Installation Manual

ManualsBrandsAudiovox ManualsDVD PlayerAVXMTG13UA

13.3-Inch LED Backlit LCD Roof-Mount DVD Player

With DVD/CD/MP3 SYSTEM

AVXMTG13UA

INSTALLATION

GUIDE

Summary of content (20 pages)

PAGE 1
3.
PAGE 2
PAGE 3
TABLE OF CONTENTS Important Notices ��2 IR Transmit and Receive Modes (M1 or M2) ��
PAGE 4
IMPORTANT NOTICES WARNINGS Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes anchor points in A, B, C or D pillars of the vehicle.
PAGE 5
IR TRANSMIT AND RECEIVE MODES (M1 OR M2) The AVXMTG13UA has an option that allows the user to select from two IR transmit and receive modes (M1 or M2). This feature can be used when two AVXMTG13UA units are installed in the same vehicle or if the vehicle has an RSA (Rear Seat Audio) that uses “A” channel headphones. When in the M1 mode the unit will transmit audio on the A channel. When in the M2 mode the unit will transmit audio on the B channel.
PAGE 6
MATERIALS INCLUDED IN THIS PACKAGE Hardware Package a 3 2 1 5 6 7 9 10 11 b c d 4 8 e 1. 2. 3. 4. 13.3” LCD Overhead Monitor with DVD player (1 pc) 12 Pin Power Harness (P/N 112-4216) (1 pc) 2 Pin Power / Wire Harness with Choke(P/N 112-4129)(1 pc) Hardware Package (P/N 150-1830) (1 pkg) a.)M2.6 x 6mm Self-Tapping Screws (P/N 100-2568) (10 pcs) b.)M4 x 15mm Self-Drilling Screws (P/N 100-2567) (4 pcs) c.)M5 x 15mm Phillips Screws (P/N 100-2604) (4 pcs) d.
PAGE 7
REMOVING AND INSTALLING SNAP-ON COVERS AND SHROUD Preparation Place the unit on a soft surface to avoid damaging the plastic. Materials Required 1. 1 2. 2 13.3” Overhead LCD Monitor with DVD Player 4. 4 3. 3 Snap On-Shroud Snap On-Cover Pry Tool Disconnecting the Screen Cover 1 2 “A” 3 “B” “C” “C” 1. Open the LCD screen. 2. Insert the supplied pry tool between the LCD screen and snap on screen cover at locations “A”, “B”, and “C” and gently pry the cover away from the screen.
PAGE 8
Installing the Screen Cover “D” “D” “D” “D” 1. Open the LCD screen. 2. Hook the two tabs “D” at the bottom edge of the screen cover into the notches on the bottom edge of the LCD screen. 3. Snap the opposite side of the screen cover over the hinges. Disconnecting the Shroud 1 2 “E” (Fasteners) 1. Open the LCD screen. 2. Insert the supplied pry tool between the unit and shroud at fastener locations “E” and gently pry the shroud away from the unit.
PAGE 9
Installing the Shroud 1 2 “F” “F” 1. Open the LCD screen. 2. Slide the shroud over the unit. The shroud will snap into place at locations “F”.
PAGE 10
INSTALLING THE TRIM RING NOTE: The trim rings supplied with this unit are not designed to be trimmed. The trim ring is attached to the video monitor using the perimeter screw bosses. It is important that the screws used in this installation are not over tightened, and that the video monitor and trim ring are mounted in such a way that the assembly does not distort (or bend) when the mounting screws are tightened. NOTE: Some applications will not require a trim ring to be installed. 1.
PAGE 11
GENERAL VEHICLE INSTALLATION APPROACH 1. 2. 3. 4. Decide upon the system configuration and options that will be installed. Review all manuals to become familiar with electrical requirements and hookups. Decide upon the mounting locations of all components and the method of mounting. Prep the vehicle. Remove any interior trim necessary to gain access to vehicle's wiring, as well as all areas where interconnecting wire harnesses will be located.
PAGE 12
VEHICLE PREPARATION 1. Locate an accessory +12v power source with a good ground. These wires can be found at the ignition switch or fuse-box. Power Source • +12v when the key is in the ACC. and run positions. • 0v when the key is OFF. 2. The mounting method and location will vary from vehicle to vehicle, the only focus of this manual is the installation of the AVXMTG13UA and related console accessories. 3.
PAGE 13
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle’s wiring. There are two common types of dome light circuits used, positive switched systems or negative switched systems. Positive switched systems supply voltage to the interior lights to turn ON; negative switched systems apply ground to illuminate the bulbs.
PAGE 14
CONNECTING THE DOME LIGHTS Positive Switched Dome Lighting To 3 pin connector on Monitor Red/Black-Lamp ON Black/Red-Lamp Common Purple/Brown-Lamp Auto Negative Switched Dome Lighting To constant +12 VDC To 3 pin connector Red/Black-Lamp on Black/Red-Lamp common Purple/Brown-Lamp Auto To constant +12 VDC Fused Fused Factory Dome Light Circuit To constant +12 VDC To constant +12 VDC Factory Door Ajar Switch or Body Control Computer Factory Door Ajar Switch or Body Control Computer 12
PAGE 15
INSTALLING THE MOUNTING BRACKET Installing the Mounting Bracket 1. Once all the pre-wiring is complete, locate: • Mounting Bracket • (4) M4 x 15mm Self-Drilling Screws 2. Carefully align the Mounting Bracket in the location it is to be installed (make sure there is nothing between the Mounting Bracket and Roof Cross-Member). 3. While holding the Mounting Bracket in place, install the (4) M4 x 15mm Self-Drilling Screws.
PAGE 16
WIRING THE AVXMTG13UA VIDEO SYSTEM 1. 2. 3. 4. Make the connections to the vehicle for the 12 pin wiring harness (P/N 112-4126). Connect the 2 Pin Power Harness (P/N 112-4129) to vehicle’s electrical system by tapping into an accessory hot line and a good ground. To connect an external AV source, utilize the 3.5mm to RCA jack pigtail harness. To utilize the AV output feature, connect the RCA output connectors on the 12-pin harness to the input of an optional external monitor. 5.
PAGE 17
INSTALLING THE AVXMTG13UA VIDEO SYSTEM Installing the AVXMTG13UA System 1. Make all electrical connections. 2. Attach the AVXMTG13UA unit to the mounting bracket using four M5 screws. Roof Front of Vehicle Headliner Mounting Bracket Mounting Bracket Video Unit AVXMTG13UA 4 x M5 Screws MountingHoles CAUTION: The 15mm, 25mm and 40mm screws (4 each) in the hardware kit are provided to facilitate installation.
PAGE 18
TROUBLESHOOTING SYMPTOM: No power at Video Monitor REMEDY: Power but no video or sound Verify that the correct source is selected (i.e.: 1, 2, 3 or 4). Verify that the source is on and playing a known good media (such as a videotape). Verify the connections at both ends of the source component harness. Verify +12 VDC on the Red wire at 2 Pin Power Harness behind the video monitor.
PAGE 19
PAGE 20
www.audiovoxproducts.com 2013 AUDIOVOX,150 AUDIOVOX,150Marcus MarcusBlvd. Blvd.