Product Installation Manual rL Digital Video Disc Player Model #’s: DVD-021-0x-x Document #540125 7300 Industry Drive, North Little Rock, AR 72117 Phone: 501-955-2929 Fax: 501-955-2988
AUDIO INTERNATIONAL, INC. 11/98 Revision History Rev. Level IR Date 11/98 Description Initial Release Applicable Documents Document # N/A 560032 Drawing # 522187 N/A Description DVD-021-0x-x Outline Drawing Operation Guide 2 Document #540125, Rev. IR, Model No.
AUDIO INTERNATIONAL, INC. 11/98 Service Bulletin List Service Bulletin # Subject Manual Revision # Manual Revision Date List of Illustrations Section No. Description 3 Document #540125, Rev. IR, Model No.
AUDIO INTERNATIONAL, INC. 11/98 Table of Contents Section Description Page 1.0 1.1 1.2 1.3 1.4 General Information………………………………………………….. Introduction……………………………………………………………... Purpose of the Equipment……………………………………………. Operational Features………………………………………………….. Optional Equipment……………………………………………………. 5 5 5 5 6 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 Installation…………………………………………………………….. Prior to Installation…………………………………………………….. Unpacking & Inspection………………………………………………..
AUDIO INTERNATIONAL, INC. 11/98 MODEL NO. DVD-021-0x-x Digital Video Disc Player 1.0 General Information 1.1 Introduction This manual contains information for the installation of the Audio International, Inc. (AI) Digital Video Disc Player, Model No. DVD-021-0x-x. The “-0x” in the model number represents the specific model number (-01, -02, 03). The “-x” suffix represents the type of connector utilized.
AUDIO INTERNATIONAL, INC. 1.4 11/98 Optional Equipment The front bezel of the units can be customized to match the interior style of any aircraft. They can be plated or painted to match any interior. AI source equipment is configured to accept digital infrared commands. Digital codes allow the source equipment to interface with an infrared handheld remote control (AI-RC1-17xxxx) via an infrared receiver, IFR-9A or IFR-485.
AUDIO INTERNATIONAL, INC. 2.3 11/98 Cautions & Warnings 2.3.1 All audio and video connections to the unit should be shielded and properly grounded. Perform a pin-to-pin check to confirm that all wires terminate in their proper location. It is important to do a power and ground check on the pin connections. Ensure that power and ground are applied only where required. 2.3.2 DO NOT connect or disconnect the unit while power is applied. 2.3.3 DO NOT remove any factory-installed screws.
AUDIO INTERNATIONAL, INC. 2.5 11/98 Physical Requirements 2.5.1 Refer to Section 5.0 for unit dimensions and attachment points. 2.5.2 Allow a minimum of 1” air space around the unit to allow for proper air circulation to prevent the build-up of internal heat. 2.5.3 The DVD-021-0x-x must not be mounted on its side, at an angle or in an inclined position. 2.6 Electrical Requirements 2.6.1 The DVD-021-0x-x utilizes one 15-pin connector for electrical connections.
AUDIO INTERNATIONAL, INC. 2.7 11/98 Pinouts / Descriptions The DVD unit connector with respective pin designations and descriptions are as follows: Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2.
AUDIO INTERNATIONAL, INC. 4.0 3.2 When the DVD reaches the end of the disc, the DVD will automatically stop playback. Once the DVD has stopped, the OPEN/CLOSE button on the front panel must be pressed to unload the disc. 3.3 If power is interrupted (>200 ms) or power drops below 18VDC while a disc is playing, the player will shut down. If a DVD disc is in the player, the unit will begin playback from the beginning of the disc automatically.
AUDIO INTERNATIONAL, INC. 5.2 11/98 Applicable Drawings: 5.2.1 The following diagrams show the unit dimensions, mounting hole locations, and connector locations of the DVD-021-0x-x. FRONT VIEW TOP VIEW 11 Document #540125, Rev. IR, Model No.
AUDIO INTERNATIONAL, INC. 11/98 BACK VIEW 12 Document #540125, Rev. IR, Model No.