We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. Howeve r, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: 1-888-996-2729 FAX: 1-866-873-3531 gameroom@escaladesports.com Or write to: Escalade Sports Customer Service Department P.O. Box 889 Evansville IN 47706 Please have your model number when inquiring about parts.
IMPORTANT! READ EACH STEP IN THIS MANUAL BEFORE YOU BEGIN THE ASSEMBLY. TWO ADULTS ARE REQUIRED TO ASSEMBLE THIS BLAZER 7FT HOCKEY TABLE Tools Required: T1 - Wrench (Included) Phillips Screwdriver Furniture Polish and Cloth Assembly Tips Make sure you understand the following tips before you begin to assemble your hockey table. 1. Start all bolts by hand before tightening. 2. Some drawings or images in this manual may not look exactly like your product.
HARDWARE IDENTIFIER ( To Scale) H1 - 8mm x 38mm Hex Bolt (8 pcs) H2 - 8mm x 19mm Flat Washer (8 pcs) H3 - 3.5mm x 28mm Phillips Washer Head Screw (12 pcs) (Not to Scale) H4 - 4mm x 25mm Phillips Washer Head Screw (8 pcs) H5 - 4mm x 12mm Phillips Round Head Screw (4 pcs) ! All Rights Reserved. © 2012 Escalade Sports T1 - Wrench (1 pc) WARNING: CHOKING HAZARD Small parts. Not for children under 3 yrs.
PARTS IDENTIFIER ( Not to Scale) P1 - Hockey Table Cabinet (1 pc) P2 - Right Leg (2 pcs) P5 - Side Leg Panel (2 pcs) P4 - End Leg Panel (2 pcs) P3 - Left Leg (2 pcs) P6 - Puck Catcher (2 pcs) P7 - Leg Leveler (4 pcs) NOTE: P4 End Leg Panels are packed under the table cabinet and underneath styrofoam block. ACCESSORY IDENTIFIER (Not to Scale) A1 - Striker (4 pcs) A2 - Puck (4 pcs) A3 - Felt Pad (4 pcs) NOTE: A3 Felt Pads may already be attached to A1 Strikers. ! All Rights Reserved.
PARTS REQUIRED: 8 pcs - H1 Hex Bolt 8 pcs - H2 Flat Washer 1 pc - P1 Hockey Table Cabinet 2 pcs - P2 Right Leg 2 pcs - P3 Left Leg 1 pc - T1 Wrench STEP 1: To assemble this table, leave P1 Hockey Table Cabinet face down in the carton lid. Attach P2 Right Legs and P3 Left Legs using H1 Hex Bolts with H2 Flat Washers as shown in FIGURE 1. Do not tighten H1 Hex Bolts on this step until end of Step 3.
PARTS REQUIRED: 12 pcs - H3 Phillips Washer Head Screw 8 pcs - H4 Phillips Washer Head Screw 2 pcs - P4 End Leg Panel 2 pcs - P5 Side Leg Panel STEP 2: Attach P4 End Leg Panels between two legs of P2 Right Legs and P3 Left Legs using pre-drilled pilot holes with H3 Screws as shown in FIGURE 2. Tighten, but do not strip out H3 screws. P2 P4 P3 FIGURE 2 P3 P4 P2 H3 H3 NOTE: P4 End Leg Panels are packed under the table cabinet and underneath styrofoam block.
PARTS REQUIRED: 4 pcs - H5 Phillips Round Head Screw 2 pcs - P6 Puck Catcher 4 pcs - P7 Leg Leveler STEP 4: Attach P6 Puck Catchers on the inside of end apron using pre-drilled pilot holes with H5 Screws as shown in FIGURE 4. Tighten, but do not strip out H5 screws. Thread P7 Leg Levelers into the Leg assembly as shown in FIGURE 4. P7 P7 P7 P7 P6 H5 FIGURE 4 Under the table, remove screw using a small phillips screwdriver and open the battery box.
