MCD-107C Kompakt-Anlage 10028090 www.auna-multimedia.
Sehr geehrter Kunde, zunächst möchten wir Ihnen zum Erwerb Ihres Gerätes gratulieren. Bitte lesen Sie die folgenden Anschluss- und Anwendungshinweise sorgfältig durch und befolgen Sie diese um möglichen technischen Schäden vorzubeugen. Sicherheitshinweise und Gewährleistung • • • • • • • • • • • • Diese Bedienungsanleitung dient dazu, Sie mit der Funktionsweise dieses Produktes vertraut zu machen. Bewahren Sie diese Anleitung daher stets gut auf, damit Sie jederzeit darauf zugreifen können.
Technische Daten Artikelnummer 10028090 Gerätetyp Anschlüsse Kompaktanlage 2 x Stereo-Lautsprecherklemme; 2x LED-Anschluss; Netzanschluss Stromversorgung Netzkabel, ~230V Lieferumfang Bedienelemente Front: 3
Standby-LED 1 12 Infrarot-Sensor (Fernbedienung) (Einschalten / Standby) 2 13 FUNC Display 3 14 VOL + / - 4 15 EQ / ST/MONO 5 16 DISPLAY / ID3 MEM / CLK (Uhrzeit einstellen) 6 17 CD OPEN/CLOSE PLAY MODE 7 18 Kopfhörer-Anschluss 8 19 AUX-Anschluss 9 20 USB-Anschluss 10 21 SD-Kartenslot FOLDER / PRE / LIGHT / TIMER / CD-Lade Rückseite: 4 11
Antenne 22 24 Anschlussbuchse für LED-Beleuchtung Lautsprecher-Anschlussklemmen 23 25 Netzanschluss Fernbedienung: I/ Ein-/ausschalten MEM / CLK ADJ Standby: Gedrückt halten zum Einstellen d.
Inbetriebnahme • Setzen Sie zwei Batterien vom Typ „AAA“ (nicht im Lieferumfang enthalten) in die Fernbedienung ein.
• Beleuchtung: • Verbinden Sie dann das mitgelieferte Netzteil mit dem Gerät und einer Haushaltssteckdose. Schalten Sie das Gerät mit ein.
Funktionen Einstellen der Uhrzeit • • • Schalten Sie das Gerät in den Standby-Modus ( ). Drücken Sie MEM/CLK ADJ. „SET CLOCK“ und „24hr“ werden auf dem Display angezeigt. Wählen Sie mit / das Uhrzeitformat (12h/24h). Drücken Sie MEM/CLK ADJ, um die Uhrzeit zu ändern. Zunächst stellen Sie mit / die Stunden ein. Speichern und fahren Sie mit erneutem Druck auf MEM/CLK ADJ fort. Wiederholen Sie dann den Vorgang für die Einstellung der Minuten. Speichern Sie wiederum mit MEM/CLK. Bitte beachten Sie: 1.
CDs / MP3s (USB/SD) • • Wählen Sie den CD-/USB-/SD-Modus mit der FUNCTION Taste aus. • Öffnen Sie das CD-Fach mit OPEN und legen Sie eine CD (mit der bedruckten Seite nach oben) ein. • Stecken Sie eine Musik enthaltende SD-Karte oder einen USB-Stick (bzw. MP3-Player o.ä.) ein. Navigieren Sie mit den gewohnten Tasten , / und . Nutzen Sie bei MP3-CDs die Pfeiltasten ( / ) für die Auswahl des Ordners. ID3/Display Drücken Sie ID3/DISPLAY, um (vorhandene) ID3-Tags auf dem Display anzuzeigen.
BT • • • • Wählen Sie den BT-Modus mit FUNCTION aus. Aktivieren Sie die BT-Funktion Ihres Tablets/Mobiltelefon/Laptop und verbinden Sie mit MCD-107C. Bei erfolgreichem Verbindungsaufbau zeigt das Display „BT“ an. Sie können , / und . nutzen, um durch Ihre mobile Musikbibliothek zu navigieren, oder das externe Gerät dafür verwenden. Halten Sie für einen Moment gedrückt, um die Verbindung zu trennen, falls Sie ein anderes BTGerät verbinden möchten.
