User's Manual

Industrial Serial Gateway
Industrial Modbus Gateway
Industrial Modbus Concentrator
Industrial Protocol Gateway
SE5901B/MB5901B/PG5901B Series
89900500G
Updated in November, 2016
Version V1.0
Inside the package you will find the following items:
 Industrial 3G/4G Serial Gateway x 1 or
 Industrial 3G/4G Modbus Gateway x 1 or
 Industrial 3G/4G Modbus Concentrator x 1 or
 Industrial 3G/4G Protocol Gateway x 1
 3-Pin 5.08mm Lockable Terminal Block
(Already mounted to the device) x 1
 2x7 Pin 3.5mm Lockable Terminal Block (IO version only) x 1
 DIN-Rail Kit (Already mounted to the device) x 1
 Installation Guide with Warranty Card x 1
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that maycause undesired operation.
Notice:
Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digitaldevice, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not nstalled and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
The antenna(s) used for this transmitter must not be co-located of operating in
conjunction with any other antenna or transmitter.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. Ln order to avoid the possibility of exceeding the
Fcc radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8inches) during normal operation.
Never install or work on electrical or cabling during periods of
lightning activity.
Never connect or disconnect power when hazardous gases
are present.
Warning:Hot Surface Do Not Touch.
IndoorIndoor
This equipment should be installed indoor and not connect directly
with equipment installed outdoor.
TOP View Bottom View
7
1
2
3
4
5
6
1. Grounding Screw
2. SMA Connector for Antenna
(4G version only)
3. Frame Ground
4. Terminal for Power
5. USB2
6. PWR Reset
7. SMA Connector for Antenna
(4G version only)
Front View
3G DB9 Type
1~4
5
11
12
13
14
4G DB9 Type
1~4
5
11
12
13
4G IO Type
1~4
6
7~10
11
12
13
3G IO Type
1~4
6
7~10
11
12
13
14
1. PWR LED
2. RUN LED
3. COM1 Tx LED
4. COM1 Rx LED
5. 9-Pin Male D-Sub Connector
for RS-232/485
6. 14-Pin 3.5 mm Terminal Block
for RS-232/485(COM1),
RS-232(COM2), Relay, and DI
7. Relay2 LED
8. Relay1 LED
9. DI2 LED
10. DI1 LED
11. Default Button
12. PWR USB
13. 10/100/1000 BASE-T(X) Ports
14. SMA Connector for Antenna
(D3G version only)
The device's
ground the device properly
1
2
4
5.
3. Proceed then to fix the antennas to the
female RP-SMA connectors deemed to
(Fig. 3). You can then choose whether
to plug in the I/O ports at this point or do
it later depending on the actual location
of the device or level of comfort for
performing such operation.
3
4
5
2
1
5