AT1(E)Pro/AT3(E) User Manual Revision: 03 Revision Date: 2010/10/29 ATrack Technology Inc. Tel: +886-2-27975852 9F, No. 285, Sec. 2, Tiding Blvd., Fax: +886-2-27974030 Neihu Dist., Taipei City 11493, Taiwan (R.O.C.) http://www.atrack.com.
Confidential Document Contents 1. Notification ..............................................................................................................................3 1.1. Disclaimer .................................................................................................................................... 3 1.2. Copyright ..................................................................................................................................... 3 1.3. Warning ....................
Confidential Document 1. Notification 1.1. Disclaimer This document, and all other related products, such as device, firmware, and software, is developed by ATrack Technology Inc. thoroughly. At the time of release, it is most compatible with specified firmware version. Due to the functionalities of the devices are being developed and improved from time to time, the change in the protocol, specification, and firmware functions are subjects to change without notice. ATrack Technology Inc.
Confidential Document 2. Hardware 2.1. Package Content Each package contains the following device/accessories: • Device * 1 (one of the devices below) AT1Pro AT1EPro AT3 AT3E • GPS Antenna * 1 for AT1EONLY • Serial Cable * 1 • Power/IO Cable * 1 Note: The label of the device with GPS antenna built-in has to be placed toward sky. If the label side is not facing up, or is covered by metal or thick objects, the GPS reception quality will be degraded dramatically. © ATrack Technology Inc.
Confidential Document 2.2. Pin Assignments 2.2.1. Serial Cable (JST Female Connector to DB9 Female Connector) 2.2.2. Power/IO connector The Power/IO connector pin assignment is shown on the device. Positive Inputs: ACC (Triggered when connects to V+ range from 3.7 ~ 40V) Negative Inputs: IN1 (Triggered when connects to ground range from 0.8 ~ 0V) All outputs are open collector type (grounded when enabled) with max. sink current of 300mA. © ATrack Technology Inc. All Rights Reserved.
Confidential Document 3. Firmware Upgrade 3.1. Firmware Upgrade by serial connection (1) Run HyperTerminal program © ATrack Technology Inc. All Rights Reserved.
Confidential Document (2) Enter a name for the connection (3) Choose COM port and click [Configure…] button. © ATrack Technology Inc. All Rights Reserved.
Confidential Document (4) Choose 57600,8,N,1 None flow control properties and click [OK] button. (5) Click [File]à[Properties] © ATrack Technology Inc. All Rights Reserved.
Confidential Document (6) Click [Settings] tab and [ASCII Setup…] button (7) Checked the following option and click [OK] button © ATrack Technology Inc. All Rights Reserved.
Confidential Document (8) Power ON the device. The startup message will show on the screen. (9) Type “AT$FWDL” command and press [Enter] key. Choose [Transfer]à[Send File…] © ATrack Technology Inc. All Rights Reserved.
Confidential Document (10) Choose the firmware filename which is provided by ATrack and select [Ymodem] Protocol option and click [Send] button. (11) When [Send] button is clicked, the file transfer progress will show as below: © ATrack Technology Inc. All Rights Reserved.
Confidential Document (12) When file sending is completed, the device will program and restart itself automatically. © ATrack Technology Inc. All Rights Reserved.
Confidential Document 4. Appendix 4.1.
Confidential Document 4.2. FCC Regulations: l This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. l This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.