Owner/Installation Manual MMD100 10" DROP DOWN LCD MONITOR & DVD PLAYER 1
Important Notices Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants.
NOTE: This product incorporates copyright protection technology that is protected by method claims of certain patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation , and is intended for home and other limited viewing uses only, unless authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
A. Introduction Thank you for selecting the MMD100. The main features include a 10" Wide Screen (16:9 Aspect Ratio) Liquid Crystal Display (LCD) monitor and a built-in DVD player. The unit applies the latest state of the art electronics. The unit is constructed to provide years of reliable, trouble-free service. Please read the entire instruction manual supplied with this product prior to operation. The documentation will assist you in installing the system properly to obtain the best equipment performance.
. Disc Do not use irregularly shaped discs such as heart or star-shaped discs as they may cause the unit to malfunction. Do not stick paper, tape or glue on the disc. Do not expose the disc to direct sunlight or heat sources such as hot air ducts. Do not touch the surface of disc. Handle the disc by its edge. Clean the disc by wiping the disc from the center out with a cleaning cloth. Remove the disc from the unit and store it in its case after playing.
D. Installation and Powering TOOLS REQUIRED: #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark trim ring if used) Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to vehicle.
5) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagrams on page 10 of this manual as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room.
Note: The MMD100 video system is only intended for an overhead, drop down installation. It is not intended for seat back or any other type of mounting. The hinging mechanism is designed for horizontal, drop down use only. VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off). Generally, this wire can be found at the ignition switch or fuse-box.
MOUNTING THE MMD100 Trim Ring Video Unit M4 8mm M4¡Á8mm Figure 1 Trim Ring Installation The Trim Ring Installation is accomplished using the four (4) 2.6X10mm screws supplied. Please refer to the Figure 2.
A A A A Figure 2 1. Place the MMD100 on a soft surface with the rubber gasket facing up. Use care to avoid scratching the unit’s exterior surface. 2. Take off the rubber ring. 3. Place the trim ring on the unit and note the location of the four mounting screws. 4. Attach the trim ring to the unit using the longer four (4) 2.6 X 10mm screws supplied. 5. Attach the four (4) post extensions to the bracket (Figure 3).
Figure 3 6. Attach the four (4) rubber spacers on the post extensions (Figure 4). Figure 4 7. Refer to the Owner/Install Manual for the MMD100 to complete the installation.
MMD100 Antenna Y Figure 5 1) Make the connections to the vehicle with the 5 pin wiring harness. 2) Connect the 5 pin harness to the mating connector on the Video Monitor. 3) Connect power harness to vehicle's electrical system by tapping into an accessory hot line. 4) Verify all functions of the system before final mounting of the finished assembly. NOTE: A VCP or other A/V Component can be connected to the video monitor system using an RCA A/V cable.
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light.
Positive Switched Dome lighting To constant +12vdc Red / black - Lamp on Black / red - Lamp common Violet / brown - Lamp Auto To 3 pin connector on Monitor Factory Dome light circuit To constant +12vdc Factory Door ajar switch or Body Control computer Figure 6 Negative Switched Dome lighting To 3 pin connector Red / black - Lamp on Black / red - Lamp common Violet / brown - Lamp Auto To constant Factory Dome light circuit To constant Factory Door ajar switch or Body Figure 7 14
E. Controls, Indicators, and Connectors 1.
2.
G.
