PA700V1 - Overhead Door Operator Instruction Manual (Instruction d’Installation) 700 PA PA7 0 0 FOR RESIDENTIAL USE ONLY Part number #40000 Model: PA700V1 October 2011 www.bnd.com.
WARNING: It is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instructions for future reference. AVERTISSEMENT: pour la sécurité des usagers, il est essentiel de suivre toutes les instructions.
PA700V1 Instruction Manual (Instructions d’installation) CONTENTS PA700V1 Overhead Door Operator Safety Rules Default Settings & Specifications 5 6 About Your Operator 7 Operating Controls Kit Contents 8 10 Installation Single piece C-Rail Assembly 11 Mounting Operator for Track Type Door 12 Mounting Door Bracket & Arms 13 Safety Beam Installation 14 Programming the Operator 15 Via Control Panel
PA700V1 Instruction Manual (Instructions d’installation) CONTENTS PA700V1 Overhead Door Operator How To Use Your Operator Transmitter 22 Removing Battery from Transmitter 23 Manual Door Operation 23 Power Failure 23 Safety Beam 24 Courtesy Light 24 Auxiliary Output 24 Vacation Mode 24 Setting The Pet Mode Position 24 Maintenance 25 Troubleshooting Guide 26 Parameters 27
PA700V1 Instruction Manual (Instructions d’installation) Safety Rules (Les règles de la sécurité) Please read these important safety rules These safety alert symbols indicate a personal safety or property damage instruction exists. Read these instructions carefully. This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules.
PA700V1 Instruction Manual (Instructions d’installation) Default Settings & Specifications Factory default settings Default Step Minimum Maximum Courtesy light time 3 minutes Not adjustable ----- ------ Obstruction force margin 0.7A 0.1A 0 2A Technical specifications Input Voltage 120Vac / 60Hz Input power (max) 150 Watts Standby power, less than 1.
PA700V1 Instruction Manual (Instructions d’installation) About Your Operator Thank you for choosing a PA700 automatic garage door operator. Courtesy Light The technically advanced construction of this operator ensures you enjoy the following benefits: The courtesy light automatically switches on for approximately three (3) minutes when operating the door. This can also be programmed to turn on and off from a transmitter.
PA700V1 Instruction Manual (Instructions d’installation) Operating Controls 01. 02. Terminal Block (J2): V+ (+35V/+24V) is used to power Accessories such as external receiver (200mA max) SB-1 (mandatory) input is used to connect to Safety Beam 0V is a 0 volt connection for Safety Beam SB-2 input is used to connect to Safety Beam 0V is a 0 volt connection for Safety Beam AUX/OSC This output has two chosen functions: AUX allows the operator to operate other devices such as an alarm system.
PA700V1 Instruction Manual (Instructions d’installation) 9 Fig. 01 01 02 03 04 05 06 07 08 09 10 11 12 16 14 15 13 © Copyright 2011 D Power Drive : Instruction Manual Fig.
PA700V1 Instruction Manual (Instructions d’installation) Kit Contents PA700 Kit contains (Fig. 03) Fig. 03 1 x PA700 powerhead drive unit; 1 x Transmitters set (Set includes PTX-5 (hand held remote control) and WTX-4 (wall mounted remote control) transmitters with batteries); 2 x Door attachment arms; 1 x Accessory and hardware pack; 1 x Installation Manual. plus Single Piece C-Rail with Preassembled Chain (Belt) NOTE: Chain in one piece rail has been tensioned by the factory.
PA700V1 Instruction Manual (Instructions d’installation) 11 Installation Shaft Where possible, install the door opener 7 feet or more above the floor. C-Rail Attachment Fig. 05 Step 1 - Attach C-Rail to Powerhead Locate and insert the powerhead’s shaft into the C-Rail’s sprocket as shown in Fig.05. Locate shaft into sprocket Screws M4 X 8 2) t (x cke a r b ck Tra Step 2 - Secure C-Rail to Powerhead Fig.06 Fix the two track brackets as shown in Fig.06.
