User's Manual

ManualsBrandsAutec ManualsElectronicsTransceiver unit

Original instructions

AIR SERIES

Part C: LK6, LK8 and LK6 DF transmitting units

INDEX

1 Description ............................................................................................................ 3

1.1 Description of units LK6 and LK8 ..................................................................... 3

1.2 Description of unit LK6 DF ............................................................................... 4

2 Technical data ....................................................................................................... 5

2.1 Technical data of units LK6 and LK8 ................................................................ 5

2.2 Technical data of unit LK6 DF .......................................................................... 5

3 Technical data sheet ............................................................................................. 5

4 Plates ..................................................................................................................... 6

4.1 Plates on units LK6, LK8 and LK6 DF belonging to a radio remote control

system ............................................................................................................. 6

4.2 Plates on units LK6, LK8 and LK6 DF belonging to a Take & Release system . 6

4.3 Plates on units LK6, LK8 and LK6 DF belonging to a Multi Units or Multi Receiver

system ............................................................................................................. 7

5 Light signals .......................................................................................................... 8

5.1 Light signals of units LK6 and LK8 ................................................................... 8

5.2 Light signals of unit LK6 DF ........................................................................... 10

6 General operating instructions .......................................................................... 13

6.1 Starting up the radio remote control ............................................................... 13

6.2 Command activation ...................................................................................... 15

6.3 Data Feedback Function ................................................................................ 15

6.4 Radio link interruption .................................................................................... 16

AUTEC LILK6E00-02

Summary of content (24 pages)

