User's Manual

ManualsBrandsAutomatic Technology ManualsElectronicsWIRELESS WLOCK-02 TRANSCEIVER

Garage Door Lock Installation Instructions

Auto-Lock Kit

Standard Installation

GARAGE DOOR LOCK - ORDER NO. MC-0002

ITEM DESCRIPTION QTY

1 GARAGE DOOR LOCK 1

4 BATTERY C-LR14 2

WIRELESS WBS-1V1 KIT 1 ORDER 14827

5 WIRELESS WBS-1V1 AY 1

6 WBS HARNESS 90MM AY 1

7 WBS HARNESS 400MM AY 1

8 TAPTITE SCREW “P” 2

9 VELCRO 20 X 50 1

MOUNTING SCREW PACK GDL100 ORDER 61411

14 BUTTON HEAD SCREW ZN M6 X 14 2

Limited Sideroom Installation

GARAGE DOOR LOCK - ORDER NO. MC-0002

ITEM DESCRIPTION QTY

1 GARAGE DOOR LOCK 1

2 MOUNTING PLATE 1

3 BRACKET STRIKER GDL100 1

4 BATTERY C-LR14 2

WIRELESS WBS-1V1 KIT 1 ORDER 14827

5 WIRELESS WBS-1V1 AY 1

6 WBS HARNESS 90MM AY 1

7 WBS HARNESS 400MM AY 1

8 TAPTITE SCREW “P” 2

9 VELCRO 20 X 50 1

MOUNTING SCREW PACK GDL100 ORDER 61411

10 BOLT 1/4” - 20TPI - UNCX1/2” SQ NECK 3

11 NUT SER FLNG 1/4” X 20-TP1 UNC ZN 3

12 SCREW TEK 14G-20X25 FLNG HD CL4 4

13 CROSS RECESSED SCREW M6X12 2

It is our strong recommendation that your opener be fitted with SAFETY BEAMS.

Safety Beams detect any obstructions in the door/gate’s path and override automatic operation if one

presents.

This device will slide a bolt into the guide track automatically when the door is closed.

Not suitable for garages that have only one exit.

For emergency release press the emergency unlock button on the lock. This will disengage the lock from

the guide track and allow you to disengage the opener and open the door. The lock will re-engage after

the next complete cycle.

QR Code

To view step by step installation guide video,

download a QR Code Reader App from your

App Store and scan this code.

Doc # 160070_01

Part # 79171

Released 30/06/17

ata

To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s)

used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons

and must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT

EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Summary of content (4 pages)

PAGE 1
Auto-Lock Kit Garage Door Lock Installation Instructions Standard Installation Limited Sideroom Installation GARAGE DOOR LOCK - ORDER NO. MC-0002 ITEM DESCRIPTION GARAGE DOOR LOCK - ORDER NO.
PAGE 2
Auto-Lock Installation Instructions Important Safety Instructions WARNING! • • • DO NOT attempt to disassemble, repair or modify the product. This will invalidate the warranty. Do not allow children to play with the Auto-Lock. Not suitable for garages that have only one exit. CAUTION: Fall from ladder Burns • • • • • Ensure ladder is the correct type for job. Ensure ladder is on flat ground. Ensure user has 3 points of contact while on ladder.
PAGE 3
Auto-Lock Installation Instructions 3 Standard Installation Preparation - mounting on track 1 a. Close the door. b. Using a marker pen, mark the position of the top of the second door wheel from the floor on the track. c. Open the door and transfer this mark to the inside of the track. d. Remove the drilling template label. e. Place the Datum line on the template on top of the line marked inside the track. f. Drill holes in the track using 15/64 in (6mm) and 15/32 in (12mm) drill bits. g.
PAGE 4
Connect Wireless Basestation to Opener AM-808 and AM-888 Preparation of Opener a. Disconnect the power supply to the opener. b. Remove the back cover via screw at top. c. To connect the harness remove the side flap from the side of cover. Slide the WBS harness 3 1/2 inches 6 through the slot in the cover. Connect the harness to the 4 pin connector on the control board as shown on the control board. d. Refit the covers. 6 Mount and connect Transceiver a.