BENUTZERHANDBUCH OWNER’S MANUAL CAR AUDIO SYSTEMS SE3500 D CLASS D MONO CAR AUDIO AMPLIFIER
INHALTSVERZEICHNIS SICHERHEITSHINWEISE 3 INSTALLATIONSHINWEISE 4 SE3500D 6 Funktionen und Bedienelemente 6 Anschlussbeispiel: Tiefpass-Modus (normaler Subwoofer-Betrieb) 7 Anschlussbeispiel: Master/Slave-Modus 8 EINSTELLBEREICH DER FILTER 10 TECHNISCHE DATEN 11 FEHLERBEHEBUNG 12 OPTIONALES ZUBEHÖR 14 OWNER’S MANUAL IN ENGLISH FROM PAGE 15 Dieses Symbol weist Sie auf wichtige Hinweise auf den folgenden Seiten hin.
SICHERHEITSHINWEISE BITTE BEACHTEN SIE DIE FOLGENDEN HINWEISE VOR INBETRIEBNAHME! DAS GERÄT NICHT AN STELLEN EINBAUEN, AN DENEN ES HOHER FEUCHTIGKEIT ODER STAUB AUSGESETZT IST. Bauen Sie das Gerät so ein, dass es vor hoher Feuchtigkeit und Staub geschützt ist. Wenn Feuchtigkeit oder Staub in das Gerät gelangen, kann es zu Betriebsstörungen kommen. Schäden am Gerät, welche durch Feuchtigkeit hervorgerufen wurden, unterliegen nicht der Garantie.
INSTALLATIONSHINWEISE HINWEIS! Bevor Sie mit der Installation des Soundsystems beginnen, trennen Sie unbedingt den Massepol der Fahrzeugbatterie ab, um Kurzschlüsse und Stromschläge zu vermeiden. MECHANISCHE INSTALLATION Achten Sie bei der Installation darauf, dass keine serienmäßig im KFZ vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw.entfernt werden. Vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung erhält.
INSTALLATIONSHINWEISE ELEKTRISCHE ANSCHLÜSSE 1 2 3 4 5 VOR DEM ANSCHLIESSEN Für den fachgerechten Anschluss des Soundsystems sind geeignete Kabelsets im Fachhandel erhältlich. Achten Sie beim Kauf auf einen ausreichenden Kabelquerschnitt (mind. 25 mm2), den passenden Sicherungswert sowie auf die Leitfähigkeit der Kabel. Säubern und entfernen Sie vorhandene Rost- und Oxidationsstellen an allen Kontaktpunkten der Batterie und an den Massepunkten.
SE3500D FUNKTIONEN UND BEDIENELEMENTE 1 2 3 4 5 6 7 8 9 10 11 1 Die LINE INPUT-Cincheingänge sind zur Ansteuerung mittels Cinch-Kabel mit dem Steuergerät zu verbinden. 2 Der optional verwendbare symmetrische Eingang (BALANCED INPUT) ist im Gegensatz zu normalen Cinchkabeln störunanfällig gegen Einstreuungen von der Fahrzeugelektronik. Es wird dazu ein Line-Überträger mit speziellem Kabel benötigt, der zwischen Steuergerät und dem Verstärker eingeschleift wird.
SE3500D ANSCHLUSSBEISPIEL: Tiefpass-Modus mit einem Subwoofer HINWEIS! Optional kann noch ein zweiter Subwoofer an die nicht belegten Anschlussklemmen angeschlossen werden. Dann muss die Impedanz pro Subwoofer 2 - 8 Ohm betragen.
SE3500D ANSCHLUSSBEISPIEL: Master/Slave-Modus mit zwei Verstärker Bass-Fernbedienung mittels beiliegendem Kabel mit dem Anschluss am Verstärker (MASTER) verbinden (REMOTE) 1. Stereo Cinch-Audiokabel (L/R od. SUB OUT) vom Steuergerät mit LINE INPUT L/R des MASTER- Verstärkers verbinden. 2. Stereo Cinch-Anschluss (SLAVE IN/OUT) vom MASTER- Verstärker mit SLAVE IN/OUT des SLAVE-Verstärkers verbinden. Steuerleitung REM SLAVE MASTER Schalterstellung = MASTER Schalterstellung = SLAVE 1. 2.
SE3500D ANSCHLUSSBEISPIEL: Subwoofer mit Single-Schwingspule MASTER HINWEIS! Hierbei müssen unbedingt die beiden ”–”-Lautsprecherausgänge der Verstärker Master und Slave verbunden werden. MASTER/SLAVE Link wie auf Seite 8 beschrieben. Subwoofer 2 – 8 Ohm SLAVE Die Impedanz des Subwoofers von 2 Ohm darf nicht unterschritten werden. ANSCHLUSSBEISPIEL: Subwoofer mit Dual-Schwingspule MASTER MASTER/SLAVE Link wie auf Seite 8 beschrieben.