STEP 5: Peel the backing off A3 Felt Pad and attach to A1 Striker as shown in FIGURE 5. A3 FIGURE 5 NOTE: A3 Felt Pads may already be attached to A1 Strikers. A1 Congratulations! You have now assembled your Atomic Hockey Table. Please note the instructions below to ensure many years of trouble free use of your Atomic Hockey Table. CARE AND USE OF YOUR ATOMIC HOCKEY TABLE 1. Use only a suitable 120v AC household outlet, and insure the cord is not a trip hazard. 2.
ELECTRONIC SCORER OPERATION: 1. Under the table, remove screw using a small phillips screwdriver and open the battery box. Insert 4(four) pcs AA batteries (not included) in the order of polarity as shown on the inside cover. Then close using a small phillips screwdriver. (If the game will not be used for a long period of the time, we recommend that the batteries be removed). 2. Turn on the scorer using the on/off switch located on the scoring display.
PRODUCT PARTS LIST FOR MODEL # G03510W Key # H1 H2 H3 H4 H5 T1 P1 P2 P3 P4 P5 P6 P7 A1 A2 A3 C1 C2 C3 C4 C5 C6 C7 C8 K1 M1 Part # 03510WJH1 03510WJH2 03510WJH3 03510WJH4 03510WJH5 03510WJT1 03510WJP1 03510WJP2 03510WJP3 03510WJP4 03510WJP5 03510WJP6 03510WJP7 03510WJA1 03510WJA2 03510WJA3 03510WJC1 03510WJC2 03510WJC3 03510WJC4 03510WJC5 03510WJC6 03510WJC7 03510WJC8 03510WJK1 03510WJM1 All Rights Reserved. © 2012 Escalade Sports Qty. Description 8mm x 38mm Hex Bolt 8mm x 19mm Flat Washer 3.
90 DAY LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of 90 days from the original purchase.
Nosotros tratamos de asegurarnos que nuestros productos sean de la más alta calidad y libre de problemas, como defectos de fabricación ó partes incompletas. Sin embargo, Si usted tiene algún problema con su producto, por favor NO LO REGRESE A LA TIENDA pongase en contacto con nosotros llamando gratis al: 1-888 -996-2729 FAX : 1-866-873-3531 gameroom@Escalade Sports.com O escriba a: Escalade Sports Departamento de Atención al Cliente P.O.
IMPORTANTE! LEA TODOS LOS PASOS DE ESTE MANUAL ANTES DE COMENZAR A ARMAR. IMPORTANTE! LOS DIBUJOS DE ESTE MANUAL PUEDEN HABERSE EXAGERADO O MODIFICADO PARA MOSTRAR LOS DETALLES. SE REQUIEREN DOS ADULTOS PARA ENSAMBLAR ESTA MESA DE HOCKEY “BLAZER”. Herramientas Necesarias: T1 - Llave Allen (Incluida) Desarmador Phillips Abrillantador para muebles y un paño Consejos de ensamblamiento Asegúrese de que comprende los siguientes consejos antes de comenzar a armar la mesa. 1.
IDENTIFICADOR DE TORNILLOS ( A Escala) H1 - 8mm x 38mm Tornillo (8 pzas.) H2 - 8mm x 19mm Rondana (8 pzas.) H3 - 3.5mm x 28mm Tornillo Phillips (cabeza tipo arandela) (12 pzas.) (No a Escala) H4 - 4mm x 25mm Tornillo Phillips (cabeza tipo arandela) (8 pzas.) H5 - 4mm x 12mm Tornillo Phillips (Cabeza redonda) (4 pzas.) ! Todos los derechos reservados. © 2012 Escalade Sports T1 - Llave (1 pza.) ADVERTENCIA: PELIGRO DE ASFIXIA Piezas pequeñas. No adecuadas para niños menores de 3 años.
IDENTIFICADOR DE LAS PARTES ( No a Escala) P1 - Mesa de hockey de aire (1 pza.) P4 - Tabla del extremo para las patas (2 pzas.) NOTA: Las Tablas del extremo para las patas P4 están empacadas debajo del gabinete de la mesa y debajo del bloque de unicel. P2 - Pata (Derecha) (2 pzas.) P6 - Recipiente de Discos (2 pzas.) P5 - Tabla lateral para las patas (2 pzas.) P3 - Pata (Izquierda) (2 pzas.) P7 - Nivelador de las patas (4 pzas.) IDENTIFICADOR DE ACCESORIOS (No a Escala) A1 - Mazo (4 pzas.
