August Smart Lock Installation Guide
August Installation Guide
Welcome! This guide will get you up and running with your August Smart Lock. Installation generally takes less than 15 minutes. If you have any trouble, please check our support section (august.com/support), contact our installer network (august.com/installers) or call 844-AUGUST1 (284-8781) for help.
Preparation Make sure your existing deadbolt is compatible with the August Smart Lock. Only standard deadbolts are supported. Use our compatability assistant to double-check. august.com/compatibility TOOLS NEEDED You will need a standard phillips screwdriver. Alternately, we have an installer network available in major cities, who can help with installation. august.
Compatibility YES Standard Deadbolt is mounted and operates independently of the door handle NO NO NO Integrated Lock & Handle Mortise Rim Cylinder Handle and lock thumb-latch are both mounted together on a metal plate An integrated door handle and deadbolt in a single metal unit Mounted on the inside, on top of the door and door jamb 5
Package Contents 1 August Smart Lock (4 AA Batteries pre-installed) 6 August Installation Guide 1 Adhesive Strip (Inside Envelope)
3 Adapters 3 Mounting Plates 7
Installation Overview Before Installation 1 3 4 5 1 2 3 4 5 8 Key Hole Deadbolt Tail Piece Thumb-latch Screws August Installation Guide 2
1 After Installation 4 3 2 5 6 7 1 2 3 4 5 6 7 Key Hole Deadbolt Tail Piece Mounting Plate Screws Tail Piece Adapter August Smart Lock & Faceplate 9
Step 1: Prepare existing deadbolt. Affix the supplied adhesive strip over the key hole, securing it to the exterior side of your door. This should hold the keyhole in place when you remove the thumb-latch on the inside of the door.
Step 2: Remove your existing thumb-latch. A Position your thumb-latch so that you can unscrew the existing screws on your deadbolt. Remove the screws entirely from the deadbolt and keep them to assist in the next step. B Your thumb-latch may include an additional back plate underneath it. If so, remove the back plate. Use the back plate and the longer screws for the next step.
A B 13
Step 3: Select the correct mounting plate. If you know the brand of your deadbolt, please select the correct mounting plate and adapter from the Compatibility Chart and go to Step 4 (page 18). If not, go to Step 3a (page 16) to find the correct mounting plate and adapter.
Standard Deadbolt Compatibility Chart BRAND MOUNTING PLATE Baldwin - Estate/Images* Baldwin Reserve/Prestige Defiant Emtek Kwikset* Omnia** Schlage*** Weiser Weslock 1 3 2 3 3 1 2 2 1 ADAPTER Baldwin and Kwikset Deadbolts installed before 1997 have unique installation requirements, please contact us at 844-AUGUST1 (284-8781) and we will walk you Compatible only with non-mortise, standard Omnia deadbolts. through installation. Commercial grade Schlage B560 deadbolts require supplemental screws.
Step 3a: Select the correct mounting plate. A Insert the existing screws in the thumb-latch to help you choose the correct mounting plate. If there was a back plate under your thumb-latch, insert the screws into this back plate instead of the thumb-latch. B Slide the mounting plates onto the screws one at a time until you find a mounting plate that allows the screws to fit straight through the holes.
A B 1. 2. COMPATIBLE NOT COMPATIBLE Having trouble selecting the right mounting plate? Try august.
Step 4: Position the mounting plate. A Remove the screws from the thumb-latch and use them to install the mounting plate over the existing deadbolt tail piece. B 18 Do not fully tighten the screws.
A B 19
Step 5: Position adapter and align mounting plate. A Remove the tape from the key hole, and use your key to turn your deadbolt to the fully unlocked position. B If your lock was not in the Compatibility Chart, select the adapter that matches your tail piece. To do this, slide each adapter onto the tail piece. The correct adapter will have the small nub pointing up. C Place the correct adapter onto the tail piece with the small nub pointing up, and tighten the two screws. (Do not over-tighten.
A B Front View Deadbolt Tail Piece Adapter Alignment C 21
Step 6: Attach the August Smart Lock. Position the August Smart Lock with the curved notch at the top. A Pull out both side wing latches. Slide August Smart Lock over adapter and tail piece and attach to mounting plate. Make sure the back of the lock is flush with the door. B To secure the August Smart Lock, clamp down both side wing latches to the mounting plate completely and remove the clear tape from the curved notch.
A B 23
Step 7: Remove battery tabs. A Press down on the face place and rotate it counterclockwise to open the battery compartment. B Remove the two plastic tabs from the battery contacts. Make sure batteries are properly seated in the battery compartment. C Align faceplate hooks with the August Smart Lock. The faceplate will lock into place with the logo at the bottom.
A B C 25
Step 8: Install August App Download the app from august.com/app The App will then bring you through the necessary profiling and calibration processes.
Questions? If you have any questions or difficulty, visit august.com/support, call 844-AUGUST1 284-8781 or email questions to support@august.com 1006-0000-A Rev5 ©2014 August Home Inc.
Terms and Conditons 1
Limited Warranty Statement 1. One (1) year Limited Hardware Warranty. Subject to the additional terms and conditions set forth below, August provides the following Limited Warranty: • Only to the person or entity that originally purchased the Device from August or from one of its authorized resellers or distributors; and • Only for Devices purchased and delivered to the end user within the United States, Canada, or Mexico. 2. Limited Warranty.
August Home Inc. Model: ASL-01 FCC: 2AB6UASL01 IC: 12163A-ASL01 REGULATORY COMPLIANCE INFORMATION The August Smart Lock (ASL-01) is subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules. NOTICE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
August Home Inc. Model: ASL-01 FCC: 2AB6UASL01 IC: 12163A-ASL01 Specifications Model Name: August ASL-01 Description: BLE Automatic Smart Lock Model Number: ASL-01 Standards: Bluetooth Specification v4.0 (BLE), 2.4GHz ISM band (2402MHz to 2480MHz), Channels: 40 x 2.0MHz channels Data rate & Modulation: 1Mbps, GFSK, 250 kHz deviation. Interface: Bluetooth Low Energy (BLE) LED: Lock/Unlock Speaker: Output, 1Watt Max. Antenna: Internal Single-band (Internal IFA) Transmitted Power: 0dBm Max.