EINSTELLBEREICHE DER FILTER LEVEL 0,7 V 4V 0,25 V 6V 0,2 V SUB SONIC 35 Hz 21 Hz 48 Hz 15 Hz 55 Hz LOW PASS 140 Hz 40 Hz 220 Hz 35 Hz 250 Hz EXTENDED BASS CONTROL SUB BOOST 9 dB 3 dB 15 dB 0 dB 18 dB FREQ RANGE 50 Hz 30 Hz 70 Hz 20 Hz 80 Hz PHASE 90° 30° 150° 0° 180° WIDE Q-CONTROL NARROW 0,5 0,4 0,7 0,3 1,0 Q = 0,3 Q = 1,0 +18dB +12dB +6dB 0dB 20Hz 40Hz 10 60Hz 80Hz
TECHNISCHE DATEN MODELLE SE3500D KANÄLE SCHALTUNGSPRINZIP 1 CLASS D Digital AUSGANGSLEISTUNG RMS 13,8 V Watt an 4 Ohm Watt an 2 Ohm Watt an 1 Ohm 1 x 600 1 x 1000 1 x 1750 AUSGANGSLEISTUNG MAX. 13,8 V Watt an 4 Ohm Watt an 2 Ohm Watt an 1 Ohm 1 x 1200 1 x 2000 1 x 3500 Dämpfungsfaktor Signal-Rauschabstand Klirrfaktor (THD&N) Eingangsempfindlichkeit Eingangsimpedanz 200 90 dB 0,1% 6 - 0.
FEHLERBEHEBUNG Fehler: keine Funktion Ursache: Lösung: 1. Die Stromversorgungskabel sind nicht korrekt angeschlossen. Erneute Überprüfung 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. Erneute Überprüfung 3. Die Remote-Steuerleitung des Steuergeräts (Autoradio) ist nicht korrekt am Verstärker angeschlossen. Erneute Überprüfung 4. Sicherungen defekt. Im Falle des Austauschs achten Sie bitte auf den korrekten Wert der Sicherungen.
FEHLERBEHEBUNG HINWEIS! SCHUTZ-SCHALTUNG Im Verstärker sind verschiedene elektronische Schutzsicherungen integriert. Bei Überlastung, Überhitzung, Kurzschluss an den Lautsprechern, aber auch bei zu niederohmigen Betrieb oder mangelhafter Stromversorgung schaltet dieser ab, um größeren Schäden vorzubeugen. Liegt eine der oben genannten Störungen vor, leuchtet die PROTECT LED (rot) auf. Prüfen Sie in diesem Fall alle Anschlüsse auf Fehler, wie. z.B. Kurzschlüsse, fehlerhafte Verbindungen oder Überhitzung.
OPTIONALES ZUBEHÖR BALANCED LINE TECHNOLOGIE BALANCED INPUT Mit dem symmetrischen Eingang bietet ESX absolute “State-of-the-Art”-Technologie. Diese aus der High End Studiound PA-Technik stammende Technologie, im Englischen Balanced Inputs genannt, ist im Gegensatz zu normalen Cinchkabeln störunanfällig gegen Einstreuungen und Interferenzen von der Fahrzeugelektrik. Es wird jedoch ein SignalTransmitter wie folgend beschrieben benötigt.
TABLE OF CONTENT SAFETY INSTRUCTIONS 16 INSTALLATION INSTRUCTIONS 17 SE3500D 19 Features and operational controls 19 Interconnection example Low Pass-Mode (standard subwoofer operation) 20 Interconnection example Master/Slave-Mode 21 FILTER SETTING RANGE 23 SPECIFICATIONS 24 TROUBLE SHOOTING 25 OPTIONAL ACCESSORIES 27 This symbol adverts you a important reference note on the following pages.
SAFETY INSTRUCTIONS PLEASE OBSERVE THE FOLLOWING ADVICES BEFORE THE FIRST OPERATION! DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT WILL BE EXPOSED TO HIGH HUMIDITY AND DUST. Install the device at a location, where it will be protected from high humidity and dust. If humidity and dust attain inside the device, malfunctions may be caused. THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE.
INSTALLATION INSTRUCTION REFERENCE NOTE Before you start with the installation of the sound system, disconnect by any means the GROUND connection wire from the battery, to avoid any risk of electric shock and short circuits. MECHANICAL INSTALLATION Avoid any damage removing of the components of the vehicle like wires, cables, board computer, seat belts, gastank or the like. Ensure that chosen location provide sufficient air circulation for the amplifier.
INSTALLATION INSTRUCTION ELECTRICAL INTERCONNECTION 1 2 3 4 5 BEFORE THE CONNECTION For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Ensure a sufficient profile section (at least 25 mm2), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection.
