DJAP Series HYBRID PORTABLE PA SYSTEM User’s Manual DJAP-612PB DJAP-612PB DJAP-615P
Safety Related Symbols This symbol, wherever used, alerts you to the presence of uninsulated and dangerous voltages within the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death. This symbol, wherever used, alerts you to important operating and maintenance instructions. 'sinstructions.To avoid the risk of electric shock and damage, do notsubject this product to any liquid/rain or moisture.Do not use this product when in close proximity to water.
Table of Contents INTRODUCTION ----------------------------------------------------------------------------------------------------------------------------------------------------------------------4 FEATURES ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 4 CONTROL ELEMENTS ----------------------------------------------------------------------------------------------------------------
1. Introduction Thank you for purchasing the DJAP 2-way vented powered speaker system. This unique system was designed to be an all-in one portable solution with built-in High Power amplifier, 4 channels mixer with 3-band EQ and 24-bit DSP effects. The DJAP combines practicality with top design concepts achieved over many years of manufacturing quality products. Please read this manual carefully so you can take advantages of all the features of the DJAP. 2.
effect device. QUALIZER The UPA features a 3-band equalizer which allows you to adjust the high, mid and low frequencies separately on each mono channel. 5. HIGH This is the treble control. You can use it to get rid of high frequency noises or to boost the sound of cymbals or the high harmonics of the human voice. The gain range goes from -15 dB to +15dB with a center frequency of 12kHz. 6. MID This is the mid range control.
sound. The EQ function will be activated automatically as soon as you operate your DJAP . 15. MAIN MIX LEVEL Control This control is used to adjust the overall volume of the main mix output. The adjustable range goes from - to +10dB. 16. OUTPUT LEVEL LED The 4-segment LED meter is used to indicate the output level. 17. POWER LED This LED lights up when the unit is powered on. 18. MAIN OUT Jack This jack is used to output the main mix signal to an external unit. 19.
3.3.USB-MP3 player section 29. USB PORT For connecting with USB memory. 30. SD CARD PORT For connecting with SD CARD memory. 31. PRE In pause state, press this button it will go to the previous song and keep in pause state. In play+ state, press this button it will go to the previous song and start playing. 32. NEXT In pause state, press this button it will go to the next song and keep in pause state. In play state, press this button it will go to the next song and start playing. 33.
42. BATTERY These LEDs are used to indicate the power of the battery. 43. EXT. DC 12V When the AC and battery are out of power, you can use the EXT. DC 12V supply to the unit. 44. POWER AMP. Switch Turn the Power AMP switch on "OFF" position, the EXT. DC output will be cut off, and the battery will store the power; this switch on "ON" position, the EXT. DC supply will work on normal condition. 47 47 46 45 43 41 44 46 48 42 40 45.
50. AF-LEVEL Indicator These LEDs indicate the incoming status of the audio signal. The four green LEDs light up indicate normal condition. When the audio signal from microphone approaches clipping level the red LED indicator lights up, If no LED lights up, there is little or even no signal being received. 51. MIC. ON & Diversity Signal Indicator These indicators light up during standby. When microphone signal is received, the A or B signal indicator lights up to indicate the reception of microphone. 52.
4. Installation Tips 1- Speakers should be placed in a position that allows for unobstructe sound projection. In many instances is beneficial for speakers to be elevated on tripod stands to achieve maximum dispersion and reach. 2- Use professional advice or service when hanging and installing speakers. Please take precautions to secure them to prevent them from falling and hurting someone. Care should be taken as to not damage the cabinet or its components. Please comply with all pertinent Regulations.
MATCHING WITH PASSIVE SPEAKER & SUBWOOFER In this example, it connects a sub-woofer, and the woofer of this two full-range act like midwoofer. This is very popular combination especially in small size clubs where there is no need for two sub-woofers. Speaker Cable OF F PASSIVE SPEAKER From Monitor Out 6. Installation and Connection 6.1 Set-up Ok, you have reached this point and you are now in the position to successfully operate your DJAP.
For1/4"PhoneJack ForXLRConnector -In line Connection For these applications, the DJAP provides 1/4" TRS connectors, XLR connectors and RCA connectors to interface with most professional audio devices easily. Follow the configuration examples below for your particular connection. Balanced Unbalanced -In line Connection If you are connecting to a mixing console's main inserts, you may have single TRS jack for Send & Return. In this case, use an insert "Y" cable that configured like the example below.
1 DJAP-612PB DJAP-615P 1 2 3 LEVEL 2 3 1 2 MP3 SW 3 1 RF SW Wireless MIC TO MAIN 7-BAND GEQ MP3 Wireless MIC MON LEVEL MAIN LEVEL FOOT SW AMP LIMITER DISPLAY 1 2 3 1 2 3 1 2 3 1+ 1- REC OUT SP OUT OUT 2+ 2- R L FX SEND MON OUT MAIN OUT 70~79 80~89 90~99 MINI D3.
9. TECHNICAL SPECIFICATIONS SPECIFICATIONS DJAP-612PB DJAP-615P bal Mic/Line channels in 4 4 Tape in 1 RCA in+1 Mini ST in 1 RCA in+1 Mini ST in Fx RTN in 1 1 Main out 1 1 Monitor out 1 1 Fx send 1 1 REC out 1 1 MIC TO MAIN/MON 50dB 50dB GAIN LINE TO MAIN/MON 30dB 30dB FREQUENCY RESPONSE(-1dB) 20Hz-20KHz 20Hz-20KHz MIC IN 2K 2K Impedance LINE IN 20K 20K TAPE IN 10K 10K MAIN/MON OUT 1.5K 1.5K ALL MAX OUT 22dBu 22dBu S/N >80dB >80dB THD <0.1% <0.1% 3 band(80/2.5K/12K) 3 band(80/2.
10. GUARANTEE AUDIOPIPE guarantees the normal operation of the product against any defect of manufacture and / or vice of material, by the term of 12 months, counted as of the date of purchase on the part of the user, committing itself to repair or to change, to its election, without position some, any piece or component that will fail in normal conditions of use within the mentioned period.
