User Manual

ManualsBrandsAutomotive Data Solutions ManualsElectronicsBLE MOUDLE

ADS-BLEnRF1 MANUAL

 Nordic nRF52832 with ARM Cortex M4F.

 -96 dBm sensitivity

 2 Mbps Bluetooth low energy mode

 1 Mbps, 2 Mbps supported data rates

 TX power -20 to +4 dBm in 4 dB steps

 Single-pin antenna interface

 5.3 mA peak current in TX (0 dBm)

 5.4 mA peak current in RX

 Integrated high performance PCB trace antenna:

 Operation voltage: 1.7V to 3.6V

 Operation temperature: -40°C to +85°Cpin1- Rx (Data from antenna, 0-5 Volts)

pin#

pin name

pin#

pin name

3.3V

P0.08

GND

BLE_TX

P0.31

BLE_RX

P0.30

P0.13

Debug_tx

P0.14

Debug_rx

P0.15

EEPROM-SCK

P0.18

EEPROM-MOSI

P0.19

EEPROM-MISO

RESET

EEPROM-NPSC

BLE_SC

P0.07

BLE_SD

Summary of content (10 pages)

PAGE 1
ADS-BLEnRF1 MANUAL            Nordic nRF52832 with ARM Cortex M4F. -96 dBm sensitivity 2 Mbps Bluetooth low energy mode 1 Mbps, 2 Mbps supported data rates TX power -20 to +4 dBm in 4 dB steps Single-pin antenna interface 5.3 mA peak current in TX (0 dBm) 5.4 mA peak current in RX Integrated high performance PCB trace antenna: Operation voltage: 1.7V to 3.6V Operation temperature: -40°C to +85°Cpin1- Rx (Data from antenna, 0-5 Volts) pin# pin name pin# pin name 1 2 3 4 5 6 7 8 9 10 11 3.
PAGE 2
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. FCC Statement This device complies with part 15 of the FCC Rules.
PAGE 3
Compliance list INTEGRATION INSTRUCTIONS for 996369 D03 OEM the and 996369 D03 OEM by Sections 2.2 through 2.12. Requirement Yes N/A Comment 2.2 List of applicable FCC rules YES List the FCC rules that are applicable to the FCC standards: FCC CFR Title 47 Part 15 modular transmitter. These are the rules that Subpart C Section 15.247 specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies.
PAGE 4
signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host.
PAGE 5
compliance. The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design.
PAGE 6
unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors. 2.8 Label and compliance information Grantees YES are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating “Contains FCC ID” with their finished product.
PAGE 7
for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
PAGE 8
YES 2.12 How to make changes Since . only Grantees are permitted to make permissive changes, it is recommended that module manufactures provide contact information and some guidance to host providers in the integration instructions if they expect their module will be used differently than granted. only Grantees are permitted to make permissive changes.
PAGE 9
IC STATEMENT This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference.
PAGE 10
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.