August Smart Lock Installation Guide Welcome! This guide will get you up and running with your August Smart Lock. Installation generally takes less than 15 minutes. If you have any trouble, please call our customer support team at the number included in your Getting Started guide, or email support@august.com. Confirm Lock Compatibility Make sure your existing deadbolt is compatible with the August Smart Lock. Only standard single-cylinder deadbolts are supported.
1 August Smart Lock (AA batteries included) 1 Adhesive strip
Adapters 1 Mounting Plate What You'll Need Phillips Screwdriver 1. Prepare your existing deadbolt.
Affix the supplied adhesive strip over the keyhole, securing it to the exterior side of your door. This should hold the key hole in place when you remove the thumb-latch on the inside of the door. On some doors, such as those with glossy paint, the included tape may not be strong enough. In this case you should apply additional stronger tape to ensure that the key hole stays in place. Use caution. Some types of tape, such as duct tape, may damage the paint on certain types of doors.
2. Remove your existing thumb-latch. Position your thumb-latch so that you can unscrew the existing screws on your deadbolt. Remove the screws entirely from the deadbolt and keep them to assist in the next step. After removing the screws, be sure to unlock your deadbolt before removing the thumb-latch.
Your thumb-latch may include an additional back plate underneath it. If so, remove the back plate, and use the back plate and the longer screws for the next step. 3. Position and attach the mounting plate. The included mounting plate has two adjustable screw-holes that can be repositioned as needed.
Remove the screws from the thumb-latch and insert them into the front of the mounting plate (the back of the mounting plate is flat and includes 4 pre-attached rubber bumpers). Use the screws to install the mounting plate over the existing deadbolt tailpiece. Moderately tighten the screws by hand until the mounting plate is settled against the door. Do not over-tighten the screws - over-tightening can deform the mounting plate and interfere with the operation of the lock.
4. Select and attach the correct adapter. Select your adapter from the Compatibility Chart above.
(If your lock brand is not in the chart, slide each adapter onto the tailpiece to find the right one. The correct adapter will have the small nub pointing up.) Place the correct adapter onto the tail piece with the small nub pointing up. Tighten the screws until they are moderately tight. Do not over-tighten over-tightening can deform the mounting plate and interfere with the operation of the lock.
5. Attach the August Smart Lock. Insert the adapter into the back of the August Smart Lock, then position the August Smart Lock with the August name badge at the top. Pull out both side wing latches. Slide the August Smart Lock over the tailpiece and attach it to the mounting plate. Make sure the back of the lock is flush with the door.
To secure the August Smart Lock, clamp down both side wing latches to the mounting plate completely. If the latches are difficult to clamp down, go back to the last paragraph of step 4 and ensure that the screws have not been over-tightened. If the wing latches won't clamp down properly, you may need to adjust the tightness of the screws. 6. Use the August Home app to complete setup.
Download and install the August Home app. Select "Get Started" from the home screen, or, if already logged in to the app, select "Set Up a Lock" from the main menu.
Safety Environmental Risk of explosion and personal injury if batteries are replaced by incorrect type. Do not open, mutilate, or expose to conducting materials (metal), moisture, liquid, fire or heat above 54°C (130°F), incinerate, or immerse in water or liquid of any kind. Do not short circuit. Doing so may cause batteries to leak or explode, resulting in personal injury. Dispose of spent, leaking, or damaged batteries according to manufacturer instructions and local laws. Do not mix battery types.
Compliance FCC GENERAL STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
INDUSTRIE CANADA CONFORME Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Terms and Conditions
Limited Warranty Statement IMPORTANT: By using the August Smart Lock hardware (the “Device”) you are agreeing to be bound by the terms of this Limited Warranty set forth below.
www.august.com/support. August may attempt to troubleshoot a warranty-related problem prior to issuing a RMA number. August may ask for additional information upon request. Issued RMA numbers remain valid for thirty days from issuance.
facility authorized by August to service your August Device. This warranty does not cover consumable parts (such as batteries). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state (and jurisdiction to jurisdiction). 5. Disclaimer of Warranties. TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL, WRITTEN, STATUTORY, EXPRESS OR IMPLIED.
Specifications MODEL NAME: August Smart Lock DESCRIPTION: BLE Automatic Smart Lock MODEL NUMBER: ASL-3B STANDARDS: Bluetooth Specification v4.0 (Bluetooth Smart), 2.4GHz ISM band ANTENNA: Internal Single-band (Internal IFA) Transmitted The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by August Home, Inc. is under license. Other trademarks and trade names are those of their respective owners. Android is a trademark of Google Inc.