User's Manual

ManualsBrandsAutec ManualsElectronicsTransceiver unit

Original instructions

AIR SERIES

Part C: LK6 and LK8 transmitting units

INDEX

1 Description ............................................................................................................ 2

2 Technical data ....................................................................................................... 3

3 Technical data sheet ............................................................................................. 3

4 Plates ..................................................................................................................... 4

4.1 Plates on LK6 and LK8 units in a radio remote control ..................................... 4

5 Light signals .......................................................................................................... 5

6 General operating instructions ............................................................................ 7

6.1 Starting up the radio remote control ................................................................. 7

6.2 Command activation ........................................................................................ 9

6.3 Data Feedback Function .................................................................................. 9

6.4 Radio link interruption ...................................................................................... 9

6.5 Transmittingunitautomaticswitcho󰘯 .............................................................. 9

6.6 Switchingo󰘯thetransmittingunit................................................................... 10

7 Operation ............................................................................................................. 10

7.1 Battery ........................................................................................................... 10

7.2 ID internal tx memory ..................................................................................... 11

7.3 Power keyswitch ............................................................................................ 11

7.4 START pushbutton ........................................................................................ 13

7.5 FUNCTION pushbutton .................................................................................. 13

7.6 STOP pushbutton .......................................................................................... 13

8 Malfunction signalled by the transmitting unit ................................................. 14

AUTEC LILK6E00-01

Summary of content (16 pages)

PAGE 1
Original instructions Air series Part C: LK6 and LK8 transmitting units Index 1 Description ............................................................................................................. 2 2 Technical data ........................................................................................................ 3 3 Technical data sheet .............................................................................................. 3 4 Plates .....................................................
PAGE 2
Description 1 Description B M A L K C J H D E F G P N A Command pushbuttons H Power keyswitch (if present) B FUNCTION pushbutton J Battery C START pushbutton K D Technical data plate Actuator (selector, pushbutton) (if present) E Radio remote control identification plate L STOP pushbutton F Transmitting unit identification plate M LED G Battery housing N DIP switches P Connector for "ID internal tx memory" LILK6E00-01 AUTEC - Air series
PAGE 3
Technical data 2 3 Technical data Power supply (battery MHM03) ............................................................................... 3.6V Power supply (battery LPM01) ................................................................................ 3.7V Antenna ................................................................................................................... internal Housing material ...........................................................................................
PAGE 4
Plates 4 Plates 4.1 Plates on LK6 and LK8 units in a radio remote control Plate radio remote control identification plate transmitting unit identification plate technical data plate LILK6E00-01 Position Key ID 0-1 (if present). Battery housing (if the “ID internal tx memory” is present). Content Radio remote control serial number (S/N). Battery housing. Manufacturing year, bar code and transmitting unit identification number (TU ID). Battery housing.
PAGE 5
Light signals 5 5 Light signals In LK6 and LK8 transmitting units, a green LED [B] and a red LED [A] are always available, and they provide information regarding the radio remote control. The green LED [B] … …is off. ... is steady on. … blinks fast. … blinks slowly (one blink per second). The red LED [A]… …is off. A Red LED B Green LED C LEDs for Data Feedback function Meaning The transmitting unit is switched off. The transmitting and receiving unit do not communicate.
PAGE 6
Light signals LEDs … Meaning … the green [B] and red [A] LEDs are steady on A wrong "Key ID 0-1" or "ID internal tx memory" has been inserted in the transmitting unit, or this is a "BACK-UP UNIT". …the green [B] and red [A] LEDs blink 3 times per second during start up... The “Key ID 0-1” is damaged or the “ID internal tx memory” is damaged or not present. ... the green [B] and red [A] LEDs blink alternately. 30 s left before the transmitting unit automatically switches off.
PAGE 7
General operating instructions 6 7 General operating instructions 6.1 Starting up the radio remote control Starting up the radio remote control consists in establishing a radio link between the transmitting unit and the receiving unit. As required by standards IEC 60204-1 and IEC 60204-32, non authorised use of the machine must be prevented. The power keyswitch and/or the PIN CODE used for start up, make the radio remote control compliant with such requirement.
PAGE 8
6.1.2 General operating instructions PIN CODE start up (no power keyswitch) Consider that the transmitting unit will switch off 3 seconds after last activation of an actuator. When the receiving unit is powered on, perform the following procedure: 1. press the START pushbutton until the green LED illuminates 2. activate the commands corresponding to PIN CODE in the correct sequence (PIN 1, PIN 2 and PIN 3 given in the technical data sheet). a.
PAGE 9
General operating instructions 6.2 9 Command activation When the radio remote control is started, it is possible to move the pushbuttons and switches corresponding to the command you want to perform. The user must be properly trained about the symbols on the transmitting unit panel, to be aware of the matching between actuators and movements on the machine (symbols used are defined by the machine manufacturer according to the functions of the machine). 6.
PAGE 10
Operation 6.5.1 Low battery The transmitting unit indicates if the battery is not sufficiently charged (the red LED blinks fast): -- the red LED blinks slowly (one blink per second): the battery has less than 1h run time. -- the red LED blinks fast: the battery has a 10 minute run time from the first signal, after which the transmitting unit automatically switches off. The battery needs to be replaced with a charged one (see paragraph 7.1). 6.5.
PAGE 11
Operation 11 7.1.2 Battery removal Push the battery towards the contacts on the transmitting unit and remove it from the housing. 7.1.3 Battery run time indicator Perform the following procedure to check the run time of the battery in the transmitting unit: 1. switch off the transmitting unit and unlock the STOP pushbutton 2.
PAGE 12
Operation 7.3.5 BACK-UP UNIT If the main transmitting unit cannot be used because it has been lost or damaged, it can be replaced with a transmitting unit called "BACK-UP UNIT". It is identical to the unit that cannot be used anymore; the only difference is the presence of the plate “BACK-UP UNIT” on the battery housing. Set DIP switch 2 in the "BACK-UP UNIT" as shown in the technical data sheet.
PAGE 13
Operation 13 7.4 START pushbutton The START pushbutton is used to: -- start the radio remote control (see paragraph 6.1) -- activate the horn when the radio remote control is started. 7.5 FUNCTION pushbutton The FUNCTION pushbutton can be matched with different relay functions on the receiving unit (see technical data sheet). 7.6 STOP pushbutton The STOP pushbutton should be pressed when it is necessary to immediately stop the machine when a dangerous condition occurs.
PAGE 14
8 Malfunction signalled by the transmitting unit Malfunction signalled by the transmitting unit Use the light signals on the transmitting unit to identify the radio remote control malfunction. If the problem persists after the suggested solution has been carried out, contact the support service of the machine manufacturer. Signals Possible reason Solutions The transmitting and receiving unit do not communicate. Start up the radio remote control.
PAGE 15
Malfunction signalled by the transmitting unit Signals The green and red LEDs blink three times per second during start up. The green LED blinks and the red LED is steady on during start up. AUTEC - Air series Possible reason 15 Solutions The “Key ID 0-1” is damaged or the “ID internal tx memory” is damaged or not present. Contact the support service. The procedure corresponding to the UNPAIR submenu and given in the document "Menu of Transmitting Unit (MTU)" has been carried out.
PAGE 16