FCC Certification Scenarios for Atmel ZigBits on Customers' products Features • Covers FCC certification scenarios for Atmel ZigBits’ usage • Analyzes the custom products possibilities and likely-hoods for successful certification 1 Introduction Atmel’s Wireless applications play vital role in providing IEEE 802.15.4 – compliant, ZigBee, and 6LoWPAN wireless solutions using family of RF devices such as ZigBits, AT86RFxxx,and MegaRF single chip solutions.
Overview This application note describes an overview of the Certification Scenarios possible when a designer uses the Atmel ZigBits portfolio. It also covers the changes that affect Atmel’s existing certification due to minor or major changes on designer’s hardware. 3 Atmel’s Range of ZigBit Modules and usage scenarios in customer products 3.1 ATZB-24-A2 It is a ZigBit Module with Dual Chip Antenna, a low-power, 802.15.
AVR[appnote nr] 3.1.3 Scenario # 2 When designers use the ATZB-24-A2 module on their base board and if there are additional circuits on the base board, with the additionally added circuits comprising of another radio or switching circuits, the radiations caused by the new circuits may or may not affect the performance of the ATZB-24-A2.
the antenna connectors, because they are standard connectors. The position of the Antenna cable is not really fixed as part of this product, and hence the module must be re-certified. If there are additional circuits on the base board, with the additionally added circuits comprising of another radio or switching circuits, the radiations caused by the new circuits may or may not affect the performance of the ATZB-A24-UFL.
AVR[appnote nr] Figure 3-3. ATZB-24-B0 3.3.1 Certification scenarios The following scenarios explain the usage of the ATZB-24-B0 module on customer’s base board. 3.3.2 Scenario # 1 The ATZB-24-B0 module is bought by designers and used on a base board. Atmel’s ATZB-24-B0 Module has been certified under Limited Modular category of FCC part 15 subpart C. Limited modular certification applies to modules that do not fully meet the requirements for a single modular certification.
3.4 ATZB-900-B0 ATZB-900-B0 is an ultra-compact, low-power, high-sensitivity 868MHz / 915MHz 802.15.4/ZigBee OEM module from Atmel. ATZB-900-B0 modules eliminate the need for costly and time-consuming RF development, minimizes bill of materials (BOM), and shortens time to market for a wide range of wireless applications, while embedded 802.15.4 / ZigBee software ensures standards-based wireless connectivity. Figure 3-4. ATZB-900-B0 3.4.
AVR[appnote nr] 3.4.3 Scenario # 2 In cases were usage explained in Scenario #1 applies and additionally, application dependent circuits as explained in Appendix A is used on the Base board, this scenario applies. If the circuits on the customer’s base board are either Intentional or Unintentional Radiators or both, then the customer has to certify the entire product carrying the ATZB-900-B0 Module.
Designers are required to re-certify their products carrying this module as this module brings out the UnBalanced RF Output without ending up in any antenna structure on the module. Since there is RF signal flowing on the designer’s base board in such case, the entire product has to be re-tested and certified. The new FCC ID obtained by the designer has to be used to meet regulatory requirements.
AVR[appnote nr] 4.3 Taiwan In Taiwan, NCC (National Communications Commission) approval is required for the end product using ZigBits. In-country testing is required since FCC / CE certifications are not accepted. ETSI / FCC will be the reference standard for certification regulations. The probability of getting certified is high in case if the products already hold FCC / CE certification. 4.
3. Secondary or another radio part When the above mentioned blocks are bought out items and are already pre-certified individually, the designer is expected to verify the entire product with FCC accredited Lab. The ZigBit’s FCC ID is still valid but cannot be used as a final product’s FCC ID because there are additional circuits in the product.
AVR[appnote nr] 6.
√ 12 √ Recertification; Probability of successful certification depends on Additional circuits on baseboard.
Disclaimer Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 U.S.A. Tel: (+1) (408) 441-0311 Fax: (+1) (408) 487-2600 Atmel Asia Limited Unit 01-5 & 16, 19F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun, Tong, Kowloon HONG KONG Tel: (852) 2245-6100 Fax: (852) 27232-1369 Atmel Munich GmbH Business Campus Parkring 4 D- 85748 Garching b. MUNICH Tel.: (+49) 89-31970-111 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg.