IN600 AV SYSTEM CONTROLLER INSTALLATION AND OPERATION MANUAL
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION 1. Read these instructions. 1. LISEZ ces instructions. 2. Keep these instructions. 2. Tenez ces instructions. 3. Heed all warnings. 3. Notez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les avertissements. 5. Do not use this apparatus near water. 5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.). 6. Clean only with dry cloth. 6. Nettoyez seulement avec une étoffe sèche.
INTRODUCTION AND CONTENTS The Innovation series from AMAV is a huge step forward in the interfacing and management of audio and visual sources. Integrating a host of smart, high end features in a compact package that offers the end user extremely simple control over their complex audio visual system. The Innovation series is as ground breaking as it is simple to operate. The IN600 takes the Innovations series concept to the next level in terms of flexibility and complete system control.
FRONT PANEL 4 3 7 11 9 10 8 12 1 2 6 1 GAIN TRIM This control is used to adjust the input gain and affects both the XLR and the RCA inputs. The input gain can be adjusted by +/- 15dB. This allows a wide rage of program sources to be set up with optimum gain structure. With the gain trim in the centre position, the boost/cut is set to 0dB. 2 LEVEL Controls the level of the input signal. 3 INPUT STATUS LEDS Each input has an LED status indicator.
REAR PANEL 16 15 14 17 5 7 6 4 1 CHANNEL INPUTS Each channel has two inputs: XLR input - This is a balanced input. It accepts mic or line level signals depending on the adjacent gain switch position. The XLR will also have +15V phantom power if selected on the adjacent switch. RCA input - This is an unbalanced line level input. The two RCA sockets are summed to mono internally.
INSTALLATION All installation work should be done with the power disconnected. The following information will help with installation. After installation is complete power up in the following order: 1. All the sources 2. IN600 3. All amplifiers POWER CONNECTION BREAK OUT CABLE Component video can be used on the IN600 by using a VGA break out cable. A break out cable is required for all devices. There is no internal VGA to component conversion within the IN600. (ie.
RS485 COMMANDS Data: 19200, 8N1 All ASCII characters The commands are pure ASCII. So a hex value of 0xA5 (decimal 165) is sent as ASCII ‘A’ ‘5’, or 0x41 0x35.
SETUP / SOFTWARE The IN600 software come included on a CD ROM. The IN600 software will work on any windows XP or later operating system. Installing the software is easy insert the CD and run the setup.exe file. Follow the prompts. You should close down the software before disconnecting the IN600 from the USB port.The IN600 can be safely connected and disconnect from the USB port at anytime when the software is not running.
SETUP / SOFTWARE CONTINUED 1 2 3 4 File menu This menu contains the standard Windows File options. 1 Open Opens a .in6 file which contains a previously save configuration of the software. Opening a file will overwrite your current configuration. If the IN600 is Online then opening a file will load the contents straight up to the IN600. 2 Save This will prompt you to save the file with the name of the open file. If no file has been opened you can save it as any name.
SETUP / SOFTWARE CONTINUED 1 2 3 4 3 Configuration menu 1 Set Projector Codes This menu item will open the Projector Setup window. 2 Set Input Names Allows you to set the names of the Mic/Line inputs and the AV sources. These are stored in the EEPROM of the IN600 itself and is limited to 8 charaters. 3 Set Power Up Values This button opens a window to configure the power up settings. The power up settings is the way the unit will be set after powering up.
SETUP / SOFTWARE CONTINUED Project Setup window This window allows you to set the parameters of the RS232 port used to connect to a projector. You can set all the parameters of the communication protocol; Baud Rate, Parity, No of Data Bits, No of Stop Bits. 1 2 3 1 Projector Timeouts 3 Screen This is the number of seconds (integer values only) that the IN600 will wait before allowing another command to be set to the projector when an On/Off command is sent.
INTERNAL ADJUSTMENTS 1 2 3 The following routing configurations can be made inside the IN600. Access to the inside the the IN600 should only be performed by a qualified person. 1 Mic/Line HPF Each of the 4 mic/line inputs has a 150Hz HPF. Moving the jumper to the IN position will enable the filter. The factory default is OUT. 2 Mic/Line mix to... The mic/line mix can be sent to the the surround sound left and right and/or the sub output. There are 3 jumpers with two postions, on or off.
BLOCK DIAGRAM IN600 INSTALLATION AND OPERATION MANUAL PAGE 13
DIMENSIONS PAGE 14 IN600 INSTALLATION AND OPERATION MANUAL
SPECIFICATIONS Line Audio THD Noise Floor Frequency Response (+/-3dB) Gain (trim centre) Headroom <0.5% -90dBu 20-20kHz XLR Mic 45dB XLR Line 0dB RCA line 12dB RCA switched 0dB 15dBu Video VGA Video Video follows Audio switching Comms Type Baud Rate No of Data Bit Parity No of Stop Bits RS485 19200 8 None 1 Power Consumption (max) 30VA Thermal output SIZE (WXHXD) High speed RGB+Sync switching Composite 75ohm Buffered outputs 1/8th power 100W (341.2Btu/hr) 482 x 88 x 270mm 19.” x 3.5” x 9.
AUSTRALIA AND NEW ZEALAND www.australianmonitor.com.au SYDNEY MELBOURNE ADELAIDE AUCKLAND (NSW SALES) (VIC & TAS SALES) (SA & NT SALES) (NZ SALES) 1 Clyde Street Silverwater NSW 2128 Private Bag 149 Silverwater NSW 1811 Phone: (02) 9647 1411 Fax: (02) 9648 3698 Email: nsw@audiotelex.com.au 22/277 Middleborough Road Box Hill VIC 3128 PO Box 151 Blackburn South VIC 3130 Phone: (03) 9890 7477 Fax: (03) 9890 7977 Email: vic@audiotelex.com.
