AT287-UHF User Guide
Disclaimer Reasonable measures have been taken to ensure that the information included in this manual is complete and accurate. However, ATID reserves the right to change any specification at anytime without prior notice. ATID is a registered trademark of ATID Co., Ltd. The ATID logo is a trademark of ATID, All other trademarks and trade names referred to herein are property of their respective owners. AT870 is a registered trademark of ATID Co., Ltd.,and of its wholly owned subsidiaries.
Table of contents Before You Begin ........................................................................................................................... 4 Chapter1. Caution when using ....................................................................................................... 5 1. How to use the battery correctly ................................................................................................. 5 2. Caution when using...........................................................
Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Who should read this manual? This manual is written for the person who is responsible for installing, configuring, and maintaining the AT287-UHF. This manual provides you with information about the features of the AT287-UHF, and how to install, configure, operate, and maintain it.
Chapter1. Caution when using Before you handle and operate your device, Please read through and familiar with the contents of this manual. 1. How to use the battery correctly When you dropped the main body or battery in water, please do not put it on the stove or heater for drying. Just keep it in natural temperature or contact with purchase place.
Chapter2. Products compositions This product is 900Mhz’s RFID Reader/Writer, which is recognized Tag’s data and it is transmitting to top units via Bluetooth. Its various function applied to Industry, Enterprise, Logistics and so on, can be used extensively in many fields. 1. Package components After opening the product packaging box, check the items listed as below: 1. AT287-UHF Body 2. Adaptor and AC Cable 4. Necklace Strap 3.
2.
3. Function of Each Part Part Description Scan LED Press the Scan button, it shows Access condition of RFID Tag. Power LED Power LED will be Red when the battery is charging, or will be green when it is charged completely. Power Key It is for device’s power on or off. Reset Key Reset AT287-UHF’s Device. Scan Button It is for reading data from RFID TAG, it is front and left/right side of product. BT/USB key Switch the data transfer mode. BT/USB LED Displays the current data transfer mode.
Chapter3. Basic Functions 1. Power and Battery Main Battery: 3.7V 800mA Lithium 1.1 Detaching and Attaching Battery Detaching Battery Open the battery Screw (UNLOCK Screw), and then lift the main battery out of the compartment along both sides of groove.
1.2 Charging Battery This product connects to your PC and Sync Cable for charging, or the product included in the charge via a dedicated AC-DC Adaptor is available. You have to charge the battery via dedicated adapter, which provided from the factory. “Power LED” is Red while charging or is Green when charged completely. . Connecting Adapter 1. 2. 3. Plug the adapter cable to 220V socket. Connect adapter DC cable to the “Power connecting jack” of the main body.
NOTE: Battery life is largely affected from the user using method and surrounding environments. 800mA battery is usually needs 4 ~ 12 hours to get charged completely. 2. Setting product operation mode When you use only this product, it will be working simply, unable to take of the data, And you can get only tag’s UID data 2.1 Switching the data transfer mode This device has three different type of data operation mode USB, Bluetooth.
⑥ ⑦ If you find the AT287-UHF, proceed the Paring The Pin code, Password is ‘0000” ⑧ Paring is completed on a PC Bluetooth, Please check the AT287-UHF’s Com port in the device manager or Bluetooth device management program ⑨ After running a dedicated PC Demo program, and set up the COM port, please press the Connect button for performing the task.
4. FCC Certification Requirements 1. Caution Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment. 2. FCC RF exposure requirements The antenna used with this module must be installed to provide a separation distance of at least 20cm from all persons, and must not transmit simultaneously with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. 3.