After entering PIN code, click Next. Select SPP-R200 from the list. *Default PIN code for SPP-R200 printer is “0000”. Select Serial Port Select New Outgoing Port from COM Ports tab. Select SPP-R200. Select COM 2 and click Finish.
* If the device information is not displayed correctly, please try Add New Devices again. * PIN code used in pairing can be mutually set on devices. * After the normal pairing, S/W, SDK etc. provided from Bluetooth manufacturer can be used for further Bluetooth services. 3.3 Bixolon SPP-R200 Printer Demo SPP-R2000 of Bixolon’s leading mobile printer is used for Bluetooth Print demonstration. Application listed on the homepage was used for the test.
4. Phone 4.1 Turn T on the e phone 1. [Home] -> [Phone] Phone] 2. [Start]->[P he keypad. from th 3. Press 4.2M Making a ph hone call Icon Desc cription D Delete the numbers. Speed dial ca S an be used to o call the pre e-stored num mber by pressing on o according g number. (S Speed dial can c ave up to 98 8 numbers.) sa C History. Call Ta enables the Talk t calling. The spee ed dial number is press sed for a few w seconds for the speed dial calls.
.3 Receiving calls Icon Description Receives the incoming calls. Rejects the incoming calls. Receiving call messages may be displayed differently. 4.4Hanging up calls Icon Description Use Speaker phone. Use Mute. Put the current phone call on hold state. After putting the call on hold, add another call. Contact can be used for search/add/delete of contacts. End calls.
4.5Switching calls Icon Description Put the current call on hold and the call that was on hold back to call state. 5. Contacts 5.1Contacts 1. [Home] -> [Contacts] 2.
5.2 Search for Contacts Enter a name for searching. 5.3 Adding New Contacts Select a contact type. Click on the button to add new contacts.
6. Text Message 6.4 Replying to the Text Message Click on the Reply. Click on the message from the Inbox Enter the messages and click on the button to send.
7. GPS Module GPS Module can be selected as an option in AT870N, and GPS Module is built-in at the top of the handheld. GPS program port: GPD1 GPS hardware port: COM6, 9600 7.1GPS Demo Program Run application - [Start Button] -> [DEMO_GPS_WM] Main Window - Start: Start receiving GPS Data - Stop: Stop receiving GPS Data Checking on GPS Data Reception: 1. The reception has to be checked in an open area. 2. The reception time for GPS Data can be different depending on the environments.
8.1 Camera Run application - [Start Button] -> [Pictures & Videos] -> [Camera] Main Window - Thumb…: Close the main window and go to Pictures & Videos screen. - Menu: Menu popup - To save screen, press “Enter” from the keypad. 9. HF13.56MHz The handheld can be equipped with HF13.56Mhz module internally. According to ISO standards, it can read tags from 3~8.5cm distance (For Mifare, the distance is 1~3.5cm). 9.1RF13.
- Open: Open HF device - Antenna: Stops the antenna signal. - Perform: Run the selected command from combo box. - ISO>: Change to ISO-15693 command screen. - Block: Number of Block be accessed. - Key Type: Key type of Block to be accessed. - Key Set: Key set of Block to be accessed. ISO-15693 Window -
10. Smart Card Device The handheld can communicate with IC Card via ISO-7816. 10.1Smartcard Program Run application - [Start Button] -> [DEMO_SAM] Main Window - Slot Status: Check the status of the slot. - PowerOn: Authorize the power of smart card device. - PowerOff:Unauthorize the power of smart card device. - SetParam: Set protocol type, clock rate, bit rate etc. of the card device. - GetParam: Read protocol type, clock rate, bit rate etc. of the card device. - Default: Set to default settings.
11. UHF 900 0Mhz The handheld can be equip pped with UHF U 900Mhz. It can rea ad or write E EPC GEN2 2 protocol RFID D tags. The frequency range is 85 50 ~ 960Mh hz which ca an be adjustted according to the coun ntries. UHF Reader 11.1 UHF 900M Mhz Program m Run app plication - [Start Button] B -> [DE EMO_UHF] Main Wiindow - Start: Start S the Inve entory. - Clear: Clear C all the tag informattion shown on the screen n.
Application option menu - Read/Write: Perform Read/Write. - Lock/Kill: Perform Lock/Kill. - Option: Application option - Version: Version information Read/Write Window - Mask: Selected value from main window is displayed here. It is used as masking pattern when performing Read/Write. Even if there are many tags nearby, only tags that are set as masking pattern can be read or written. - Kill Pwd, Access Pwd: Read/Write tag’s Kill password, access password. - EPC length: Read/Write tag’s EPC length.
Options Window - Session: Change Session that is used in Tag operation - Target: Change Target that is used in Tag operation - Q: Change Q that is used in Tag operation - LBT Ch State/Time: Change LBT option that is used in Europe, Japan frequencies (Not available) - Power: Change Tx Power level of the reader.
Chapter 5. Appendix Product Specifications Physical Characteristics Dimension(L*W*H) 76 X 148 X 24.8(30.5) mm Weight 320g (PDA only, without Battery) Operating Temp. -20℃ ~ 60℃ Storage Temp. -30℃ ~ 70℃ Humidity 95% Non-condensing Drop 1.5m Drop to concrete Performance Characteristics Processor Marvell PXA320 806MHz Operating System Windows CE 5.0 Memory 512MB RAM / 512MB ROM 3.
Writing Range 0m ~ 3m (According to Tag & Environment) Antenna Gain 2 dbi (Standard) Speed 62.
61 AT870N User Guide
