User Manual

ManualsBrandsAudiosource ManualsAmplifiers2-Channel Analog Power Amp (150W per Channel), Black

AMP310VS

Stereo Power Amplifier

FEATURES:

MAIN / INTERRUPT priority input switching

MAIN auxiliary output

Speaker A/B switching

Signal sensing “Power On” and Trigger mode

Rear mounted treble and bass controls

High level input

Front panel balance and volume trim controls

Independent rear left / right master level controls

Front panel diagnostic LEDs

Triple-Darlington Power Amplifier Stages

Dual-differential error amplifiers Rack-mountable

SPECIFICATIONS

Stereo (8 ohm):

150W per channel, <0.2% THD+N

Stereo (4 ohm):

225W per channel, <0.2% THD+N

Bridged Mono (8 ohm):

450W, 1kHz, <0.2% THD+N

Frequency Response:

10Hz ~ 50kHz, +0dB/ -3dB

Signal to Noise Ratio:

100dB below 150W output into 8 ohms

Channel Separation:

70dB

Input Sensitivity:

Variable, 350mV to 2.8V for rated

power into 8 ohms

Bass/Treble Control:

+/- 12dB @ 100Hz and 10kHz

AC Power Consumption:

1200W maximum

Net Weight:

33.1lbs / 15.0kgs

Gross Weight:

39lbs / 18.0kgs

Congratulations on your purchase of the AudioSource® AMP310VS.

Please take a few moments to read this entire manual, and be sure to

retain this document for future reference. Please read and observe all

safety instructions detailed on page 2.

NOTE: If any part of this product is damaged or missing, please call your

dealer or AudioSource® directly at 1.877.715.5439 or 503.914.4688.

Please read your warranty and retain your receipt and original carton for

possible future use.

For more information about AudioSource® electronics, speakers and

accessories please visit www.audiosource.net

16.5”(419mm)

OWNER’S MANUAL

AMP310VS

Summary of content (6 pages)

PAGE 1
AMP310VS OWNER’S MANUAL Congratulations on your purchase of the AudioSource® AMP310VS. Please take a few moments to read this entire manual, and be sure to retain this document for future reference. Please read and observe all safety instructions detailed on page 2.
PAGE 2
AudioSource® 13970 SW 72nd Ave Portland, OR 97223 503.914.4688 www.audiosource.
PAGE 3
AMP310VS OWNER’S MANUAL The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products’ enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
PAGE 4
1. Read these instructions. 13. Unplug the apparatus during lightning storms or when unused for long periods of time. 2. Keep these instructions. 14. Refer all servicing to qualified personnel. Servicing is required 3. Heed all warnings. when the apparatus has been damaged in any way, such as power 4. Follow all instructions. supply cord or plug is damaged, liquid has been spilled or objects have 5. Do not use this apparatus near water.
PAGE 5
AMP310VS 1. Power Switch Switches the AMP310VS on or off. 2. Clip LEDs Blinks red during signal clipping. Shows solid red during protect mode. Check speaker wires for shorts or extreme low impedance (< 4 ohms). REAR PANEL CONTROLS 6. Interupting Line Input This is the secondary input, use MAIN IN for your main input. INTERRUPTING INPUT can be used if a second source is desired and takes over when signal is present and has at least a 5mV level.
PAGE 6
NOTE: Use Class 2 wiring for speaker connections. To wire the output connector: 1. Strip the insulation off each speaker wire to expose 3/8" (10 mm) of bare conductor. 2. Unscrew the output terminal binding post several twists, insert each wire into the correct terminal. 3. Tighten binding post by twisting clock-wise until it is firmly clamping the speaker wire.