Features • 5 Channel Amplifier with AccuBASS® Processing • Configurable as 3 or 5 channels • 4 x 100 W @ 4 Ohms + 1 x 300 W @ 4 Ohms • 4 x 200 W @ 2 Ohms + 1 x 500 W @ 2 Ohms • High Current Design • 6 RCA Line Inputs • 8 Summable Speaker-Level Inputs for OEM integration • MILCTM Level Matching Technology (Patent pending) • GTOTM Signal Sense (Great Turn On) • Independent 12 dB Linkwitz-Riley Crossovers • Optional ACR-1 Dash Remote • Non-GMO, Grade AA goodness LC-5.
LC-5.1300 Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as mufflers, silencers, exhaust pipes, or other apparatus (including amplifiers) that produce heat.
Connection Panel Features 1 2 3 4 5 1. Fuses 30A – Replace these fuses only with the exact same style and Ampere rating. Disconnect 12V power before changing or inspecting the fuses. 2. Power Input Terminal +12V – This screw terminal connects to the +12V battery binding post of the vehicle. Use quality insulated wire, 4 to 0 AWG. 3. Remote Power Input Terminal – This screw terminal connects to the 12V remote trigger output of some head units. When the head unit is turned on, then the LC-5.
LC-5.
9. Power LED – If you have connected your battery power, vehicle ground, and turn-on lead (or GTO signal sensing) correctly, then this light should be green to indicate the power is ON. 10. Protection LED – The amplifier has built-in diagnostic codes to tell you exactly what is going wrong should the amplifier detect a problem. See page 15 for a list of diagnostic codes. 11. GTO Signal Sense – In the ON position, the LC-5.
LC-5.1300 25. AccuBASS® Threshold – Selects the level at which the AccuBASS® will begin to work. AccuBASS® and ACR-1 Notes 26. AccuBASS® Level – Adjusts the level of the AccuBASS®. AccuBASS® 27. Crossover Frequency – Selects the LP crossover point to match your speakers and system. The channel 5 output will receive the frequency range below the frequency selected. 28. Gain Control – Adjusts the overall 5 output levels. 29.
Quick Start Here are a few general steps to get your LC-5.1300 amplifier up and running: 1. Undo the +12V and Ground connections to the car battery before making any connections to the amplifier. 2. Pick a mounting location that will provide access to the controls and connections, provide adequate ventilation, and also protect the amplifier from heat, moisture, and dirt. Make sure the ventilation slots on the sides are not blocked, and that the heatsink fins are not covered. 3. The LC-5.
LC-5.1300 Power Connections Head Unit Head Unit LC-5.1300 turns on using GTO on inputs 1 and 2 Remote terminal on LC-5.1300 now acts as a trigger out Remote Amplifier +12V Trigger +12V +12V Ground Ground In this example, the head unit has a +12V trigger output that is connected to the LC-5.1300’s remote input terminal. When the head unit is turned on, it will turn on the LC-5.1300 amplifier. Use 4 to 0 AWG insulated wire for the +12V and Ground connections.
0 Hz Enable Sum Stereo High Pass N/A Separate 90 Hz Stereo Low 90 Hz CCW ON System #1: Using speaker-level inputs + Front left/right Speaker-level output 90 Hz and above + Factory Radio Rear Speaker-level output Front Speaker-level output + Rear left/right Speaker-level output 90 Hz and above + ACR-1 Notes: The +12V Power and Ground connections are not shown (see page 8) Speaker outputs 1 and 2: Stereo, 90 Hz and above, plays inputs 1 and 2 Speaker outputs 3 and 4: Stereo, 90 Hz and abo
LC-5.1300 90 Hz Sum Enable 3.5 kHz Stereo Band Pass 90 Hz Sum Stereo 500-5 kHz 3.5 kHz CCW ON System #2: Tri-amping + Front L/R tweeters Speaker-level output 3.5 kHz and above + Factory Radio + Front Speaker-level output Front L/R Woofers Speaker-level output 90 Hz to 3.5 kHz + ACR-1 Notes: The +12V Power and Ground connections are not shown Speaker outputs 1 and 2: Stereo, 3.
90 Hz Sum Enable NA Stereo High Pass 90 Hz Sum Stereo Low 90Hz CCW ON System #3: Using optional ACX-BT1 Bluetooth receiver + Front left/right Speaker-level output 90 Hz and above + + ACX-BT1 Rear left/right Speaker-level output 90 Hz and above + ACR-1 Speaker-level output 90 Hz and below + Notes: The +12V Power and Ground connections are not shown Speaker outputs 1 and 2: Stereo, 90 Hz and above, plays inputs 1 and 2, AccuBASS is on, ACR-1 adjusts level of all outputs Speaker outputs
LC-5.1300 ACR-1 Dash Control Installation Top Lid Removal The AudioControl ACR-1 dash control is a remote level for your LC-5.1300 amplifier. It may be mounted under the dash using its own enclosure, or through a custom hole in the dash. The knob should be within reach of the driver, and in a spot where the LED is plainly visible. Disconnect the vehicle battery +12V and Ground connections before installation.
Specifications All specifications are measured at 14.4 VDC (standard automotive voltage). As technology advances, AudioControl reserves the right to continuously change our specifications, like our Pacific Northwest weather, although we are working on a surround-sound umbrella as well. LC-5.1300 Multi-Channel Amplifier Power Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x 100 Watts @ 4 Ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LC-5.