Installation Guide 1
Go to august.com/install to watch a video version of this installation guide.
Welcome! This guide will get you up and running with your August Smart Lock. Installation generally takes less than 15 minutes. If you have any trouble, please check our support section (august.com/support), contact our installer network (august.com/installers) or call 844-AUGUST1 (284-8781) for help.
Preparation Make sure your existing deadbolt is compatible with the August Smart Lock. Only standard deadbolts are supported. Use our compatibility assistant to doublecheck: august.com/compatibility Compatibility: YES Standard Deadbolt is mounted and operates independently of the door handle. Tools needed You will need a standard Phillips screwdriver.
Compatibility: NO Integrated Lock & Handle Handle and lock thumblatch are both mounted together on a metal plate Mortise Rim Cylinder An integrated door handle and deadbolt in a single metal unit Mounted on the inside, on top of the door and door jamb Alternately, we have a network of installers who can help with installation. august.
Package Contents 1 Adhesive Strip (Included Inside Envelope) 1 August Smart Lock (4 AA Batteries Pre-installed) 6 Installation Guide 4 Adhesive Rubber Bumpers (Included Inside Envelope)
3 Adapters 3 Mounting Plates 7
Installation Overview Before Installation Before: 1 3 2 1 2 3 4 5 Key Hole Deadbolt Tail Piece Thumb-latch Screws 4 After: 5 8 Installation Guide Key Hole Deadbolt Tail Piece Mounting Plate Screws Tail Piece Adapter August Smart Lock & Face Plate 1 2 3 4 5 6 7
After Installation 1 4 6 3 2 5 7 9
Step 1: Prepare existing deadbolt. Affix the supplied adhesive strip over the key hole, securing it to the exterior side of your door. This should hold the key hole in place when you remove the thumblatch on the inside of the door. On some doors, such as those with glossy paint, the included tape may not be strong enough. In this case you should apply additional stronger tape to ensure that the key hole stays in place. Use caution.
Step 2: Remove your existing thumb-latch. A Position your thumb-latch so that you can unscrew the existing screws on your deadbolt. Remove the screws entirely from the deadbolt and keep them to assist in the next step. After removing the screws, be sure to unlock your deadbolt before removing the thumb-latch. B Your thumb-latch may include an additional back plate underneath it. If so, remove the back plate. Use the back plate and the longer screws for the next step.
A B 13
Step 3: Select the correct mounting plate and adapter. If you know the brand of your deadbolt, please select the correct mounting plate and adapter from the Compatibility Chart on the next page, and then go to Step 4 (page 18). If not, go to Step 3a (page 16) to find the correct mounting plate and adapter. If your tailpiece is in a vertical position when the door is unlocked, you will need to remove the keyhole and rotate it so the tailpiece is in a horizontal position before you install.
Standard Deadbolt Compatibility Chart BRAND MOUNTING PLATE Baldwin - Estate/Images* Baldwin Reserve/Prestige Defiant Emtek Kwikset* Omnia** Schlage*** Weiser Weslock 1 3 2 3 3 1 2 2 1 ADAPTER * Baldwin and Kwikset Deadbolts installed before 1997 have unique installation requirements, please contact us at 844-AUGUST1 (284-8781) and we will walk you through installation. ** Compatible only with non-mortise, standard Omnia deadbolts. *** Commercial grade Schlage B560 deadbolts require supplemental screws.
Step 3a: Select the correct mounting plate. A Insert the existing screws in the thumb-latch to help you choose the correct mounting plate. If there was a back plate under your thumb-latch, insert the screws into this back plate instead of the thumb-latch. B Slide the mounting plates onto the screws one at a time until you find a mounting plate that allows the screws to fit straight through the holes. Having trouble selecting the right mounting plate? Try august.
A B Compatibility: YES B Compatibility: NO 17
Step 4: Position the mounting plate. A Remove the backing from the 4 rubber bumpers and place them on the back side of the mounting plate (the side that does not show a number). B Rotate the mounting plate so the 4 rubber bumpers are between the mounting plate and the door. Remove the screws from the thumb-latch and use them to install the mounting plate over the existing deadbolt tail piece. C Moderately tighten the screws until the mounting plate is settled against the door.
A Front: NO B Back: YES C 19
Step 5: Position adapter and align mounting plate. A Remove the tape from the key hole, and use your key to turn your deadbolt to the fully unlocked position. B If your lock was not in the Compatibility Chart, select the adapter that fits your tail piece. To do this, slide each adapter onto the tail piece. The correct adapter will have the small nub pointing up. C Place the correct adapter onto the tail piece with the small nub pointing up. Tighten the screws until they are moderately tight.
A B Front View Deadbolt Tail Piece Adapter Alignment C 21
Step 6: Attach the August Smart Lock. A Insert the adapter into the back of the August Smart Lock, then position the August Smart Lock with the August name badge at the top. B Pull out both side wing latches. Slide the August Smart Lock over tail piece and attach to mounting plate. Make sure the back of the lock is flush with the door. C To secure the August Smart Lock, clamp down both side wing latches to the mounting plate completely.
A B C 23
Step 7: Remove battery tab. A Press down on the August logo located at the bottom of the face plate. The top of the face plate will tilt outward. Grab the face plate and remove. B Holding batteries in place, remove the plastic battery isolation tab. Make sure that the battery is properly seated in its compartment. C Place the face plate back onto the August Smart Lock. Make sure the August logo is located along the bottom of the face plate.
A B C 25
Step 8: Install August App Download the App from august.com/app The app will help you create an account and set up your August Smart Lock. We suggest that you protect your phone with a passcode in case it is lost or stolen.
Questions? If you have any questions, call 844-AUGUST1 (284-8781) or visit august.com/support Lost your phone? Go to www.august.com to disable the August app running on your phone. ©2015 August Home Inc.
Terms and Conditons 1
Limited Warranty Statement 1. One (1) year Limited Hardware Warranty. Subject to the additional terms and conditions set forth below, August provides the following Limited Warranty: • Only to the person or entity that originally purchased the Device from August or from one of its authorized resellers or distributors; and • Only for Devices purchased and delivered to the end user within the United States, Canada, or Mexico. 2. Limited Warranty.
August Home Inc. Model: ASL-02 FCC: 2AB6UASL2 IC: 12163A-ASL2 REGULATORY COMPLIANCE INFORMATION The August Smart Lock (ASL-02) is subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules. NOTICE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
August Home Inc. Model: ASL-02 FCC: 2AB6UASL2 IC: 12163A-ASL2 Specifications Model Name: August ASL-02 Description: BLE Automatic Smart Lock Model Number: ASL-02 Standards: Bluetooth Specification v4.0 (BLE), 2.4GHz ISM band (2402MHz to 2480MHz), Channels: 40 x 2.0MHz channels Data rate & Modulation: 1Mbps, GFSK, 250 kHz deviation. Interface: Bluetooth Low Energy (BLE) LED: Lock/Unlock Speaker: Output, 1Watt Max. Antenna: Internal Single-band (Internal IFA) Transmitted Power: 0dBm Max.
