manual, as the sensor is smaller as a hand and the label is not visible to the end user) Canada: Canada 310 (cathegory 2 equipment) China CMIIT ID: 2011DJ2982 Korea + KCC-CEM-C1A-SRR2A Japan: Russia EU: Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.
SRR2-A / BSM Users Manual C PSAD A D F6 10 SRR2-A labeling (in users manual) USA: FCC-ID: OAYSRR2A This device complies with part 15 of the FCC Rules and Industry Canada RSS- 310.