PA700V1 Instruction Manual (Instructions d’installation) Mounting Operator for Track Type Door Step 3 - Determine Bracket Position a. Level b. Track Fig.7 c. Door Open the door and find the highest point of travel of the top door panel. Using a level, transfer this height to the wall above the door (Fig.7) and mark a line 2.36” (60mm) above it. Determine the centre point on the wall above and on top of the door. Then draw two lines extending 21.5mm from each side of the centre point. (Fig.
PA700V1 Instruction Manual (Instructions d’installation) 13 Mounting Door Bracket and Arms Step 7 - Alternative Mounting Option Drill hole at centre of track (recommended bolt size M6 or M8) The operator can be fastened to the roof by driving a bolt through the C-Rail into a structural timber support. The bolt head’s height must not exceed 6mm (Fig.11). Step 8 - Mounting Door Bracket The door bracket comes in two parts. The bottom plate with two mounting holes is used on its own for one piece doors.
PA700V1 Instruction Manual (Instructions d’installation) Safety Beam Installation IMPORTANT NOTE: The Safety Beam must be installed and connected before the travel limits are set 5 3 4 Step 10 - Safety Beam Fig.14 6 1 2 5 A Safety Beam extends across the door opening. This Safety Beam is designed to detect an obstruction while the door is closing and to send a signal to the door operator to reverse or stop the door movement. Step 10.1 - Fitting the Safety Beam a. b. c. d. Fig.15 Step 10.
PA700V1 Instruction Manual (Instructions d’installation) 15 Programming The Opener Via Control Panel Important note: The OPERATE button will not function until the open and close limit positions are set. Note: The door and shuttle must be engaged into the chain index. The door should be open approximately half way. Fig.17 NOTE: The Safety Beam must be installed before setting the travel limits. Step 11.
PA700V1 Instruction Manual (Instructions d’installation) Testing Safety Obstruction Force CAUTION: Take care when testing the Safety Obstruction Force. Failure to follow this warning can result in serious personal injury and/or property damage. Step 12.1 Test the Close Cycle Press the OPERATE button to open the door (Fig.20). Place an object approximately 1-1/2”(38mm) high (or a 2”x 4” board laid flat) on the floor under center of garage door opening (Fig.21). c.
PA700V1 Instruction Manual (Instructions d’installation) 17 Setting Safety Obstruction Force Adjusting Safety Obstruction Force The safety obstruction force is calculated automatically and normally does not require adjustment. The only time the force may need to be adjusted is due to environmental conditions, such as areas that are windy, dusty or have extreme temperature changes that affect the operability and movement of the door. Fig.
PA700V1 Instruction Manual (Instructions d’installation) Coding Transmitters Step 13.1 - Coding a Transmitter Button for Door Operation (Fig.25) The operator can only operate from transmitters that have been programmed into its receiver. The receiver needs to learn the codes of any transmitter that will be used with the operator. Up to eight (8) codes can be stored in the receiver’s memory. Fig.25 a. Select one of the four buttons b. c. d. Press and release the DOOR CODE button.
PA700V1 Instruction Manual (Instructions d’installation) 19 Coding Transmitters Step 13.3 - Setting the Transmitter to Operate Vacation Mode (Fig.27) The operator can be programmed into a “Vacation Mode” where the opener will not respond to any transmitter except one preprogrammed unit. a. b. c. d. e. Press DOOR CODE button three times. The DOOR CODE LED will illuminate and the courtesy light will flash slowly (once every two seconds) to indicate Vacation learning mode is active.
PA700V1 Instruction Manual (Instructions d’installation) Coding Transmitters Step 13.5 - Setting the Transmitter to Operate Pet (Pedestrian) Mode (Fig.29) The operator can be programmed into a “Pet Mode” where the door opens partially to allow pets to enter/exit the garage: Fig.29 a. b. c. d. Fig.30 Press the DOOR CODE button five times, the DOOR CODE LED will illuminate and the courtesy light will flash quickly (twice per second) to indicate learning mode for Pet Mode is active.