SE3500D FUNCTIONS AND OPERATIONAL CONTROLS 1 2 3 4 5 6 7 8 9 10 11 1 The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit. 2 The optional BALANCED INPUT is unlike the regular RCA-cables insusceptible against interspersion and interferences of the vehicle’s electronics. You need therefor a Balanced-Line-Transmitter with a special cable, which can be connected between the head unit and the amplifier. The Balance-Line-Transmitter is not included in delivery.
SE3500D INTERCONNECTION EXAMPLE Low Pass-Mode (Standard Subwoofer Operation) NOTE! A additional subwoofer can be connected to the non-occupied speaker outputs. In this case ensure a impedance of 2 - 8 ohms per subwoofer. Connect stereo RCA output (R/L or SUB OUT) of the headunit with LINE INPUT R/L of the amplifier Switch setting = MASTER R L Connect the bass remote controller and the remote terminal on the amplifier with the enclosed cable.
SE3500D INTERCONNECTION EXAMPLE Master/Slave Mode Remote wire REM Connect the bass remote 1. Connect Stereo RCA output (L/R controller and the remote terminal or SUB OUT) of the headunit with the at the amplifier (MASTER) LINE INPUT CH1/2 of the MASTER amp with the enclosed cable. 2. Connect Stereo RCA output (SLAVE IN/OUT) of the MASTER amp with the SLAVE IN/OUT of the SLAVE amp SLAVE MASTER Switch setting = MASTER Switch setting = SLAVE 1. 2.
SE3500D INTERCONNECTION EXAMPLE 1 Subwoofer with a Single-Voicecoil MASTER NOTE In this configuration both ”–” speaker outputs of the Slave and Master amp must be connected by any means. SLAVE MASTER/SLAVE Link like described on page 21. The Impedance may not be lower than 2 ohms. Subwoofer 2 – 8 Ohms INTERCONNECTION EXAMPLE 1 Subwoofer with a Dual-Voicecoil MASTER SLAVE MASTER/SLAVE Link like described on page 21.
FILTER SETTING RANGE LEVEL 0,7 V 4V 0,25 V 6V 0,2 V SUB SONIC 35 Hz 21 Hz 48 Hz 15 Hz 55 Hz LOW PASS 140 Hz 40 Hz 220 Hz 35 Hz 250 Hz EXTENDED BASS CONTROL SUB BOOST 9 dB 3 dB 15 dB 0 dB 18 dB FREQ RANGE 50 Hz 30 Hz 70 Hz 20 Hz 80 Hz PHASE 90° 30° 150° 0° 180° WIDE Q-CONTROL NARROW 0,5 0,4 0,7 0,3 1,0 Q = 0,3 Q = 1,0 +18dB +12dB +6dB 0dB 20Hz 40Hz 23 60Hz 80Hz
SPECIFICATIONS MODELS SE3500D CHANNELS CIRCUIT 1 CLASS D Digital OUTPUT POWER RMS 13,8 V Watts on 4 Ohms Watts on 2 Ohms Watts on 1 Ohms 1 x 600 1 x 1000 1 x 1750 OUTPUT POWER MAX. 13,8 V Watts on 4 Ohms Watts on 2 Ohms Watts on 1 Ohms 1 x 1200 1 x 2000 1 x 3500 Damping Factor Signal-to-Noise Ratio THD&N Input Sensitivity Input Impedance 200 90 dB 0,1% 6 - 0.
TROUBLE SHOOTING Malfunction: no function Reason: Remedy: 1. The power supply connection of the device is not correct. Recheck 2. The cabels have no mechanical or electrical contact. Recheck 3. The remote turn-on connection from the headunit to the amplifier is not correct. Recheck 4. Defective Fuses. In case of replacing the fuses, ensure by any means the correct fuse rating. Replace Fuses Malfunction: no signal on loudspeakers, but power LED lights up Reason: Remedy: 1.
TROUBLE SHOOTING REFERENCE NOTE PROTECTION CIRCUIT This amplifier owns a protection circuit. If overloading, overheating and shorted loudspeakers, or too low impedance or insufficient power supply is insisted, the amplifier shuts down to prevent serious damage. If one of this disfunctions is detected, the red PROTECT LED lights up. Check in this case all connections to detect short-circuits, faulty connections or overheating. Check the regarding notes on the previous page.
OPTIONAL ACCESSORIES BALANCED LINE TECHNOLOGY BALANCED INPUT With the optional BALANCED INPUTS, ESX offers an absolutely state-of-the-art-technology. Balanced inputs have been used for many years in professional sound studios and high end home stereo systems. Unlike the regular unbalanced RCA's connections, balanced wires are insusceptible against interferences of the vehicle's electronics. Therefor an separate signal transmitter like described below is required.
CAR AUDIO SYSTEMS Audio Design GmbH · www.audiodesign.de Am Breilingsweg 3 · D-76709 Kronau (Germany) Tel.