PARTES REQUERIDAS: 8 pzas. - H1 Tornillo 2 pzas. - P2 Pata (Derecha) 8 pzas. - H2 Rondana 2 pzas. - P3 Pata (Izquierda) 1 pza. - P1 Mesa de hockey de aire 1 pza. - T1 Llave PASO 1: Para ensamblar esta mesa, coloque el Gabinete de la Mesa de Hockey P1 boca abajo sobre el cartón extendido. Coloque las Patas derechas P2 y las patas izquierdas P3 utilizando los Tornillos H1 con las Rondanas H2 como se muestra en la FIGURA 1. No apriete los tornillos H1 en este paso, sino hasta el final del paso 3.
PARTES REQUERIDAS: 12 pzas. - H3 Tornillo Phillips (cabeza tipo arandela) 2 pzas. - P4 Tabla del extremo para las patas 8 pzas. - H4 Tornillo Phillips (cabeza tipo arandela) 2 pzas. - P5 Tabla lateral para las patas PASO 2: Coloque las Tablas del Extremo P4 entre las dos Patas Derechas P2 y las Patas Izquierdas P3 usando los orificios guía pre-perforados con los Tornillos H3 como se muestra en la FIGURA 2. Atornille bien los tornillos H3, pero no los sobre apriete para no barrerlos.
PARTES REQUERIDAS: 4 pzas. - H5 Tornillo Phillips (Cabeza redonda) 2 pzas. - P6 Recipiente de Discos 4 pzas. - P7 Nivelador de las patas PASO 4: Coloque el Recipiente de Discos P6 en el interior del Panel del Extremo usando los orificios guía pre-perforados con los Tornillos H5 como se muestra en la FIGURA 4. Atornille bien los tonillos H5, pero no los sobre apriete para no barrerlos. Coloque los Niveladores P7 en las Patas ya ensambladas como se muestra en la FIGURA 4.
PASO 5: Despegue la protección del pegamento del Fieltro A3 y colóquela al Mazo A1 como se muestra en la FIGURA 6. A3 FIGURA 5 NOTA: Fieltro A3 puede venir ya pegado en los mazos A1. A1 Felicidades! Ahora ya ha terminado de ensamblar su mesa. Por favor, Siga las instrucciones del uso y el cuidado de su mesa abajo mencionadas, para garantizar muchos años sin problemas el juego de su mesa. INSTRUCIONES DEL CUIDADO Y USO DE SU MESA ATOMIC 1.
FUNCIONAMIENTO DEL MARCADOR ELECTRÓNICO: 1. Debajo de la mesa se encuentra la caja de la batería, ábrala quitándole el tornillo con un destornillador Phillips pequeño e Inserte 4 (cuatro) pilas AA (no incluidas) en el orden de la polaridad como se muestra en la contratapa. Luego ciérrela utilizando el destornillador Phillips pequeño. (Si no se utiliza el juego durante un período largo de tiempo, se recomienda que se retiren las pilas) 2.
LISTA DE PARTES PARA EL MODELO # G03510W Clave N.º de Parte H1 H2 H3 H4 H5 T1 P1 P2 P3 P4 P5 P6 P7 A1 A2 A3 C1 C2 C3 C4 C5 C6 C7 C8 K1 M1 03510WJH1 03510WJH2 03510WJH3 03510WJH4 03510WJH5 03510WJT1 03510WJP1 03510WJP2 03510WJP3 03510WJP4 03510WJP5 03510WJP6 03510WJP7 03510WJA1 03510WJA2 03510WJA3 03510WJC1 03510WJC2 03510WJC3 03510WJC4 03510WJC5 03510WJC6 03510WJC7 03510WJC8 03510WJK1 03510WJM1 Todos los derechos reservados. © 2012 Escalade Sports Cant.