AU7 User Manual Revision: 10 Revision Date: 2012/06/25 ATrack Technology Inc. Tel: +886-2-27975852 3F., No. 88, Sec. 1, Neihu Rd., Neihu Dist., Fax: +886-2-27974030 Taipei City 11493, Taiwan (R.O.C.) http://www.atrack.com.
Confidential Document Contents 1. Notification .............................................................................................................................. 3 1.1. Disclaimer .................................................................................................................................... 3 1.2. Copyright ...................................................................................................................................... 3 1.3. Warning ..................
Confidential Document 1. Notification 1.1. Disclaimer This document, and all other related products, such as device, firmware, and software, is developed by ATrack Technology Inc. thoroughly. At the time of release, it is most compatible with specified firmware version. Due to the functionalities of the devices are being developed and improved from time to time, the change in the protocol, specification, and firmware functions are subjects to change without notice. ATrack Technology Inc.
Confidential Document 2. Hardware 2.1. Package Content Each package contains the following device/accessories: Device * 1 CDMA Antenna * 1 GPS Antenna * 1 Power/IO Cable * 1 Serial Cable * 1 © ATrack Technology Inc. All Rights Reserved.
Confidential Document 2.2. Pin Assignments 2.2.1. Serial Cable (JST Female Connector to DB9 Female Connector) The Pin 9 is a power output port to provide a 5V, 300mA power source for accessory that connects to the serial port. If the connected accessory requires more power, please use external power source instead. 2.2.2. Power/IO connector (Male; On Device) Positive Inputs: IN0, IN1 (Triggered when connects to V+ range from 3.
Confidential Document 2.3. Installation When installing the device onto the vehicle, it is necessary to make sure that the direction of the device is following the picture demonstrated in the below picture, in order to have the G-Sensor working properly for harsh driving event detections. The forces on the axes are used to determine the harsh driving event status, hence if the installation is not able to be like in the picture, it is suggested to use GPS for detection instead.
Confidential Document 3. Firmware Upgrade 3.1. Firmware Upgrade by serial connection (1) Run HyperTerminal program © ATrack Technology Inc. All Rights Reserved.
Confidential Document (2) Enter a name for the connection (3) Choose COM port and click [Configure…] button. © ATrack Technology Inc. All Rights Reserved.
Confidential Document (4) Choose 57600,8,N,1 None flow control properties and click [OK] button. (5) Click [File][Properties] © ATrack Technology Inc. All Rights Reserved.
Confidential Document (6) Click [Settings] tab and [ASCII Setup…] button (7) Checked the following option and click [OK] button © ATrack Technology Inc. All Rights Reserved.
Confidential Document (8) Power ON the device. The startup message will show on the screen. (9) Type “AT$FWDL” command and press [Enter] key. Choose [Transfer][Send File…] © ATrack Technology Inc. All Rights Reserved.
Confidential Document (10) Choose the firmware filename which is provided by ATrack and select [Ymodem] Protocol option and click [Send] button. (11) When [Send] button is clicked, the file transfer progress will show as below: © ATrack Technology Inc. All Rights Reserved.
Confidential Document (12) When file sending is completed, the device will program and restart itself automatically. 3.2. LED Indications LED Indication Description Solid On In full operation mode 1 blink (0.1 sec.) in every 10 sec. In sleep mode PWR (Green) GPS module off, External power lost, running on 1 sec. On, 1 sec. Off backup battery 0.7 sec. On, 0.7 sec. Off Searching GPS signal Solid On Position get fixed Off CDMA module off 0.7 sec. On, 0.7 sec. Off Searching CDMA signal 0.2 sec.
Confidential Document 4. Appendix 4.1.
Confidential Document 4.2. FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.