PAGE 1
Original instructions Air series Part C: LK6, LK8 and LK6 DF transmitting units Index 1 2 3 4 5 6 Description ............................................................................................................. 3 1.1 Description of units LK6 and LK8 ...................................................................... 3 1.2 Description of unit LK6 DF ................................................................................ 4 Technical data ...............................................
PAGE 2
7 8 6.5 Transmitting unit automatic switch off ............................................................. 6.6 Switching off the transmitting unit ................................................................... Operation .............................................................................................................. 7.1 Battery ............................................................................................................ 7.2 ID internal tx memory .........................
PAGE 3
Description 3 1 Description 1.
PAGE 4
Description 1.
PAGE 5
Technical data 2 Technical data 2.1 Technical data of units LK6 and LK8 5 Power supply (battery MHM03) ............................................................................... 3.6V Power supply (battery LPM01) ................................................................................ 3.7V Antenna ................................................................................................................... internal Housing material .....................................................
PAGE 6
Plates 4 Plates 4.1 Plates on units LK6, LK8 and LK6 DF belonging to a radio remote control system Plate Position Content Key ID 0-1 (if present). radio remote control identification plate 4.2 Battery housing (if the “ID internal tx memory” is present). Radio remote control serial number (S/N). transmitting unit identification plate Battery housing. Manufacturing year, bar code and transmitting unit identification number (TU ID). technical data plate Battery housing.
PAGE 7
Plates 4.3 7 Plates on units LK6, LK8 and LK6 DF belonging to a Multi Units or Multi Receiver system Plate Position Content Key ID 0-1 (if present). radio remote control identification plate Battery housing (if the “ID internal tx memory” is present). Radio remote control serial number (MULTI S/N). transmitting unit identification plate Battery housing. Manufacturing year, bar code and transmitting unit identification number (TU ID). technical data plate Battery housing.
PAGE 8
Light signals 5 Light signals 5.1 Light signals of units LK6 and LK8 In LK6 and LK8 transmitting units, a green LED [B] and a red LED [A] are always available, and they provide information regarding the radio remote control. Symbol A Red LED B Green LED C LEDs for Data Feedback function Meaning This symbol indicates the red LED [A]. This symbol indicates the green LED [B]. The green LED [B] … …is off. ... is steady on. … blinks fast. … blinks slowly (one blink per second).
PAGE 9
Light signals 9 The red LED [A]… …is off. Meaning The transmitting unit works correctly. ... is steady on. At start-up, the STOP pushbutton is pressed or damaged. ... blinks twice per second. At least one of the commands that were checked at startup is enabled or damaged (see technical data sheet). ... blinks three times per second. ... is steady on for 2s. … blinks slowly (one blink per second). ... blinks fast. At start-up,the battery is flat. The transmitting unit does not work correctly.
PAGE 10
5.2 Light signals Light signals of unit LK6 DF Display icons A Red LED B Green LED D Battery E Radio link The following icons are always available on the display of LK6 DF transmitting units: -- Red LED [A] and green LED [B] providing information about the radio remote control -- Battery [D] providing indication of the battery power level -- Radio link [E] providing indication of radio link strength.
PAGE 11
Light signals 11 The red LED [A]… …is off. Meaning The transmitting unit works correctly. ... is steady on. At start-up, the STOP pushbutton is pressed or damaged. ... blinks twice per second. At least one of the commands that were checked at startup is enabled or damaged (see technical data sheet). ... blinks three times per second. ... is steady on for 2s. … blinks slowly (one blink per second). ... blinks fast. At start-up,the battery is flat. The transmitting unit does not work correctly.
PAGE 12
Light signals 5.2.3 Radio link [E] Radio link [E] icon consists of four vertical bars. The amount of dark bars is proportional to the quality of radio link. Symbol Meaning Strong radio link signal. Medium radio link signal. No radio link.
PAGE 13
General operating instructions 6 13 General operating instructions 6.1 Starting up the radio remote control Starting up the radio remote control consists in establishing a radio link between the transmitting unit and the receiving unit. As required by standards IEC 60204-1 and IEC 60204-32, non authorised use of the machine must be prevented. The power keyswitch and/or the PIN CODE used for start up, make the radio remote control compliant with such requirement.
PAGE 14
6.1.2 General operating instructions PIN CODE start up (no power keyswitch) Consider that the transmitting unit will switch off 3 seconds after last activation of an actuator. When the receiving unit is powered on, perform the following procedure: 1. press the START pushbutton until the green LED illuminates 2. activate the commands corresponding to PIN CODE in the correct sequence (PIN 1, PIN 2 and PIN 3 given in the technical data sheet). a.
PAGE 15
General operating instructions 6.2 15 Command activation When the radio remote control is started, it is possible to move the pushbuttons and switches corresponding to the command you want to perform. The user must be properly trained about the symbols on the transmitting unit panel, to be aware of the matching between actuators and movements on the machine (symbols used are defined by the machine manufacturer according to the functions of the machine). 6.
PAGE 16
General operating instructions 6.4 Radio link interruption When the radio link is incorrect or interrupted, the receiving unit autonomously stops the radio remote control. The green LED on the transmitting unit switches from blinking slowly to fast blinking or steady on. Press the START pushbutton to start the radio remote control. 6.5 Transmitting unit automatic switch off The transmitting unit automatically switches off when: -- the battery is flat (see paragraph 6.5.
PAGE 17
Operation 17 7 Operation 7.1 Battery The Air series' transmitting units can only be powered by Autec rechargeable batteries. See the battery charger manual enclosed in the packaging with the battery charger for any warnings and instructions regarding the batteries. 7.1.1 Battery insertion Push the battery towards the contacts on the transmitting unit and insert it inside the housing. 7.1.2 Battery removal Push the battery towards the contacts on the transmitting unit and remove it from the housing.
PAGE 18
Operation 7.2 ID internal tx memory The transmitting unit may require the "ID internal tx memory", where the radio remote control's address is stored.The technical data sheet indicates if the "ID internal tx memory" is required. 7.3 Power keyswitch The transmitting unit may have a power keyswitch. It can either be: -- mechanical key (see paragraph 7.3.1) -- Key ID 0-1 (see paragraph 7.3.2). 7.3.1 Mechanical key The mechanical key makes it possible to power the transmitting unit.
PAGE 19
Operation 19 7.3.5 BACK-UP UNIT If the main transmitting unit cannot be used because it has been lost or damaged, it can be replaced with a transmitting unit called "BACK-UP UNIT". It is identical to the unit that cannot be used anymore; the only difference is the presence of the plate “BACK-UP UNIT” on the battery housing. Set DIP switch 2 in the "BACK-UP UNIT" as shown in the technical data sheet.
PAGE 20
Operation 7.4 START pushbutton The START pushbutton is used to: -- start the radio remote control (see paragraph 6.1) -- activate the horn when the radio remote control is started. 7.5 FUNCTION pushbutton The FUNCTION pushbutton can be matched with different relay functions on the receiving unit (see technical data sheet). 7.6 STOP pushbutton The STOP pushbutton should be pressed when it is necessary to immediately stop the machine when a dangerous condition occurs.
PAGE 21
Malfunction signalled by the transmitting unit 8 21 Malfunction signalled by the transmitting unit Use the light signals on the transmitting unit to identify the radio remote control malfunction. If the problem persists after the suggested solution has been carried out, contact the support service of the machine manufacturer. Signals Possible reason Solutions The transmitting and receiving unit do not communicate. Start up the radio remote control.
PAGE 22
Malfunction signalled by the transmitting unit Signals The green and red LEDs blink three times per second during start up. The green LED blinks and the red LED is steady on during start up. LILK6E00-02 Possible reason Solutions The “Key ID 0-1” is damaged or the “ID internal tx memory” is damaged or not present. Contact the support service. The procedure corresponding to the UNPAIR submenu and given in the document "Menu of Transmitting Unit (MTU)" has been carried out.
PAGE 23
PAGE 24