AT-LPW40WN/AT-LPW30TK User Manual Belt-Drive Turntable
Introduction Thank you for purchasing this Audio-Technica product. Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference. This product can be used only in the countries where the product is sold. Make sure that the operating voltage and the plug of AC adapter of the product are correct for the country you live in.
Safety precautions Safety precautions Important information For customers in Canada Warning: • To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. IC statement: CAN ICES-3 (B)/NMB-3(B) Caution: • Do not expose this apparatus to drips or splashes. • To avoid electric shock, do not open the cabinet. • Refer servicing to qualified personnel only. • Do not expose this apparatus to excessive heat such as sunshine, fire or the like.
Part names and functions Overall diagram 1 2 3 4 7 5 6 8 1 Platter 2 Drive belt 14 9 10 11 9 Motor pulley 4 Spindle 5 Turntable mat 6 Control knob 8 Ground (earth) terminal Connect the RCA audio cable. Connect it to either the amplifier's PHONO input jack or its line input jack. The red terminal is the right channel and the white terminal is the left channel. 11 Output selector switch If connecting to an amplifier's PHONO input jack, set this switch to the PHONO position.
Part names and functions Tonearm 1 Counterweight 1 Balances the tonearm and adjusts to provide the proper tracking force. 2 2 Tracking force gauge ring Use to adjust and set the tracking force. 3 5 Tonearm lift Moves the tonearm vertically to and from the face of the record. 4 3 Tonearm rest with clamp 6 Use the clamp to secure the tonearm so that it does not move. 5 Anti-skate control dial 4 While the record is playing, a force acts on the stylus tip to pull it inward.
Preparation for use Leveling the turntable Placing the platter 1. After positioning the product where you want to use it, adjust the feet so that the product is level. This product requires some assembly before using it for the first time. Do not connect the AC adapter until assembly is complete. • Use a level (sold separately) as needed to ensure that the product is level. 1. Set the platter on the spindle.
Preparation for use Tonearm balance and tracking force Setting tracking force In order for the cartridge to reproduce audio correctly from the record’s grooves, the tonearm’s balance and tracking force must be adjusted to fit the specifications of the cartridge. If the tonearm’s balance and tracking force are not properly adjusted, the record or the cartridge’s stylus may become damaged.
Preparation for use • The RCA audio cable's red jack is for the right (R) channel, and the white jack is for the left (L) channel. Installing/removing the dust cover When attaching the dust cover, insert the hinges of the dust cover into the two dust cover hinge holders on the back of the body. When removing the dust cover, slowly pull the dust cover out from the dust cover hinge holders.
Playing a record 5. Lower the tonearm by moving the tonearm lift control lever to the DOWN position. The tonearm descends slowly onto the record and play begins. Before playing a record 1. Remove the cartridge’s protector. • Alternatively, you can skip steps 2 to 4, and use your fingers to lift the headshell, move the tonearm over the desired location on the record, and then place the headshell down to begin playing the record. • Do not subject the product to strong impact during playback.
Care Replacing the stylus Turntable body Removing the stylus • When the turntable body is dirty or dusty, first disconnect the AC adapter's cord from the power input jack, and then wipe off the dirt and dust with a soft, dry cloth. • Do not use benzenes, thinners, etc. • When storing the product for a long time, disconnect the AC adapter's cord from the power input jack and the power cable plug from the outlet then wrap the equipment in plastic; do not allow it to become damp.
Replacing a cartridge Replacing the belt Refer to the user manual for the cartridge that you will be using if you are replacing the cartridge included with this product with another, commercially available cartridge. After you replace the old cartridge with a new one, you must readjust the overhang and the tonearm’s balance and tracking force. • The belt is a consumable part. Replace the belt if the speed of playback slows down or irregular rotation occurs.
Adjusting the overhang When the turntable is moved The position of the cartridge must be accurately determined (adjusting the overhang) when mounting a cartridge or headshell other than the one provided. Using the product's original packing materials, wrap the turntable in the reverse order from when you unwrapped it. If you do not have the packaging materials, take the following measures: 1. Mount the cartridge so it is parallel to the headshell.
Troubleshooting Problem Solution The platter does not spin. • Is the AC adapter connected to the outlet? Connect AC adapter to the outlet. • Has the belt slipped from the platter? Correctly place the belt on the platter. • Is the belt placed on the motor pulley? Check that the belt is placed on the motor pulley correctly. • Has the belt been damaged? Replace it with a new belt. The platter spins, but there is no sound or the volume is not loud enough.
Specifications Turntable specifications General specifications Type Belt-drive manual turntable Power supply requirements 100 to 240 V, 50/60 Hz, 0.5 A Max. Motor AT-LPW40WN: DC servo with Active Speed Stabilization AT-LPW30TK: DC servo Power consumption Drive method Belt drive 110V 60Hz (US) - Working: 1.1 W - Motor off: 1.0 W - Power off: 0.1 W Speeds 33-1/3 RPM, 45 RPM Turntable platter Aluminum Die Casting Wow and flutter < 0.
Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan ©2019 Audio-Technica Corporation Global Support Contact: www.at-globalsupport.com 162501233-01-01 ver.1 2019.03.
