INSTRUCTION MANUAL I j Before You Begin Check to make sure you have the following: A 荨二回 (2) BOLT M6 x 60 mm c 仰一勘 B 仰 D 初一 (2) BOLT M6 x 35 mm E@ (8) WASHER d8.5 x D17 x 1.6 F二 (2) WASHER (1) BACK CUSHION @RIGHT ARM 3)LEFT ARM H '0 (I (4) JAM NUT M8 x 1.25 mm G)BACK ASSEMBLY (4) BOLT M6 x 15 mm (4) BOLT M8 x 30 mm G J [ Part Identity (8) WASHER d6.5 x D13 x 1.0 J 二二了 (1) SEAT CUSHION Tools 勹勹三 i;.................................................................................
I Assembly Instructions STEP 1 PARTS REQU IRED: 1 & 2 I STEP 2 PARTS REQU IRED: 1, 2, A, & H Keep the bolts loose. 1 Attention: Make sure that each bolt needed for all steps matches the corresponding figure to ensure proper assembly. STEP 3 PARTS REQU IRED: 2, 3, 4, B, & H Keep the bolts loose. Note: The labels marked "L" and "R" on the arms should coincide with Figure to ensure proper assembly. STEP 4 PARTS REQU IRED: 1, 3, 4, C, & H Tighten all bolts by using the supplied Hex key.
STEP 5 STEP 6 I J To maintain the beauty of your garden furniture, wipe with a clean, damp cloth before each use.
I I I Part Identity Before You Begin ► Check to make sure you have the following: @A (2) SCREW ST4.2 x 16 mm @c 炉 扣 @)B @)COVER 仰 (4) BOLT M6 x25 mm (4) BOLT M6 x40 mm @E@ @)F (14) WASHER d6.5 xD13 x1.0 (1) LAVA ROCKS @GO(4) BOLT M6 x 10 mm (DREAR FRAME (6) BOLT M6 x 15 mm @)o !Tools I @FRAME B (J)TABLE TOP I ' 勹 ; ........................................ : @UPPER CONNECTOR I WARNING I • Use the correct bolts as indicated.
I Assembly Instructions FIGURE 5 Step 4: Insert the upper connector into the holes of the front door. Fasten the upper connector to the frame B by using bolt (B) and washers (E). Completely tighten all of the nuts and bolts. Close the doors. See Figure 4. Note: Shut the doors lightly. Do not slam the doors to close. � . . . FIGURE 6 I Step 5: Place the table top onto the frame assembly. Fasten them together by using bolts (B) and washers (E).
Certificate of Compliance Certificate: 80039893 Master Contract: 301119 Project: 80162456 Date Issued: 2023-05-22 Issued To: NINGBO KAITONG ELECTRONICS CO.,LTD NO.5 KANGXING ROAD, DAHE INDUSTRIAL PARK, DONGQIAN LAKE, Ningbo, Zhejiang, 315121 China Attention: Leon Zhou The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only.
Certificate: 80039893 Project: 80162456 Master Contract: 301119 Date Issued: 2023-05-22 KT-FPS-S056 KT-FPS-S057 KT-FPS-S058 KT-FPS-S059 KT-FPS-S0510 KT-FPS-S0511 KT-FPS-S0512 KT-FPS-S0513 KT-FPS-S0514 KT-FPS-S0515 KT-FPS-S0516 KT-FPS-S0517 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 KT-FPS-R051 KT-FPS-R052 KT-FPS-R053 KT-FPS-R054 KT-FPS-R055 KT-FPS-R056 KT-FPS-R057 KT-FPS-R058 KT-
Certificate: 80039893 Project: 80162456 KT-FPT-S1460 KT-FPTT-S0116 KT-FPTT-S1442 KT-FPT-RE15T331170 KT-FPT-RE15T331272 KT-FPT-RE15T331272A KT-FPT-RE15T331481 KT-FPT-RE15T331170A KT-FPT-RE15T337548A KT-FPT-RE15T3310048 KT-FPT-RE15T3320010A KT-FPT-RE15T331160A KT-FPT-RE15T331160B KT-FPT-035S044861 KT-FPT-035R146861 KT-FPT-R255R141263 KT-FPT-S255S1215100 Master Contract: 301119 Date Issued: 2023-05-22 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 50,000 35,000 35,000 55
Supplement to Certificate of Compliance Certificate: 80039893 Master Contract: 301119 The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Product Certification History Project Date Description 80162456 2023-05-22 Update report 80039893 to add models KT-FPT-R255R141263, KT-FPTS255S1215100, KT-FPS-S/R series per ANSI Z21.97-2017 / CSA 2.412017. Class no. 2701 03/83.