User's Manual

ManualsBrandsAurum Electronics ManualsElectronicsTHE INTELLIGENT MOTION SENSOR TRACKING LIGHT-Receiver

THE INTELLIGENT

MOTION SENSOR TRACKING LIGHT

INSTALLATION INSTRUCTIONS

Read all instructions before proceeding with the installation

OVERVIEW OF AEC-9336CU

INSTALLING THE BULB

 Unscrew the lamp cover of the luminaire and install a 150W J-type lamp.

 Re-fit the lamp cover and tighten the screws.

IMPORTANT: THE INTALLATION OF THIS FITTING MUST BE DONE BY A QUALIFIED ELECTRICIAN.

 This fitting must be earthed.

 Do not mount the luminaire against inflammable surfaces.

 The motion detector will not operate correctly if it is installed:

( ) Near the outlet of a central heating boiler Ⅰ

( ) Near air conditioning plant Ⅱ

( ) Pointing directly at moving vehicles Ⅲ

( ) Within sight Ⅳ of reflection from moving water

( ) Where other lamps could shine onto the detectorⅤ

 The maximum rating of this luminaire is 150 Watts. Check that the total load of the circuit. Including this luminaire. Does not

exceed the rating of the circuit cable.

NOTE: This highly responsive unit may occasionally activate due to rapid environmental changes. Allow for approximately 30

seconds warm-up time before the sensor resumes normal activity.

WARNING ! ! !

BEFORE ATTEMPTING ANY INSTALLATION OR

MAINTENANCE, ENSURE THAT THE

ELECTRICAL SUPPLY IS SWITCHED OFF AND

THE CIRCUIT FUSES REMOVED OR THE

CIRCUIT BREAKER IS IN THE “OFF”POSITION.

Video Camera

Sensor

LED indicator

Dip Switch

Antenna

Front housing

Lamp 150W

Lamp Cover

Summary of content (8 pages)

PAGE 1
THE INTELLIGENT MOTION SENSOR TRACKING LIGHT INSTALLATION INSTRUCTIONS Read all instructions before proceeding with the installation OVERVIEW OF AEC-9336CU Lamp Cover Front housing Lamp 150W Antenna Video Camera Dip Switch Sensor LED indicator INSTALLING THE BULB Unscrew the lamp cover of the luminaire and install a 150W J-type lamp. Re-fit the lamp cover and tighten the screws. IMPORTANT: THE INTALLATION OF THIS FITTING MUST BE DONE BY A QUALIFIED ELECTRICIAN.
PAGE 2
MOUNTING THE FITTING To ensure correct operation of the sensor, mount the luminaire that traffic passes across the detector. TOP VIEW GOOD SENSITIVITY LESS SENSITIVITY SETTING THE LIGHT UP TIME & SENSITIVTY Remove the back mounting box from the fixture by unscrewing the screw at the bottom. Set the Light up time & Sensitivity you preferred １： Light up time (OFF： 30 seconds／ ON： 60 seconds) ２： Sensitivity (OFF： 5m／ ON： 10 m) Re-fit the back mounting box and tighten the screw.
PAGE 3
FUNCTION This light is equipped with 3 motion sensors: zone 1 covers 60 degree, zone 2 covers 100 degrees and zone 3 covers 60 degrees. 220 degrees (maximum) in total for 3 zones. ZONE 2 ZONE 1 ZONE 3 TOTAL DETECTION RANGE The light will switch on for 30 /60 seconds and off automatically when heat/ movement is detected. The factory default: the mode is「Auto mode」for light works at night, camera works all day.
PAGE 4
OPERATION 1. Insert the plug to activate the light, the light is now under Test mode: light works on day and night NOTE: Allow for approximately 30 seconds warm-up time before the sensor resumes normal activity. 2. To test, walk through the sensor’s detection area. 3. Movement will activate the sensor and turn the light on, the light will turn the face to the detected zone. 4.
PAGE 5
F. Installing the Driver on your computer Place CD driver into the Computer CD slot and installing. Choice the software you use for your computer. Follow the instructions on the installation screen ¾ Click Setup_090817.exe（fig 1）→ Next（Fig. 2）→ Next （Fig. 3）→ Install（Fig. 4） →Finish（Fig. 5）→ Restart windows. ¾ If your computer doesn’t run the installation program automatically, please click the “Start” button and choose “Run.” Then browse your computer to find CD slot and Driver and click “Setup”. Fig.
PAGE 6
G. Installing the driver of 752C ¾ Installing the Drive, please refer above “Installing the Driver on your computer”. Assembly and power on the 9336C. Please refer assembly of 9336C. Please re-install the driver of 752C if appear this software cannot find. ¾ Plug 752C into a USB port on your PC and follow the instructions on the installation screen as fig. 6 ~ 11. Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig.
PAGE 7
Device Setup（Fig. 14）→ Choice channel CH1～ CH4（Fig. 15）→ Press 9336C of top button and when the video is shown on the screen the setup is completed（Fig. 16）→ then click OK（Fig. 17）。 Fig. 12 Fig. 14 Fig. 15 Fig. 16 Fig. 17 H. Definition of Driver of 752C Fig.
PAGE 8
¾ B：Multi files save Preview：Shooting / Recording mode ¾ C : Auto recording ¾ D：Manual recording - Capture Photo ¾ E：Manual recording - Recording video Setup：Channel Column Channel 1：Set up Channel ¾ F：It can select Channel 1〜4 of Single view or 4 quad view Alarm ¾ G / H：Alarm ON / OFF ¾ J：When TX detected, one of channel 1〜 4 will turn to Red background. Signal Intensity Display ¾ I：RX and TX of transmission signal.