User's Manual

ManualsBrandsAurum Electronics ManualsElectronicsThe Intelligent Motion Sensor Tracking Light (Transmitter）

THE INTELLIGENT

MOTION SENSOR TRACKING LIGHT

INSTALLATION INSTRUCTIONS

Read all instructions before proceeding with the installation

OVERVIEW OF AEC-9339A

INSTALLING THE BULB

 Unscrew the lamp cover of the luminaire and

install a 300W J-type lamp.

 Re-fit the lamp cover and tighten the screws.

IMPORTANT: THE INTALLATION OF THIS FITTING MUST BE DONE BY A QUALIFIED ELECTRICIAN.

 This fitting must be earthed.

 Do not mount the luminaire against inflammable surfaces.

 The motion detector will not operate correctly if it is installed:

( ) Near the outlet of a central heating boiler Ⅰ

( ) Near air conditioning plant Ⅱ

( ) Pointing directly at moving vehicles Ⅲ

( ) Within sight of reflection from moving waⅣ ter

( ) Where other lamps could shine onto the detectorⅤ

 The maximum rating of this luminaire is 300 Watts. Check that the total load of the circuit. Including this luminaire.

Does not exceed the rating of the circuit cable.

NOTE: This highly responsive unit may occasionally activate due to rapid environmental changes. Allow for approximately

30 seconds warm-up time before the sensor resumes normal activity.

Push-button

3 motion sensors

WARNING ! ! !

BEFORE ATTEMPTING ANY INSTALLATION OR

MAINTENANCE, ENSURE THAT THE

ELECTRICAL SUPPLY IS SWITCHED OFF AND

THE CIRCUIT FUSES REMOVED OR THE

CIRCUIT BREAKER IS IN THE “OFF”POSITION.

(DRAFT)

Summary of content (8 pages)

PAGE 1
THE INTELLIGENT MOTION SENSOR TRACKING LIGHT (DRAFT) INSTALLATION INSTRUCTIONS Read all instructions before proceeding with the installation OVERVIEW OF AEC-9339A Push-button 3 motion sensors INSTALLING THE BULB Unscrew the lamp cover of the luminaire and install a 300W J-type lamp. Re-fit the lamp cover and tighten the screws. IMPORTANT: THE INTALLATION OF THIS FITTING MUST BE DONE BY A QUALIFIED ELECTRICIAN. This fitting must be earthed.
PAGE 2
MOUNTING THE FITTING To ensure correct operation of the sensor, mount the luminaire that traffic passes across the detector. TOP VIEW GOOD SENSITIVITY LESS SENSITIVITY INSTALLATION AND WIRING INSTRUCTIONS Remove the inset back mounting box from the luminaire. Fit the inset back mounting box onto the wall and tighten the screws at a height that ensures adequate coverage of the area by the infrared detector. The minimum installation height is 2 meters. And the maximum height is 3 meters.
PAGE 3
FUNCTION This light is equipped with 3 motion sensors: zone 1 covers 60 degree, zone 2 covers 100 degrees and zone 3 covers 60 degrees. 220 degrees (maximum) in total for 3 zones. ZONE 2 ZONE 1 ZONE 3 TOTAL DETECTION RANGE The light will switch on for 3 minutes and off automatically when heat/ movement is detected. The factory default: the light on fixed at 3 minutes and works all day.
PAGE 4
OPERATION 1. Turn on the wall switch to activate the light, the light is now under All Day mode: light works on day and night NOTE: Allow for approximately 30 seconds warm-up time before the sensor resumes normal activity. 2. To test, walk through the sensor’s detection area. 3. Movement will activate the sensor and turn the light on, the light will turn the face to the detected zone for approx. 3 minutes. 4.
PAGE 5
THE INTELLIGENT MOTION SENSOR TRACKING LIGHT (DRAFT) INSTALLATION INSTRUCTIONS Read all instructions before proceeding with the installation OVERVIEW OF AEC-9336A Push-button 3 motion sensors INSTALLING THE BULB Unscrew the lamp cover of the luminaire and install a 150W J-type lamp. Re-fit the lamp cover and tighten the screws. IMPORTANT: THE INTALLATION OF THIS FITTING MUST BE DONE BY A QUALIFIED ELECTRICIAN. This fitting must be earthed.
PAGE 6
MOUNTING THE FITTING To ensure correct operation of the sensor, mount the luminaire that traffic passes across the detector. TOP VIEW GOOD SENSITIVITY LESS SENSITIVITY INSTALLATION AND WIRING INSTRUCTIONS Remove the inset back mounting box from the luminaire. Fit the inset back mounting box onto the wall and tighten the screws at a height that ensures adequate coverage of the area by the infrared detector. The minimum installation height is 2 meters. And the maximum height is 3 meters.
PAGE 7
FUNCTION This light is equipped with 3 motion sensors: zone 1 covers 60 degree, zone 2 covers 100 degrees and zone 3 covers 60 degrees. 220 degrees (maximum) in total for 3 zones. ZONE 2 ZONE 1 ZONE 3 TOTAL DETECTION RANGE The light will switch on for 3 minutes and off automatically when heat/ movement is detected. The factory default: the light on fixed at 3 minutes and works all day.
PAGE 8
OPERATION 1. Turn on the wall switch to activate the light, the light is now under All Day mode: light works on day and night NOTE: Allow for approximately 30 seconds warm-up time before the sensor resumes normal activity. 2. To test, walk through the sensor’s detection area. 3. Movement will activate the sensor and turn the light on, the light will turn the face to the detected zone for approx. 3 minutes. 4.