Display: Drücken Sie in jedem Modus DISPLAY, um die Uhrzeit auf dem Display anzuzeigen Mute: Drücken Sie MUTE, um die Musikausgabe stumm zu schalten / die Stummschaltung zu beenden. AUX-IN: Schließen Sie externe Abspielgeräte (MP3-Player, Laptops, Smartphones etc.) mit einem AudioKabel hier an. Drücken Sie mehrfach FUNCTION, um in den AUX-Modus zu gelangen.
Dear Customer, Congratulations on purchasing this product. Please read and follow these instructions, in order to avoid damaging the item. We do not cover any damages that may arise from improper use of the item or the disregard of the safety instructions. Important Safety Advice • • • • • • • • • Read all instructions before using. To protect against a fire, electric shock or personal injury, do not immerse cord, electric plugs or device in water or other liquids.
Technical Data Article # Connections Power supply 10028090 2 x Stereo speaker terminal 2x LED power jacks (3.
Standby LED 1 12 IR Sensor (On / Standby) 2 13 FUNCTION Display 3 14 VOL + / - 4 15 EQ / ST/MONO 5 16 DISPLAY / ID3 MEM / CLK 6 17 CD OPEN/CLOSE PLAY MODE 7 18 Headphone jack 8 19 AUX in jack 9 20 USB port 10 21 SD card slot FOLDER / PRE / LIGHT / TIMER / CD Tray Rear: 14 11
Antenna 22 24 3.
Setup / Initial Use • Insert two AAA size batteries (not included) into the remote control battery compartment following the polarity markings inside the battery compartment. • • Connect the AC cord to the wall outlet. When you first plug the unit into the mains, the unit will go into standby mode and the standby LED indicator (1) will light up. Connect the speaker wire to the speaker terminals (23) located on the back of the unit and connect the lighting wire with the 3.
Funktionen Einstellen der Uhrzeit • • • Set the unit into standby mode ( ). Press MEM/CLK ADJ. „SET CLOCK“ and „24hr“ will be displayed. Use / to change the time format (12h/24h). Press MEM/CLK ADJ, To set the time. First, set the hour using / . Then save with MEM/CLK ADJ and repeat for setting the minutes. Save changes with MEM/CLK. Please note: 1. The clock setting mode will automatically quit if no button is being pressed in a period of about 10 seconds after pressing the “ Mem/Clk-adj ” button. 2.
CDs / MP3s (USB/SD) • • Choose the CD/USB/SD mode pressing FUNCTION repeatedly. • Press OPEN to open the CD tray and put in a CD (with the printed side facing up) or • Insert an SD card or a USB drive containing MP3 or WAV files. Navigate, conveniently using , / and . For MP3 CDs, USB drives and SD cards, use / to change folders. ID3/Display Press ID3/DISPLAY to show any available ID3 tags on the display. Press again to stop displaying ID3 tags.
BT • • • • Press FUNCTION repeatedly to choose BT mode. Activate BT on your mobile device and connect with MCD-107C. The display shows „BT“ on successfull connection attempt. Use , / and . to navigate through your mobile music library, or use the external device, alternatively. Press and hold to disconnect, if you want to pair with another BT device. Sleep Timer / Timer • Press SLEEP (on the RC) repeatedly to set the desired sleep time (90 ... 80 ... 70 ... ... 10mins ... off).
Display: Press DISPLAY to show the current time on the display. Mute: Press to mute / unmute sound output. AUX-IN: Connect another audio device, e.g. (portable) CD player, MP3 player, (portable) cassette player, etc. to this system via a cord with 3.5mm dia jack plugs (not supplied). Connect one end of this cord to the 3.5mm dia. Headphone jack on the external device and the other end to the aux-in jack (19) on the front of the unit.