1 Instruction Manual for the use and the maintenance of the Radio Remote Control Original instructions Part B: Conformity and frequencies (433.050-434.
3 THIS PART OF THE MANUAL CONSISTS OF Part B - Information, instructions and warnings for the Conformity and frequencies (433.050-434.790MHz e 915-928MHz). The Manual consists of Part A – General, Part B – Conformity and Frequencies, Part C – Transmitting Unit, Part D – Receiving Unit, Part E – Battery and Battery Charger, plus the Technical Data Sheet.
It is also the responsibility of the Manufacturer and of the design professionals of the Machine on which the Autec Radio Remote Control is to be installed and used to be certain that the structure, condition, organization and markings of the Machine as installed at the facility is appropriate for and will allow for the safe and reliable use and control of the Machine through the Autec Radio Remote Control interface.
5 IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR OFFICERS, MANAGERS AND SUPERVISORS, to be certain that all Users of the Autec Radio Remote Control and that all Persons who are or will be working with or near the Machine operated by or through the Autec Radio Remote Control are fully and properly educated and trained by qualified Personnel in the proper and safe use of the Autec Radio Remote Control and of the Machine, including without limitation complete familiarity with and un
INDEX 1 2 3 4 Information on the use of instructions ...................................................................... 7 1.1 Structure of the Instruction Manual ....................................................................... 7 1.2 Caption and terminology ...................................................................................... 9 1.3 Symbols .............................................................................................................. 9 1.
7 1 Information on the use of instructions Before reading this part of the Manual, you must read and understand the general part (Part A) of the Manual provided with the Radio Remote Control. 1.
Usage and maintenance instructions are supplemented by the Radio Remote Control's Technical Data Sheet, that: - Describes the Transmitting Unit's configuration - Indicates the relation between commands sent by the Transmitting Unit and those available on the Receiving Unit. Usage and maintenance instruction as a whole are to be considered as an integral part both of the Autec Radio Remote Control and of the Machine, system, device or Machinery system where the Radio Remote Control is installed.
1.2 9 Caption and terminology Contact Autec if any of the instructions, symbols, warnings or images are not clear and understandable, or if you have doubts or questions.
1.4 To whom the instructions are addressed Addressees of instructions are listed in the paragraph with the same title in the general part: please refer to that part. 1.5 Instruction storage Regulation for the storage of instructions are described in the paragraph with the same title in the general part: please refer to that part. 1.
11 2 Brief product presentation 2.1 Series, Radio Remote Control and Unit Autec Air series' Radio Remote Controls are designed to be used on Machines and provide a command interface to their command and control system, to be used from an appropriate distance and position. 2.
3 Conformity Addressees of instructions must: - Make sure that the Radio Remote Control works within the frequency band permitted in the country where it is used. - Make sure that the Radio Remote Control works correctly, in compliance with the applicable standards in the relevant country. - Not modify the Radio Remote Control conformity, by performing modifications or technical operations that change its operation.
13 3.3 FCC conformity A Air series' Radio Remote Control working in the 915-928MHz frequency band, whose Units are listed in the following table, complies with the requirements of the standards FCC (Federal Communication Commission) Part 15.
Place the antenna of the Receiving Unit in a position that ensures a minimum separation distance of 20cm from all the people that can be in the working area. Read carefully the section of the Manual where the antenna position is described, both in the general part and in the specific part referring to the Receiving Unit. Autec allows you to use only the dedicated antenna supplied either with the remote control or as original spare part.
15 3.4 IC conformity A Air series' Radio Remote Control working in the 915-928MHz frequency band, whose Units are listed in the following table, complies with the requirements of the standards IC (Industry Canada) RSS-102.
Autec allows you to use only the dedicated antenna supplied either with the remote control or as original spare part. The use of any other type of antenna is prohibited and will invalidate the warranty. As required by the document "RSS-Gen — General Requirements and Information for the Certification of Radio Apparatus", the following indication is valid for all the Units listed in the previous table. This device complies with Industry Canada's licence-exempt RSSs.
17 4 Frequencies Air series' Radio Remote Controls can work in two different frequency bands: 433.050434.790MHz or 915-928MHz. The Radio Remote Controls' working frequency is defined by market-specific laws and standards. In order for the system “Machine+Radio Remote Control” to be compliant and therefore to be used, these laws and standards must be respected: if they are not, the Radio Remote Control cannot and must not be used.
4.2 Frequency band 915-928MHz 4.2.1 Frequencies The radio link between the Units of Autec Air series Radio Remote Controls is established at one of the frequencies permitted by the USA, Canadian and Australian standards in force when the system is put on the market.
AUTEC 19 LIUACF006_eng-00
LIUACF006_eng-00 AUTEC
