User's Manual

ManualsBrandsAutec ManualsElectronicsTransceiver unit

Original instructions

AIR SERIES

Part C: AJS transmitting unit

INDEX

1 Description ............................................................................................................ 2

2 Technical data ....................................................................................................... 3

3 Technical data sheet ............................................................................................. 3

4 Plates ..................................................................................................................... 4

4.1 Plates on AJS unit in a radio remote control .................................................... 4

4.2 Plates on AJS unit in a Take & Release system ............................................... 4

4.3 Plates on AJS unit in a Multi Units or Multi Receiver system ............................ 5

5 Light signals .......................................................................................................... 6

6 General operating instructions ............................................................................ 7

6.1 Starting up the radio remote control ................................................................. 7

6.2 Command activation ........................................................................................ 8

6.3 Data Feedback Function .................................................................................. 8

6.4 Radio link interruption ...................................................................................... 9

6.5 Transmitting unit automatic switch o󰘯 .............................................................. 9

6.6 Switching o󰘯 the transmitting unit ..................................................................... 9

7 Operation ............................................................................................................. 10

7.1 Battery ........................................................................................................... 10

7.2 Air-KEY .......................................................................................................... 11

7.3 START pushbutton ........................................................................................ 12

7.4 STOP pushbutton .......................................................................................... 12

7.5 DISPLAY pushbutton (if the transmitting unit has a display) ........................... 13

8 Malfunction signalled by the transmitting unit ................................................. 14

AUTEC LIAJSE00-00

Summary of content (16 pages)

PAGE 1
Original instructions AIR SERIES Part C: AJS transmitting unit INDEX 1 2 3 4 5 6 7 8 Description ............................................................................................................. 2 Technical data ........................................................................................................ 3 Technical data sheet .............................................................................................. 3 Plates ..................................................
PAGE 2
LIAJSE00-00 A LEDs B STOP pushbutton C Display or LED (if present) D Actuators (joysticks, selectors, pushbuttons) E FUNCTION pushbutton F Battery G Technical data plate 7.2V AIRTR42DM 2 4 O ST TAXXXX-XX A0TARG01P0XXX 3 This radio device complies with Part 15 of the FCC Rules.
PAGE 3
Technical data 2 3 Technical data Power supply (battery LPM02) ...................................................................... Li-Ion 7.4V Power supply (battery MBM06MH) ................................................................ NiMH 7.2V Antenna ................................................................................................................... internal Housing material ...........................................................................................
PAGE 4
Plates 4 Plates 4.1 Plates on AJS unit in a radio remote control Plate Content On the Air-KEY: remove the Air-KEY to read the plate. Radio remote control serial number (S/N). transmitting unit identification plate In the battery housing: remove the battery to read the plate. Manufacturing year, bar code and transmitting unit identification number (TU ID). technical data plate In the battery housing: remove the battery to read the plate.
PAGE 5
Plates 4.3 5 Plates on AJS unit in a Multi Units or Multi Receiver system Plate Position Content On the Air-KEY: remove the Air-KEY to read the plate. System serial number (MULTI S/N). transmitting unit identification plate In the battery housing: remove the battery to read the plate. Manufacturing year, bar code and transmitting unit identification number (TU ID). technical data plate In the battery housing: remove the battery to read the plate.
PAGE 6
5 Light signals Light signals In AJS transmitting units, a green and a red LED are always available, providing information regarding the radio remote control. The green LED… …is off. A Red LED B Green LED Meaning The transmitting unit is switched off. ... is steady on. The transmitting and receiving unit do not communicate. … blinks fast. The transmitting and receiving unit communicate. It is possible to start the radio remote control by pressing the START pushbutton.
PAGE 7
General operating instructions 6 7 General operating instructions Starting up the radio remote control consists in building a radio link between the transmitting and the receiving unit. 6.1 Starting up the radio remote control As required by standard IEC 60204-32, the radio remote control start up is protected in order to prevent unauthorised use of the machine. A removable key called Air-KEY guarantees such protection. The radio remote control cannot work without it.
PAGE 8
6.2 General operating instructions Command activation With the radio remote control started, act on the joysticks, pushbuttons and switches corresponding to the command to be performed. The user must be properly trained about the symbols on the transmitting unit panel, to be aware of the matching between actuators and movements on the machine (symbols used are defined by the machine manufacturer according to the functions of the machine). 6.
PAGE 9
General operating instructions 6.4 9 Radio link interruption When the radio link is incorrect or interrupted, the receiving unit autonomously stops the radio remote control. The green LED on the transmitting unit switches from blinking slowly to fast blinking or steady on. Press the START pushbutton to start the radio remote control. 6.5 Transmitting unit automatic switch off The transmitting unit automatically switches off when: -- the battery is flat (see paragraph 6.5.
PAGE 10
7 7.1 Operation Operation Battery The Air series' transmitting units can only be powered through Autec rechargeable batteries. See the battery charger manual enclosed in the packaging with the battery charger for any warnings and instructions regarding the batteries. 7.1.1 Battery insertion Push the battery towards the contacts on the transmitting unit (1) and insert it inside the housing (2). 7.1.
PAGE 11
Operation 7.2 11 Air-KEY In the transmitting unit, the radio remote control address is stored in the Air-KEY. For this reason, the radio remote control cannot work without this key. The Air-KEY can only be used in the transmitting unit of the radio remote control where it belongs. As the radio remote control address is stored in the Air-KEY, use it with utmost care to reduce risks that may result from incorrect handling. 7.2.
PAGE 12
Operation Address storage When the battery is charged and the Air-KEY is in the "BACK-UP UNIT", perform the following procedure to store the address: 1. press the START pushbutton until the green and the red LEDs illuminate and an acoustic signal sounds 2. wait until the green LED blinks slowly 3. within 3 seconds, activate in sequence the commands corresponding to PIN 1, PIN 2 and PIN 3 that compose the PIN code given in the technical data sheet.
PAGE 13
Operation 7.5 13 DISPLAY pushbutton (if the transmitting unit has a display) This pushbutton is used to: -- activate the display lighting, if it is off -- cyclically scroll the information on the display in two different modes -- manual: the lines scroll up each time the pushbutton is pressed -- automatic: when the DISPLAY pushbutton is pressed for 3 seconds, the lines scroll automatically. If the DISPLAY pushbutton is pressed another time, it switches back to manual mode.
PAGE 14
8 Malfunction signalled by the transmitting unit Malfunction signalled by the transmitting unit Use the light signals on the transmitting unit to identify the radio remote control malfunction. If the problem persists after the suggested solution has been carried out, contact the support service of the machine manufacturer. Signals Possible reason Solutions The transmitting and receiving unit do not communicate. Start up the radio remote control.
PAGE 15
Malfunction signalled by the transmitting unit 15 Signals Possible reason The green and red LEDs blink three times per second during start up. The Air-KEY is damaged. Contact the support service. The red LED is steady on for two seconds. The transmitting unit does not work correctly. Contact the support service. The red LED blinks slowly (one blink per second). The battery has a 2h run time. Replace the battery with a charged one within 2h. The red LED blinks quickly.
PAGE 16