Quick Guide

ManualsBrandsAUTEL ROBOTICS ManualsElectronicsEVO II Mobile Station

EVO Ⅱ Mobile Station

Quick Guide

Model：MDCMS-2

Disclaimer

To ensure safe and successful operation of yourbase station, please strictly follow the

operating instructions and steps in this manual.

If the user does not abide by the safety operation instructions, DTO Smart will not be

responsible for any product damage or loss during use-whether direct or indirect,

legal, special, accident or economic loss (including but not limited to loss of profit)-

Provide warranty service. Do not use incompatible parts or use any method that does

not comply with the official instructions of Autel Smart to modify the product.

The safety guidelines in this manual will be updated from time to time. To ensure that

you get the latest version, pleasevisit www.auteldrones.com/support/downloads/

battery safety

EVO Ⅱ base preclude the use of lithium polymer batteries. Improper use of lithium

polymer batteries can be dangerous. Please ensure that all the following battery usage,

charging and storage guidelines are strictly followed.

Warning

● Only use the battery and charger provided by DTO Smart. It is prohibited to

modify the battery pack and its charger, or use third-party equipment to replace

it.

● The electrolyte in the battery is extremely corrosive. If the electrolyte accidentally

spills into your eyes or skin, please wash the affected area with clean water

immediately and seek medical attention.

Precautions

1. According to local radio regulations, use base stations with corresponding

frequency bands and comply with local radio laws and regulations.

2. Do not excessively bend and fold the wire during installation.

3. When installing and placing, make sure that the base station is level with the

horizontal plane.

Summary of content (12 pages)

PAGE 1
EVO Ⅱ Mobile Station Quick Guide Model：MDCMS-2 Disclaimer To ensure safe and successful operation of yourbase station, please strictly follow the operating instructions and steps in this manual. If the user does not abide by the safety operation instructions, DTO Smart will not be responsible for any product damage or loss during use-whether direct or indirect, legal, special, accident or economic loss (including but not limited to loss of profit)Provide warranty service.
PAGE 2
4. Use the base station in an open environment free from radio interference. Be sure to turn off other wireless devices in the same frequency band before using it. 5. Please make sure that the antennas of all devices are not blocked during use. 6. Use original accessories or accessories certified by Autel. The use of non-original accessories may cause danger to the safe use of the system. 7. Make sure that no foreign objects (such as water, oil and other liquids, sand, etc.) enter the parts. 8.
PAGE 3
4 component description base station body 2. WiFi indicator 3. RTK indicator 4. Power indicator 5. USB-C charging port 7.
PAGE 4
10. Turntable mounting hole 11.
PAGE 5
1. Fixing screw 2. Knob 3. Telescopic pole 4. Foot nail ready for charging Short press (<1 second) the power button once to check the battery level.
PAGE 6
Red: Electricity>10% Red flashing slowly: Electricity <10% charging methodcharge When using thefor the first time, be sure to fullythe battery. Please use a dedicated charger to charge the base station. 1、 Plug the Type-C power cord into the Type-C port of the base station, and the base station will automatically enter the charging mode (either when it is turned on or off). 2、 When charging, the base station power indicator light flashes, and the battery power is indicated by different colors.
PAGE 7
RTK indicator light Description Green: Number of satellites>16, good signal (normal flight) Yellow: Number of satellites 6-15, poor signal (it is recommended to adjust the base station to an open area) Red Slow flashing: number of satellites <6, poor signal (recommend the base station to be placed in an open area) Light off: no RTK signal (indoors or abnormal base station RTK) use to connect to a ground station or aircraft connection method Take the normal mode as an example, the specific operation is as f
PAGE 8
the "use base station connection" option. EVO Ⅱ GNSS base station is Choose a place with a wide view to set up the EVO Ⅱ GNSS base station and mark it (align the center of the tripod with the center of the mark point) so that the base station can be accurately reset after being moved. 1. Open the tripod, stretch the three telescopic rods to a suitable length, and then tighten the knob to ensure that the tripod is stable. 2. Install the base station body to the tripod and tighten the lock nut on the body.
PAGE 9
which means the aircraft has entered RTK positioning mode. Firmware upgrade(Is there a firmware upgrade?) How to upgrade base station firmware 1. Make sure that the entire UAV system (including aircraft, base station, and ground station) is turned on and connected normally. 2. Run the Autel Voyager App, enter the "Settings" interface, click "Software Update -> UAV Firmware", and complete the upgrade operation of the entire system according to the system prompts.
PAGE 10
Communic data link Wi-Fi ation operating 2.4/5.8GHz; and data frequency storage equivalent isotropic Wi-Fi radiated 2.4 GHz power (EIRP) SRRC/CE/MIC/KCC: <20 dBm; FCC/NCC: <22 dBm 5.8 GHz SRRC/NCC/FCC: <22 dBm CE: <14 dBm Memory capacity No inertial Functional Built-in 6-axis IMU measurem characteristics ent unit electrical Power 7.5 W characteris consumption tics Power supply 5 to 20 VDC Battery type: Lithium polymer battery Capacity: 4950 mAh Energy: 57.
PAGE 11
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 12
Note: The content is subject to update without notice. You can check the latest version on the official website of Autel Intelligent https://www.autelrobotics.