H. Setup Press ‘SETUP’ to display the Main screen of the Setup Menu. Press ‘SETUP’ again to exit the Setup Menu and the unit will resume it’s last playback mode. Main Setup Menu Screen 1) Press “SETUP”, the ‘General Setup Page’ will be displayed. a).Select ‘TV Display’ using the S/T button, and then press XX to enter the submenu. Select the TV display mode on the screen using S/T, and press ENTER to confirm the setting. Press WW to return.
b).Select ‘Angle Mark’ using the S/T button, and then press the XX button to enter the submenu. Choose Angle Mark on or off using the S/T button and then press ENTER to confirm the setting. Press the WW button to return. Angle Mark Screen Display * On: The screen will show the angle mark icon. (*If an angle option is available). * Off: The screen will not display the Angle Mark NOTE: Not all discs contain above features. The above features are disc dependent. d).
e). Select ‘Last Memory’ using the S/T button and then press the XX button to enter the submenu. Choose Last Memory on or off using the S/T button and then press ENTER to confirm the setting. Press the WW button to return. Last Memory Screen Display *On: *Off: The unit will return to the last position on the disc when power is cycled, but not if disc is ejected. The unit will not return to the last position on the disc.
2) Select “Video Quality Setup”by using the WW/XX button, press ENTER to enter the video quality setup page. Video Quality Setup Screen Display a) Select ‘Brightness’ by using the S/T button, then press ENTER. To change the Brightness, press the WW/XX button. To exit ‘Brightness’ setting, press ENTER again to return the main Menu.
b).Select ‘Contrast’ by using the S/T button, then press ENTER. To adjust the Contrast, press the WW/XX button. Contrast Screen Display To exit ‘Contrast’ Setting, press ENTER again to return the main Menu. c).Select ‘Saturation’ by using the S/T button, then press ENTER. To adjust the Saturation, by press the WW/XX button. Saturation (Color) Screen Display To exit ‘Saturation’ setting, press ENTER again to return to the main Menu. d).Select ‘Hue’ by using the S/T button, then press ENTER.
3).Select “Password” using the WW/XX button, then press ENTER and press the XX button to enter the submenu. Password Setup Page Screen Display Press ENTER to enter the Password Change Page. Input the Old Password or the Default Password (Default 3308), followed by entering the New Password, and the Confirmed New Password. Press ENTER to accept the change. Password Change Page Screen Display NOTE: The Default Password is 3308.
4).With no disc inside the player select ‘Preference Page’ using the WW/XX buttons, then press ENTER to enter the Preference Page. a). Select ‘Audio’ using the S/T button, then press XX to enter the submenu. Select the audio language you desire using the S/T button, then press ENTER to confirm the setting. Press WW to return. Preference Audio Language b). Select ‘Subtitle’ using the S/T button, then press XX to enter the submenu.
c). Select ‘Disc Menu’ using the S/T button, then press XX to enter the submenu. Select the Disc Menu Language you desire using the S/T button, then press ENTER to confirm the setting. Press WW to return. Preference Menu Language d). Select ‘Parental’ using the S/T button, then press XX to enter the submenu.
e). Select ‘Default’ using the S/T button, then press XX to enter the submenu. Press ENTER to return all settings to the factory-set mode. NOTE: The parental setting and password are not affected by the default reset function and remain at their current values.
I. Menu A DVD is divided into sections called titles and chapters. When you play a DVD, a root menu of the disc will appear on the screen of your TV or Monitor. The contents of the menu vary from disc to disc. Press MENU during playback to display the menu. Some DVDs only allow you to select disc playback options using the DVD root menu. J. Display 1. PLAYING TIME AND REMAINING TIME a.
2. ANGLE During playback of a disc, press ‘ANGLE’ to display the available angles for discs containing multi-angles*, with the current angle number (1) and the total number of angles (2) displaying. Press ‘ANGLE’ to select another angle, then press again to exit and return to the normal viewing angle. The angle information will disappear automatically if the ‘ANGLE’ button is not pressed again within 3 seconds. *NOTE: Not all discs contain this feature. Angle Screen Display 3.
4. AUDIO During playback press ‘AUDIO’ to select the audio language you desire*, with the current Audio Channel Number (1) and the total number of Audio Channels (2) displayed. Press AUDIO again to select another audio language. The audio display will disappear automatically if the ‘AUDIO’ button is not pressed within for 3 seconds. Audio 1 / 2 : Ac3 5 . 1Ch Audio Language Screen Display * Some DVDs only allow access to this function through the DVD menu. 5.
