Full Product Manual

ManualsBrandsAudioSource ManualsElectrical2-Channel Analog Power Amplifier

AMP210VS

OWNER’S MANUAL

AMP210VS

AudioSource®

13970 SW 72nd Ave

Portland, OR 97223

503.914.4688

www.audiosource.net

AMP210VS Owner’s Manual 72015

Congratulations on your purchase of the AudioSource® AMP210VS.

Please take a few moments to read this entire manual, and be sure to

retain this document for future reference. Please read and observe all

safety instructions detailed on page 2.

NOTE: If any part of this product is damaged or missing, please call your

dealer or AudioSource® directly at 1.877.715.5439 or 503.914.4688.

Please read your warranty and retain your receipt and original carton

for possible future use.

For more information about AudioSource® electronics, speakers and

accessories please visit www.audiosource.net

FEATURES:

SPECIFICATIONS

Stereo (8 ohm): 100W per channel, <0.2% THD+N

Stereo (4 ohm): 125W per channel, <0.2% THD+N

Bridged Mono (8 ohm): 250W, 1kHz, <0.2% THD+N

Frequency Response: 10Hz ~ 50kHz, +0dB/ -3dB

Signal to Noise Ratio: 100dB below 100W output into 8 ohms

Channel Separation: 70dB @ 1kHz, referred to 100W output

into 8 ohms

Input Sensitivity: Variable, 350mV to 2.8V for rated power

into 8 ohms

AC Power Consumption: 700W maximum

Net Weight: 24lbs / 10.9kgs

Gross Weight: 30lbs / 13.6kgs

Stereo Power Amplifier

AMP210VS

Bass/Treble Control: +/- 12dB @ 100Hz and 10kHz

3.8”

(96.5mm)

16.5” (419mm)

MAIN / INTERRUPT priority input switching

MAIN auxiliary output

Speaker A/B switching

Signal sensing “Power On” and Trigger mode

Rear mounted treble and bass controls

High level input

Front panel balance and volume trim controls

Independent rear left / right master level controls

Front panel diagnostic LEDs

Triple-Darlington Power Amplifier Stages

Dual-differential error amplifiers

Rack-mountable

13.75”

(349mm)

Summary of content (4 pages)

PAGE 1
AMP210VS OWNER’S MANUAL AMP210VS Stereo Power Amplifier FEATURES: MAIN / INTERRUPT priority input switching MAIN auxiliary output Speaker A/B switching Signal sensing “Power On” and Trigger mode Rear mounted treble and bass controls High level input Front panel balance and volume trim controls Independent rear left / right master level controls Front panel diagnostic LEDs Triple-Darlington Power Amplifier Stages Dual-differential error amplifiers Rack-mountable Congratulations on your purchase of the A
PAGE 2
AMP210VS OWNER’S MANUAL CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL! EXPLANATION OF SAFETY SYMBOLS The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
PAGE 3
AMP210VS OWNER’S MANUAL 2 1 3 4 Figure 1. Front Panel 3. Speaker Selector Selects speaker zone A or B. For A + B zones push both buttons in. 4. Balance Fades speaker output between the Right and Left Channels 5. Volume Trims ampliﬁer volume from -12dB to +6dB referenced to the rear panel Level controls. FRONT PANEL CONTROLS 1. Power Switch Switches the AMP210VS on or off. 2. Clip LEDs Blinks red during signal clipping. Shows solid red during protect mode.
PAGE 4
AMP210VS OWNER’S MANUAL 17. Mains Power Inlet & Fuse Holder Accepts IEC type line cord. Afuse located in the integrated holder provides safety protection from fault conditions: replace fuse with one of same type and rating only. 18. Mains Voltage Selector Voltage selection switch is preset to 115V (USA). For use in areas which require 230V contact your dealer. Fuse must be of type and rating marked on amplifier for use at local mains voltage.