PA700V1 Instruction Manual (Instructions d’installation) 21 Accessories Terminal Block V+ SB-1 J2 A variety of wired accessory items can be connected to the terminal block J2 such as Safety Beam, Electric Key Switch and more (Fig.32). The terminal block J2 also features auxiliary output for controlling other devices from your transmitter. These can include: an alarm system, additional mega code receiver or an automatic gate. Terminal J2 connections from top to down are as follows: 1. V+ (+35V/+24V); 2.
PA700V1 Instruction Manual (Instructions d’installation) How To Use Your Operator For maximum efficiency of your operator, your garage door must be in good operating condition. An annual service of your garage door by a garage door professional is recommended. CAUTION - Activate the operator only when the door is in full view, free of obstructions and with the operator properly adjusted. No one should enter or leave the garage while the door is in motion.
PA700V1 Instruction Manual (Instructions d’installation) 23 How To Use Your Operator Removing the Battery From the Transmitter (Battery Type: 3V Lithium Battery CR2032). Use a non-metallic object (e.g. pen) to remove the battery. (Fig.34) In-built Locking Facility DO NOT lock your door when your operator is engaged as it has in-built locking facility. With the operator engaged your door will be locked whether the power is on or off. Fig.
PA700V1 Instruction Manual (Instructions d’installation) How To Use Your Operator Safety Beam A Safety Beam Kit must be fitted to this operator. • When this Kit is fitted, the operation of this device is such that if an object (i.e. car, child, etc.) blocks the Safety Beam, then the garage door operator will not close the door automatically. • When the Safety Beam is fitted but not operating correctly, then the door once opened automatically, will not close automatically.
PA700V1 Instruction Manual (Instructions d’installation) Maintenance The SERVICE LED will indicate the requirement for a service and/or adjustment. To reset the SERVICE LED when the door is serviced, reprogram the Door Travel Limits and the Door Travel Force – on completion of this programming the SERVICE LED will go out. CAUTION: Frequently examine door, particularly cables, springs and mountings for signs of wear, damage or imbalance.
PA700V1 Instruction Manual (Instructions d’installation) Troubleshooting Guide Symptom Possible cause Remedy The opener does not work from the transmitter Garage door in poor condition e.g. springs may be broken Check the door’s operation - see monthly maintenance (Page 25) The opener does not have power Plug a device e.g.
PA700V1 Instruction Manual (Instructions d’installation) Parameters Door status indicators Door opener state OPEN LED (green) Open On Close Opening CLOSE LED (red) Beeper On Flashing Closing Flashing Door travel stopped Flashing Door obstructed when opening Flashing Door obstructed when closing Flashing Flashing Opener overloaded Alternating flashes Mains power interrupted Rapid flashes Beeps while door is moving Alternating flashes Button Function OPERATE Opens/stops/closes the d
PA700V1 Instruction Manual (Instructions d’installation) Spare parts list
PA700V1 Instruction Manual (Instructions d’installation) © Copyright 2011 D Power Drive : Instruction Manual 29
PA700V1 Instruction Manual (Instructions d’installation) Warranty 1. Definitions ‘Purchaser’ means the purchaser of the Operator. ‘Operator’ means the ‘PA700 Automatic Garage Door Operator’ ‘Authorised Distributor’ means an authorised distributor of the Operator. ‘Major Components’ means all components of the Operator that make up the powerhead that is attached to a garage door. ‘Ancillary Components’ means all components of the Operator which are not Major Components.
PA700V1 Instruction Manual (Instructions d’installation) Warranty Purchased From: Installed By: Installed Date: The Purchaser shall complete this certificate and keep it together with a copy of the receipt of purchase in a safe place – production of such information will assist the handling of a claim made under this warranty.
PA700V1 Instruction Manual (Instructions d’installation) Optional Accessories There is a range of additional accessories for your added convenience and security. • Keyring Transmitter - Ideal for personal use when entry into the house may be via the garage. • Transmitter Wall Button - Allows you to operate the operator within 32.8ft (10 metres) of the door. Ideal for mounting inside the house. • Combo Access Kit - Keyswitch function will open the door without a transmitter.
PA700V1 Instruction Manual (Instructions d’installation) © Copyright 2011 D Power Drive : Instruction Manual 33
©Copyright October 2011. All Rights Reserved. www.