User manual WP205 & WP210 audac.
ADDITIONAL INFORMATION This manual is put together with much care, and is as complete as could be on the publication date. However, updates on the specifications, functionality or software may have occurred since publication. To obtain the latest version of both manual and software, please visit the Audac website @ www.audac.eu.
Table of contents Introduction 05 Wall panel - Microphone & line receiver � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 05 Precautions 06 Chapter 1 08 Overview front panel � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 08 Front panel description � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 08 Overview rear panel
04 WP2xx - User manual
Introduction Wall panel - Microphone & line receiver The WP205 & WP210 are remote wall mixers. The WP210 can be used with various AUDAC devices, while the WP205 is an external wall mixer designed to be used only with the ARES5A. It converts the signal coming from a stereo line-level audio source (such as a tuner, mobile devices, ...
Precautions READ FOLLOWING INSTRUCTIONS FOR YOUR OWN SAFETY ALWAYS KEEP THESE INSTRUCTIONS. NEVER THROW THEM AWAY ALWAYS HANDLE THIS UNIT WITH CARE HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS NEVER EXPOSE THIS EQUIPMENT TO RAIN, MOISTURE, ANY DRIPPING OR SPLASHING LIQUID. AND NEVER PLACE AN OBJECT FILLED WITH LIQUID ON TOP OF THIS DEVICE NO NAKED FLAME SOURCES, SUCH AS LIGHTED CANDLES, SHOULD BE PLACED ON THE APPARATUS DO NOT PLACE THIS UNIT IN AN ENCLOSED ENVIRONMENT SUCH AS A BOOKSHELF OR CLOSET.
WP2xx - User manual 07
Chapter 1 Overview front panel On the front side of the wall panel, there is an unbalanced 3.5 mm jack stereo line input connection available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together. Potentiometer for signal control Balanced microphone input Unbalanced stereo line input Front panel description Balanced microphone input A balanced microphone can be connected to this XLR input connector.
Overview rear panel WP205 The rear side of the WP205 contains an 8-pin Terminal Block connector. Below of the 8-pin connector are some DIP switches. With these switches certain functions can be switched on or off depending on the situation where the WP is in. Terminal block output connection DIP switch for phantom power DIP switch enable / disable output level +12 dBV DIP switch mono / stereo for Line or Mic Rear panel description WP205 8-pin terminal block (3.
Overview rear panel WP210 The rear of the WP210 contains an 8-pin Terminal Block connector, which is used to connect the wall panel to the RJ45 connector. Below the 8-pin connector is a 6-pin connector. This input connector is a duplicate of the line and mic input but for permanent connections. Below of the 6-pin connector are some DIP switches. These switches allow certain functions to be turned on or off, depending on the situation the WP is in.
DIP switches DIP switch enable / disable phantom power: The phantom power for the microphone input can be enabled or disabled. DIP switch enable / disable output level +12 dBV: When the option of +12 dBV is enabled, the wall panel is compatible with remote input devices. When it is disabled, the wall panel is compatible with standard line inputs (0 dBV) DIP switch mono / stereo: The operation mode can be switched between mono and stereo mode with this switch.
Connecting a remote input to a line input connection WP2xx series PRE116 PRE116 AUDAC 0 dBV output (DIP Switch) PSD241 Shielded balanced audio or CAT networking cable + Chapter 3 Connections CONNECTION STANDARDS The in- and output connections for AUDAC audio equipment are performed according to international wiring standards for professional audio equipment 3.
Wall panel rear audio input connection: 6-pin terminal block connector (3.5mm pitch) PIN 1: PIN 2: PIN 3: PIN 4: PIN 5: PIN 6: Mic GND Mic + Line L GND Line R 1 6 Terminal block (Audio, +24V DC) For connection to Wall Panels The 8-pin Euro-Terminal Block on the rear side of the WP205 or WP210 should be connected to twisted pair cabling. The maximum cable distance between the input unit and the speaker system can reach up to 100 meter.
Technical specifications Inputs Type Stereo unbalanced line Connector Front: 3.5mm jack Rear: 6-pin terminal block 3.81mm (for WP210 only) Impedance 7,7 kOhm Sensitivity -6 dBV / +26 dBV THD+N <0,2% Signal / Noise 72 dB Type Balanced microphone Connector Front: female XLR Rear: 6-pin terminal block 3.81mm (for WP210 only) Output Impedance 1 kOhm Sensitivity -45 dBV / -10 dBV THD+N <0,02% Signal / Noise > 75 dB Type Stereo Connector 8-pin terminal block 3.
Notes WP2xx - User manual 015
Discover more on audac.