AT-LP7 IMPORTANT: Turntable belt needs to be attached or turntable will not operate. See page 5 for instructions. For assistance, contact our Audio Solutions Department at 330-686-2600 x5000 or audio-solutions@atus.com.
Introduction Thank you for purchasing this Audio-Technica product. Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference. This product can be used only in the countries where the product is sold. Make sure that the operating voltage and the plug of AC adapter of the product are correct for the country you live in.
Safety precautions Notes on use Important information Turntable body Warning: To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. EN Caution: Do not expose this apparatus to drips or splashes. To avoid electric shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not expose this apparatus to excessive heat such as sunshine, fire or the like. Do not subject this apparatus to strong impact.
Part names and functions Overall diagram 1 2 3 6 4 5 7 1 Motor pulley 2 Platter 3 Spindle 4 Power indicator 5 Control knob Use to start and stop, as well as select the platter's speed. 6 Tonearm For details, refer to “Tonearm” on p. 4. 7 Feet Adjust the level of the product. 8 7 8 9 10 11 12 Pre-amplifier selector switch If connecting to an amplifier's PHONO input jack, set this switch to the PHONO position.
Part names and functions Tonearm 1 Counterweight Balances the tonearm and adjusts to provide the proper tracking force. 5 Tracking force gauge ring Use to adjust the tracking force. 3 2 3 Tonearm lift Moves the tonearm vertically to and from the face of the record. 4 5 Tonearm height setting lever 6 Anti-skate control dial While the record is playing, a force acts on the stylus tip to pull it inward. This force can be counteracted by setting the same values for anti-skate and the tracking force.
Preparation for use Leveling the turntable Placing the platter This product requires some assembly before using it for the first time. Do not connect the AC adapter until assembly is complete. 1. After positioning the product where you want to use it, adjust the feet so that the product is level. • Use a level (sold separately) as needed to ensure that the product is level. 1. Set the platter on the spindle.
Preparation for use Tonearm balance and tracking force 1. While supporting the counterweight so that it does not move, turn the tracking force gauge ring so that its “0” position lines up with the centerline on the back of the tonearm. • The tracking force is not adjusted simply by turning the tracking force gauge ring. • Do not drag the cartridge’s stylus across the record or platter when adjusting the tonearm’s balance or tracking force. Doing so may damage the stylus.
Preparation for use Installing/removing the dust cover • The dust cover is designed to protect the product's sensitive components when the product is not in use. It should remain off while records are playing. • Using the dust cover during play may result in record damage or sound degradation. • Whenever putting on or taking off the dust cover, put it onto or take it off of the body slowly.
Playing a record Before playing a record 1. Return the cartridge's protector to its original up position. • Alternatively, you can skip steps 2 to 4, and use your fingers to lift the headshell, move the tonearm over the desired location on the record, and then place the headshell down to begin playing the record. • Do not subject the product to strong impact during playback. • If the tonearm is fixed to the tonearm rest, remove the clamp. Pausing the record EN 1.
Replacing the stylus Replacing a cartridge Removing the stylus • In addition to the deterioration of sound quality, records may also be damaged as the cartridge’s stylus tip wears down. • As a rule of thumb, replace the stylus after 300 hours of use. • Be sure to disconnect the product’s power cable plug from the outlet. 1. Release the headshell from the tonearm. • Fix the tonearm with the clamp and then remove the headshell gently. 2.
Adjusting the tonearm's height • The belt is a consumable part. Replace the belt if the speed of playback slows down or irregular rotation occurs. As a rule of thumb, we suggest replacing the belt once a year. • Before replacing the belt, be sure to disconnect the product’s power cable plug from the outlet. When installing a cartridge other than the one provided, you must maintain a suitable distance between the cartridge and the surface of the record.
Adjusting the overhang The position of the cartridge must be accurately determined (adjusting the overhang) when mounting a cartridge or headshell other than the one provided. 1. Mount the cartridge so it is parallel to the headshell. • Match up the positions of the cartridge and headshell to the figure below and mount the cartridge so it is parallel to the headshell. Overhang adjustment guide This illustration represents the actual size.
Troubleshooting Problem Solution The platter does not spin. • Is the AC adapter connected to the outlet? Connect AC adapter to the outlet. • Has the AC adapter's plug come off? Check whether or not the plug is properly attached to the AC adapter. • Has the belt slipped from the platter? Correctly place the belt on the platter. • Is the belt placed on the motor pulley? Check that the belt is placed on the motor pulley correctly. The platter spins, but there is no sound or the volume is not loud enough.
Specifications Turntable specifications General specifications Type Belt-drive manual turntable Power supply requirements 100 to 240 V, 50/60 Hz, 0.6 A Max. Motor DC motor Power consumption 5.5 W Drive method Belt drive AC Adapter 12 V, 2 A Speeds 33-1/3 RPM, 45 RPM Dimensions Turntable platter POM (polyoxymethylene) Wow and flutter < 0.08 % WRMS (33 RPM) at 3 kHz 450 mm (17.72") × 352 mm (13.86") × 157 mm (6.18") (W × D × H) Signal-to-noise ratio > 60 dB Weight 8.3 kg (18.
Memo EN 14
Visit our Web Site: www.audio-technica.com One-Year Limited Warranty Audio-Technica brand products purchased in the U.S.A. are warranted for one year from date of purchase by AudioTechnica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A.T.U.S.
Visite o nosso website: www.audio-technica.com Garantia limitada de um ano Produtos da marca Audio-Technica adquiridos nos EUA são garantidos por um ano a partir da compra pela AudioTechnica U.S., Inc. (A.T.U.S.) como livres de defeitos de materiais e mão de obra. No caso de tais defeitos, o produto será reparado imediatamente, sem despesas, ou segundo a nossa opção, substituído por um produto novo de valor igual ou superior se entregue para a A.T.U.S.
Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan ©2017 Audio-Technica Corporation Global Support Contact: www.at-globalsupport.com 162501140-01-01 ver.1 2017.11.