6. A-B REPEAT a. During playback press ‘A-B’ to set the Starting Point A. A-B Repeat Starting Point Screen Display b. Press ‘A-B’ a second time to set the Ending Point B. The player will repeatedly play the part between Point A and Point B. A-B Repeat Ending Point Screen Display c. Press ‘A-B’ a third time to cancel A-B repeat and resume normal playback.
7. REPEAT During playback each time REPEAT is pressed, the following modes will become available: Chapter Chapter: Repeat the current chapter Title: Repeat the current title All: Repeat all chapters and titles Off: Resume normal playback Off Title All DVD Repeat Mode The ‘Chapter’ repeat display is shown below for example: Chapter Repeat Screen Display K. Playing Audio CDS When playing an audio CD press the DISPLAY button repeatedly on the remote to view time information.
Total Elapsed: The current track playing and the total time that the CD has been playing. Total Remain: The current track playing and the amount of time remaining on the CD. Display Off: The CD time Information will not be displayed. Take ‘Single Elapsed’ display as a example: Single Elapsed Screen Display USING THE REPEAT FEATURE The default mode for the Repeat feature is OFF. Pressing REPEAT consecutively changes the repeat options: • Track- repeats the track that is playing.
L. Playing MP3 Discs MP3 is a format for storing digital audio. An audio CD-quality song is compressed into the MP3 format with very little loss of audio quality while taking up much less disc space. CD-R /RW discs that have been encoded in MP3 format are compatible with this system. MP3 MENU Screen Display When an MP3 disc is inserted into the unit, the menu screen appears automatically.
4. Use the ( NEXT ) button to move to the next song. Press the (PREVIOUS) button to move to the beginning of the previous song. USING THE REPEAT FEATURE The default mode for the Repeat feature is OFF. Pressing REPEAT consecutively changes the repeat options: • Repeat One (repeat playback of a song) • Repeat Folder (repeat playback of a specific folder) • Repeat Off (normal playback) As you toggle through the options, the repeat mode changes. The selected repeat mode loops repeatedly until you turn it off.
M. Playing a Video Game (Refer to Figures 10 and 11.) Change the source by pressing the DVD/AUX button on the remote. The AV1 input is the RCA connectors located on the top of the unit. The AV2* input jack is located on the left side of the unit. * Figure 10 Figure 11 Connect the A/V output from your game system to the RCA inputs (AV1) or the 1/8 (AV2)* input. Adjust the volume and picture for individual preference. N. Wired Headphones and Wireless headphones (Refer to Figure 11.) 1.
O.Wireless FM Modulator The MMD100 is equipped with built-in wireless FM Modulator*, that allows you to listen to the MMD100 audio signal by tuning your vehicle’s radio to the selected frequency (88.1, 88.3, 88.5, 88.7 or 88.9 MHz). First, Press the FM button on the player, The “FM ** MHz” will appear on the screen. Then use the FM button on the remote control to select the frequency you desired. Select the same frequency on the vehicle’s radio.
P. Specification Disc format: DVD/CD/MP3/JPEG Color system: NTSC Screen size: 10” Frequency response: 20 Hz to 20 kHz Video output: 1 Vp-p/75 Ohm, unbalanced Audio output: 1.4Vrms/10kOhm Audio S/N: Better than 60 dB Dynamic range : Better than 85 dB Laser: Semiconductor Laser, Wave Length: 650 nm/790 nm Power source: DC 12V Power consumption: 18 W Operating temperature: 5~35°C Storage temperature: -20~60°C (4~140°F) Weight:1.47Kg Dimensions (W x H x D): 276.0 x 235.0 x 47.5 mm(10.9” x 9.3” x 1.9”) Q.
12 MONTH LIMITED WARRANTY Applies to Movies To Go Mobile Video Products AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor.