AT-LP140XP User Manual Direct-Drive Professional Turntable AT-LP140XP
Introduction Thank you for purchasing this Audio-Technica product. Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference. This product can be used only in the countries where the product is sold. Make sure that the operating voltage of the product is correct for the country you live in. Package contents Make sure that you have all the included items listed below before using this product.
Safety precautions Safety precautions Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product. 9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
Notes on use Turntable body • Do not set and use the product in locations that are considerably hot or humid, dirty, or subject to extreme vibrations. • The product should be positioned on a flat, level surface. Cartridge • Attach the protector to protect the stylus when the product is not in use. • Do not touch the stylus of the cartridge with your finger. • Do not allow the cartridge’s stylus to bump against the platter or the edge of the record.
Part names and functions Top view diagram 17 17 16 1 2 3 15 14 4 5 13 6 12 7 AT-LP140XP 8 1 45-RPM adapter (shown in receptacle) Adapts 7" records with large center holes to fixed center spindle. 2 4 Platter Felt mat 6 Power dial 11 Tempo range button Select +/-8 or 16% tempo range. +/-24% is selected by pressing both the +/-8% and 16% buttons simultaneously; both buttons should be illuminated. 12 Pitch selection indicator Shows blue for standard or locked RPM setting.
Part names and functions Front and rear view diagram 1 2 1 Dust cover 2 Feet 3 2 Adjust the level of the product. 3 Stereo output terminals Connect the RCA audio cable. Connect it to either the amplifier’s PHONO input jack. The red terminal is the right channel and the white terminal is the left channel. 4 Ground (earth) terminal Connect the amplifier’s ground (earth) terminal to this terminal using the RCA audio cable’s ground line. 5 AC inlet Use to connect the included power cable.
Part names and functions Tonearm 1 Counterweight 1 Balances the tonearm and adjusts to provide the proper tracking force. 2 2 Tracking force gauge ring 6 Use to adjust the tracking force. 3 7 Tonearm lift Moves the tonearm vertically to and from the face of the record. 4 3 Tonearm rest with clamp 8 Use the clamp to secure the tonearm so that it does not move. 5 5 4 Tonearm height adjustment dial Raises and lowers the tonearm to allow it to remain parallel to the record surface.
Preparation for use Leveling the turntable Placing the platter 1. After positioning the product where you want to use it, adjust the feet so that the product is level. This product requires some assembly before using it for the first time. Do not connect the power cable until assembly is complete. • Use a level (sold separately) as needed to ensure that the product is level. 1. Set the platter on the spindle.
Preparation for use Tonearm balance and tracking force Setting tracking force In order for the cartridge to pick up sound correctly from the record’s grooves, the tonearm’s balance and tracking force must be adjusted to fit the specifications of the cartridge. If the tonearm’s balance and tracking force are not properly adjusted, the record or the cartridge’s stylus may become damaged. 1.
Preparation for use Installing/removing the dust cover Connecting to connectable equipment (active speakers, amplifiers, etc.) • The dust cover is designed to protect the product’s sensitive components when the product is not in use. It should remain off while records are playing. • Using the dust cover during play may result in record damage or sound degradation. • Always remove and replace the dust cover carefully.
Playing a record Before playing a record Playing a record Lower the volume of the amplifier, speakers, etc., sufficiently. 1. Remove the cartridge’s protector. 1. Press the START/STOP button. • If the tonearm is fixed to the tonearm rest, unlatch the clamp. • The platter begins to rotate. Protector 2. Turn the power dial to the ON position. • The speed selector and strobe illuminator will light up. 3.
Playing a record 4. Lower the tonearm by moving the tonearm lift control lever to the DOWN position. The tonearm descends slowly onto the record and play begins. Pausing the record 1. After lowering the volume of the amplifier, speakers, etc., sufficiently, lift the tonearm with the tonearm lift control lever.
Care Replacing the stylus Turntable body Removing the stylus • When the turntable body is dirty or dusty, first disconnect the power cable plug, and then wipe off the dirt and dust with a soft, dry cloth. • Do not use benzenes, thinners, etc. • When storing the product for a long time, disconnect the power cable plug from the outlet and wrap the equipment in plastic; do not allow it to become damp.
Replacing a cartridge Adjusting the tonearm’s height Refer to the user manual for the cartridge that you will be using if you are replacing the cartridge (AT-XP3) included with this product with another, commercially available cartridge. After you replace the old cartridge with a new one, you must readjust the overhang and the tonearm’s balance and tracking force.
Troubleshooting Problem Solution The platter does not spin. • Is the power cable connected to the outlet? Connect the power cable to the outlet. • Has the power cable plug come off? Check whether or not the plug is properly attached to the product. The platter spins, but there is no sound or the volume is not loud enough. • Is the cartridge’s protector still in place? Remove the cartridge’s protector. • Is the tonearm in the lift position? Lower the tonearm.
Specifications Turntable specifications General specifications Type 3-speed, fully manual operation Power supply requirements 115 to 230 V AC, 50/60 Hz Motor High-torque DC motor Power consumption 6W Drive method Direct drive Dimensions Speeds 33-1/3 RPM, 45 RPM, 78 RPM Turntable platter Die-cast aluminum 452.0 mm (17.80") × 352.0 mm (13.86") × 158.6 mm (6.24") (W × D × H) Starting Torque > 2.2 kgf.cm Weight 10.0 kg (22.
Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan ©2019 Audio-Technica Corporation Global Support Contact: www.at-globalsupport.com 162501390-02-01 ver.1 2019.04.
